PowMr HHJ-60A/HHJ-80A/HHJ-100A

Contents

PowMr MPPT Solar Charge Controller User Manual

Models: HHJ-60A, HHJ-80A, HHJ-100A

For 12V/24V/36V/48V Systems

1. Introduction

Thank you for choosing the PowMr MPPT Solar Charge Controller. This manual provides essential information for the safe and efficient installation, operation, and maintenance of your solar charge controller. Please read this manual thoroughly before installation and use, and keep it for future reference.

The PowMr MPPT Solar Charge Controller is designed to maximize power harvesting from your solar panels and efficiently charge various battery types in 12V, 24V, 36V, and 48V off-grid or hybrid PV systems. It features advanced Maximum Power Point Tracking (MPPT) technology, high conversion efficiency, and comprehensive protection mechanisms to ensure safe and reliable operation.

PowMr MPPT Solar Charge Controller models
Figure 1: PowMr MPPT Solar Charge Controller (60A, 80A, 100A models shown). Supports LiFePo4 and 12V/24V/36V/48V battery voltages.

2. Safety Information

  • Read all instructions and warnings in the manual before installation.
  • Do not disassemble or attempt to repair the controller yourself. Refer to qualified service personnel.
  • Ensure all wiring is correct and connections are tight to avoid loose connections that may cause excessive heat.
  • Install the controller indoors in a well-ventilated area, away from direct sunlight, high temperatures, and moisture.
  • Always connect the battery first, then the solar panels, and finally the load. Disconnect in the reverse order: load, then solar panels, then battery.
  • Use appropriate circuit breakers or fuses for all connections (PV, battery, load) to prevent damage from overcurrent.
  • Wear eye protection when working with batteries.

3. Product Features

  • Advanced MPPT Technology: Up to 98% conversion efficiency and >99% MPPT tracking efficiency for maximum power harvesting.
  • Wide Voltage Compatibility: Supports 12V, 24V, 36V, and 48V battery systems with manual voltage selection.
  • Broad Battery Compatibility: Compatible with Lead-acid (Sealed, Gel, Float) and Lithium Iron Phosphate (4-cell, 8-cell, 16-cell) batteries. User-defined parameters are supported.
  • Three-Stage Charging: Features Fast Charging, Absorption, and Float Charging stages to optimize battery health and extend lifespan.
  • Comprehensive Protection: Includes PV reverse connection, short circuit, overcurrent, battery overcharge/over-discharge, load overload, and over-temperature protection.
  • User-Friendly Interface: LCD screen displays real-time voltage, current, power, temperature, and fault codes. Easy parameter settings via buttons.
  • Efficient Heat Dissipation: Forced air cooling with dual fans (on 80A/100A models) ensures stable operation within -35℃ to +45℃.
MPPT High Efficiency Tracking
Figure 2: MPPT High Efficiency Tracking, showing up to 99% tracking efficiency.
Multiple Protections for Safer Operation
Figure 3: Multiple Protections, including Reverse Polarity, Overtemperature, Overcurrent, Overcharge/Overdischarge, and Short Circuit.

4. Specifications

Parameter HHJ-60A HHJ-80A HHJ-100A
Rated Charge Current 60A 80A 100A
System Voltage 12V/24V/36V/48V Auto-recognition (Manual selection available)
Max. PV Input Voltage 155VDC
Max. PV Input Power (12V System) 720W 720W 720W
Max. PV Input Power (24V System) 1440W 1440W 1440W
Max. PV Input Power (36V System) 2100W 2100W 2100W
Max. PV Input Power (48V System) 2800W 2800W 2800W
PV Input DC Voltage Range (12V System) 20V-80V
PV Input DC Voltage Range (24V System) 37V-105V
PV Input DC Voltage Range (36V System) 50V-160V
PV Input DC Voltage Range (48V System) 72V-160V
Tracking Efficiency >99%
Conversion Efficiency Up to 98%
Battery Types Supported Lead-acid (Sealed, Gel, Float), Lithium Iron Phosphate (4-cell, 8-cell, 16-cell), User-defined
Load Output Current DC-5A
Operating Temperature -35℃ to +45℃
Dimensions (HHJ-60A) 214mm x 115mm x 50mm N/A (Dimensions may vary for 80A/100A)
Max PV Input Power and Input Specification DC
Figure 4: Maximum PV Input Power and DC Input Specifications for various system voltages.
HHJ-60A Dimensions
Figure 5: HHJ-60A dimensions: 214mm (L) x 115mm (W) x 50mm (H).

5. Installation

5.1 Unpacking and Inspection

Upon receiving the controller, carefully unpack it and inspect for any visible damage. Ensure all components are present according to the packing list.

5.2 Mounting Location

  • Install the controller indoors, in a dry, well-ventilated area.
  • Avoid direct sunlight, high temperatures, and moisture.
  • Mount vertically on a wall or sturdy surface to allow for proper airflow and heat dissipation.
  • Ensure sufficient clearance around the controller for cooling.

5.3 Wiring Instructions

IMPORTANT: Always connect the system in the following order: Battery, then Load, then PV array. Disconnect in the reverse order: Load, then PV array, then Battery.

  1. Prepare Wiring: Ensure all circuit breakers are open before making any connections. Use appropriate gauge wires for your system's current and distance.
  2. Connect Battery: Connect the positive (+) and negative (-) terminals of the battery to the corresponding BAT+ and BAT- terminals on the controller. Ensure correct polarity.
  3. Connect Load (Optional): If using a DC load directly from the controller, connect the positive (+) and negative (-) terminals of the load to the corresponding OUT+ and OUT- terminals on the controller. Ensure correct polarity.
  4. Connect Solar Panels: Connect the positive (+) and negative (-) terminals of your solar panel array to the corresponding PV+ and PV- terminals on the controller. Ensure correct polarity.
  5. Close Breakers: Once all connections are secure, close the battery breaker first, then the PV breaker. The controller should power on.
Clear Terminal Design for Easy Wiring
Figure 6: Bottom Terminal Layout for Easy Installation, showing PV Input, Battery Terminal, and Load Terminal.
Wiring Diagram
Figure 7: Schematic Wiring Diagram. Connect Battery, then Load, then PV array. Disconnect in reverse order.
2 Step Easy Connection
Figure 8: Two-step easy connection process: 1. Wire the battery (breaker open). 2. Wire solar panels (breaker open). 3. Connect battery (battery breaker close, controller power on). 4. Connect solar panels (both PV and battery breakers close, charging starts).

6. Operation

6.1 LCD Display and Buttons

The controller features an LCD display and four buttons for navigation and settings:

  • PRG/ESC: Program/Escape button. Used to enter/exit programming mode or return to the previous menu.
  • Up Arrow: Navigate up through menu options or increase values.
  • Down Arrow: Navigate down through menu options or decrease values.
  • ENTER: Confirm selection or enter a submenu.
Controller Parts and Functions
Figure 9: Controller overview with numbered parts: 1. LCD Display, 2. Function Buttons, 3. PV Input (+), 4. PV Input (-), 5. Battery Port (-), 6. Load Port (+), 7. Load Port (-), 8. Mounting Holes, 9. Battery Port (+), 10. Fan.

6.2 Working Modes

The controller operates in various modes depending on the system status:

  • Night Mode (3.0): No charging occurs.
  • MPPT Mode (4.0): Maximum Power Point Tracking is active, optimizing solar panel output for charging.
  • Absorption Mode (7.0): Battery is charged at a constant voltage to ensure full charge.
  • Floating Mode (8.0): Battery is maintained at a float voltage to prevent overcharging and self-discharge.
Working Modes and LCD Display
Figure 10: LCD screen displaying various parameters and working modes. Fan cooling is also depicted.

6.3 Battery Type and System Voltage Settings

The controller supports automatic system voltage recognition. However, you can manually select the system voltage and battery type through the LCD menu to match your specific setup. Refer to the on-screen menu for detailed navigation and parameter adjustment.

Supports Multiple Battery Types & System Voltages
Figure 11: Illustration of supported battery types (Lead-acid, Lithium) and system voltages (12V, 24V, 36V, 48V).

7. Maintenance

  • Regular Inspection: Periodically check all wiring connections for tightness and signs of corrosion.
  • Cleanliness: Keep the controller clean and free from dust. Use a dry cloth to wipe the exterior. Ensure ventilation openings are not blocked.
  • Fan Check: For models with fans (HHJ-80A/HHJ-100A), ensure the fans are operating correctly and are free from obstructions.
  • Battery Health: Monitor battery voltage and health regularly. Ensure batteries are properly maintained according to their manufacturer's guidelines.
  • Environmental Conditions: Ensure the installation environment remains within the specified operating temperature range (-35℃ to +45℃) and is free from excessive moisture.

8. Troubleshooting

Problem Possible Cause Solution
Controller not powering on Battery not connected or reverse polarity; battery voltage too low. Check battery connections and polarity. Ensure battery voltage is above minimum operating threshold.
No charging from PV PV panels not connected or reverse polarity; PV voltage too low/high; PV breaker open. Check PV connections and polarity. Ensure PV voltage is within specified range. Close PV breaker.
Battery not fully charged Insufficient PV power; incorrect battery type setting; battery degradation. Ensure adequate sunlight and PV array size. Verify battery type setting. Check battery health.
Load not working Load not connected or reverse polarity; load overload; battery low voltage disconnect. Check load connections and polarity. Reduce load. Charge battery.
Over-temperature warning Poor ventilation; high ambient temperature; fan malfunction. Improve ventilation around the controller. Check if fans are running (if applicable). Relocate if ambient temperature is too high.
Multi-function Protection
Figure 12: Multi-function Protection features, including Load short circuit, Battery over discharge, Battery reverse polarity, PV short circuit, PV over current alarm, Battery overcharge, Controller overheating, and Load overload protection.

9. User Tips

  • Optimal PV Sizing: To maximize efficiency, ensure your solar panel array's voltage and power are within the controller's specified limits for your chosen battery system voltage.
  • Lithium Battery Setup: When using lithium batteries, carefully set the charging parameters (e.g., absorption voltage, float voltage) according to the battery manufacturer's recommendations via the controller's menu.
  • Cable Sizing: Always use appropriately sized cables for all connections to minimize voltage drop and heat loss, especially for higher current models (80A/100A).
  • System Monitoring: Regularly check the LCD display for system status, charging current, and any fault codes to ensure optimal performance.

10. Warranty & Support

PowMr products are designed for reliability and performance. For warranty information, technical support, or service inquiries, please contact your retailer or the official PowMr support channels. Keep your purchase receipt as proof of purchase.

© 2023 PowMr. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.