1. Introduction
The Ultenic Pooleco 10 is a cordless robotic pool cleaner designed for efficient and hassle-free maintenance of both inground and above-ground pools. Featuring dual HyperPower motors, smart automation with one-click operation, and an auto-parking function, it provides a thorough cleaning experience for pools up to 850 sq ft.
2. Safety Information
- Always read and understand all instructions before using the appliance.
- Ensure the charging port is dry before connecting the charger.
- Do not operate the cleaner if the power cord or charger is damaged.
- Keep children and pets away from the pool area when the cleaner is in operation.
- Only use the charger supplied by the manufacturer.
- Do not use the cleaner to remove large debris that could clog the suction ports.
- Store the cleaner in a cool, dry place when not in use.
3. What's Included
Verify that all components are present in the package:
- 1 x Pooleco 10 Robotic Pool Cleaner
- 1 x Charger
- 1 x Floater Ball with Rope
- 2 x Brushes
- 2 x Wheels (Extra)
- 1 x User Manual (this document)
4. Setup
4.1 Initial Charging
- Before first use, fully charge the Pooleco 10.
- Connect the charger to the cleaner's charging port, ensuring the port is dry.
- Plug the charger into a power outlet. The intuitive display will show charging status.
- A full charge takes approximately 2.5 to 3 hours.
4.2 Pool Compatibility
The Pooleco 10 is suitable for:
- In-ground and above-ground pools without slopes.
- Pools up to 850 sq ft.
- Various pool shapes (round, square, irregular).
- Pool surfaces including tile, vinyl, plaster, fiberglass, and concrete.
It is not supported for pools with:
- Slopes greater than 10 degrees.
- Depths greater than 3 meters.
- Steps.
- Wall or waterline cleaning.
5. Operating Instructions
5.1 Starting the Cleaner
- Ensure the Pooleco 10 is fully charged.
- Place the cleaner into the pool.
- Press the "One Click" knob to initiate the cleaning cycle. The cleaner will automatically begin its cleaning path.
5.2 Cleaning Cycle and Runtime
- The Pooleco 10 operates for approximately 90 minutes on a full charge.
- It utilizes dual motors for 2x suction power, effectively removing leaves, dirt, sand, hair, and other debris.
- The TwinForce Pro System provides 360° dual scrubbing for thorough cleaning.
5.3 Auto-Parking and Retrieval
When the cleaning cycle is complete or the battery is low, the Pooleco 10 will automatically return to the edge of the pool for easy retrieval.
- The cleaner will dock itself near the pool edge.
- Use the floater ball with rope to gently pull the cleaner out of the water.
- Lift the cleaner using its handle.
6. Maintenance
6.1 Cleaning the Filter Tray
Regular cleaning of the filter tray is essential for optimal performance.
- After each use, remove the Pooleco 10 from the pool.
- Open the top cover of the cleaner.
- Remove the 2.5L filter basket.
- Rinse the 180um filter thoroughly with a hose to remove all collected debris.
- Reinsert the clean filter basket and close the top cover securely.
6.2 Brush and Wheel Maintenance
- Periodically check the brushes and wheels for wear and tear.
- Replace worn brushes or wheels with the provided extra parts as needed to maintain cleaning efficiency.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Cleaner does not start | Low battery; Power button not pressed; Obstruction | Charge the cleaner fully; Press the "One Click" knob firmly; Check for and remove any debris blocking the motors or wheels. |
| Poor cleaning performance | Clogged filter; Worn brushes/wheels; Large debris | Clean the filter basket; Replace worn brushes/wheels; Manually remove large debris before operating. |
| Cleaner does not auto-park | Battery too low; Sensor obstruction | Ensure cleaner is fully charged before use; Clean any debris from the cleaner's sensors. |
| Charging issue | Charger not connected properly; Damaged charger/port | Ensure secure connection; Check charger and port for damage; Contact support if damaged. |
8. Specifications
| Category | Detail |
|---|---|
| General |
Brand: Ultenic Type: Pool Cleaner Model: Pooleco 10 Color: Gray Power Source: Other (Battery) |
| Performance |
Motor: 2pcs (Dual HyperPower Motors) Battery capacity: 5200mAh Run time: 90min Charging time: ≤3H (approx. 2.5 hours) Max Pool Area: 850 sq ft Suction Power: 30 GPM |
| Dimensions & Weight |
Product Weight: 3.25kg Product Size (L x W x H): 32 x 32 x 16.5 cm Floater ball rope length: 2m |
| Electrical | Voltage: 10.8V |
9. User Tips
- For best results, ensure the pool water is clear of large debris (e.g., large branches) before operating the cleaner.
- Regularly clean the filter basket after each use to maintain strong suction and prevent clogging.
- Fully charge the cleaner before each cleaning cycle to ensure maximum runtime and efficient auto-parking.
- The Pooleco 10 is highly effective at picking up fine debris like sand, making it a great tool for simplifying overall pool maintenance.
10. Warranty and Support
For warranty information, technical support, or any questions regarding your Ultenic Pooleco 10 Robotic Pool Cleaner, please contact the seller or manufacturer directly. Refer to your purchase documentation for specific contact details.