1. Safety Information
To ensure your safety and prevent damage to the device or vehicle, please carefully read and follow all instructions in this manual before use.
When operating the device, always verify proper testing procedures and strictly adhere to the instructions provided. As automotive electrical systems may vary, you must assess potential risks and ensure a safe testing environment.
Always observe all safety warnings, use appropriate tools, and disconnect power sources when necessary. Improper operation may result in personal injury, equipment damage, or voided warranty.
Safety Messages
Safety messages use standardized signal words to indicate hazard levels and prevent injuries or equipment damage:
DANGER
- Will result in death or serious injury if ignored.
- Indicates an immediately life-threatening hazard.
- Always ventilate the service area when engine is running or use building exhaust removal system if available.
- Carbon monoxide is odorless and deadly - can cause loss of consciousness or death.
WARNING
- Could result in death or serious injury if ignored.
- Indicates a potentially dangerous situation.
- Always conduct testing in a safe, controlled environment.
- Wear ANSI-approved safety goggles during all operations.
- Keep all objects away from moving or hot engine components.
- Ensure proper ventilation to avoid toxic exhaust fumes.
- Secure the vehicle in PARK (automatic) or NEUTRAL (manual) with parking brake engaged.
- Place wheel chocks and never leave the vehicle unattended during tests.
- Exercise extreme caution around ignition systems - hazardous voltages are present.
- Maintain an ABC-rated fire extinguisher within immediate reach.
- Never connect/disconnect test equipment with ignition on or engine running.
- Keep all test equipment clean, dry and free from contaminants.
- Never operate test equipment while driving - focus solely on testing.
- Strictly follow the vehicle service manual's diagnostic procedures.
- Verify full battery charge and secure DLC connections before testing.
- Never place test equipment near the distributor due to EMI risks.
2. Setup
2.1 Device Button Layout Explained
Familiarize yourself with the buttons and display of your VD31 device:

Image: VD31 device with labeled buttons and 2.8-inch LCD screen.
- 2.8 Inch LCD Screen: Displays information.
- Up Button: Menu navigation up, previous page in multi-screen info, edits DTC characters.
- Shutdown Button: Powers off the device.
- Right Button: Next page in multi-screen info.
- Key Battery Button: Direct access to key battery voltage measurement.
- Down Button: Menu navigation down, next page in multi-screen info, edits DTC characters.
- I/M Button: Checks emissions readiness and drive cycle status.
- Left Button: Previous page in multi-screen info.
- ESC Button: Returns to previous screen (press once to exit other tests).
- LED For Different DTC Types: Provides visual indicators.
- OK Button: Confirms selection.
2.2 Power Connection Methods
The VD31 can be powered in three ways:
Vehicle Power Connection (Recommended)
- Locate the vehicle's Data Link Connector (DLC), typically under the dashboard.
- With the vehicle ignition ON, connect the code reader to the DLC.
- The device will auto-power on.
Important:
- Never use Type-C power during vehicle communication.
- Ensure clean connector contact.
Computer Connection (For Updates/Data Transfer)
- Connect the Type-C cable to the device and a computer.
- The device will auto-power on.
Built-in 9V Battery (For Key Battery Check Only)
- Insert a fresh 9V battery into the compartment.
- The device will auto-power on when the battery is installed.
2.3 Location of the Data Link Connector (DLC)
The Data Link Connector (DLC), also known as the Diagnostic Link Connector, is a standardized 16-pin port used to connect diagnostic scan tools to the vehicle's onboard computer.

Image: Diagram showing common locations for the Data Link Connector (DLC) in a vehicle: left corner of dash, near center of dash, and behind ashtray.
Typical DLC Locations:
- Most vehicles: Within 12 inches of the dashboard center, typically under or near the driver's side.
- Some Asian/European models: Behind the ashtray (may require removal for access).
- If not visible: Check for a location label or consult the vehicle's service manual.
3. Operating Instructions
3.1 Application Overview
Upon startup, you'll see these preloaded applications:
- OBDII/EOBD: Shows the OBDII screen for all nine OBD system tests.
- Battery: Shows a screen that tests and displays the voltage of the vehicle battery.
- Key Battery: Shows a screen to test and display the vehicle key fob battery level.
- DTC Lookup: Shows a screen for diagnostic trouble code lookup.
- Review: Shows a screen for access to tested data files.
- Print: Shows a screen for access to the printing function.
- Setting: Shows a screen for access to modify your settings like Language, Unit of Measure, etc.
3.2 OBDII/EOBD Functions
When you select the OBDII/EOBD application from the home screen, your vehicle's diagnostic information will display. Press OK to access the diagnostic menu with these available tests:
Diagnostic Test Menu:
- Read DTC
- Clear DTC
- Live Data
- Freeze Frame
- MIL Status
- Vehicle Info
- O2 Sensor
- Mode 6 (On-Board Monitoring)
- Mode 8 (EVAP System Test)
3.2.1 Read DTC (Diagnostic Trouble Codes)
This function allows you to check stored fault codes in the vehicle's control modules.
Available Code Types:
- Stored DTCs
- Pending DTCs
- Permanent DTCs
- Record DTC
To read codes from a vehicle:
- Select "Read DTC" from the OBDII/EOBD menu using the arrow keys, then press OK.
- Choose the code type (Stored, Pending, or Permanent DTCs) and confirm with OK.
- The tool will display all detected codes along with their descriptions.
Stored DTCs
Stored DTCs are active fault codes that are stored in the vehicle's ECU when the onboard diagnostic system confirms a problem. These codes will typically illuminate the check engine light (MIL) immediately upon detection. Current DTCs can be cleared using the code reader's erase function, though some may clear automatically after several problem-free drive cycles if the issue doesn't recur.
Pending DTCs
Pending DTCs are temporary fault codes stored when a potential issue is first detected by your vehicle's monitoring systems. Unlike regular trouble codes, these won't turn on the check engine light immediately. The system keeps them as a warning - if the problem happens again on your next drive, they'll turn into confirmed trouble codes and activate the warning light. You can clear these pending codes with your code reader, or they'll disappear automatically if the issue doesn't recur after several driving cycles. These codes are useful for spotting intermittent problems early or checking if a repair fixed an issue.
Permanent DTCs
Permanent DTCs are fault codes that were severe enough to originally trigger the check engine light (MIL), and remain stored in the vehicle's computer even after the light turns off. These codes preserve a record of the fault whether the MIL was cleared manually or stopped illuminating because the problem didn't reoccur. They automatically erase only after: (1) the underlying issue is fully repaired, and (2) the system successfully completes 3 consecutive drive cycles without detecting the fault.
3.2.2 Clear DTC
This function allows you to clear stored diagnostic trouble codes (DTCs) from the vehicle's ECU with the ignition ON (engine OFF).

Image: Dashboard showing 'Before' (check engine light on) and 'After' (check engine light off) clearing codes.
To erase codes from a vehicle:
- Select "Clear DTC" from the OBDII menu.
- Follow the on-screen prompts to confirm and complete the erasure.
- Immediately rescan the system to check for remaining codes.
After Erasure:
If codes persist: This may indicate permanent DTCs. Please repair or replace the affected components before attempting to clear the codes again.
3.2.3 Live Data
This function allows real-time monitoring of vehicle sensor data and system parameters (PIDs) from the ECU.

Image: Screen displaying live data in a graphical format, showing various parameters like RPM, load, and temperatures.
- View All Items: Displays real-time monitoring of all available vehicle parameters from the ECU, including engine RPM, coolant temperature, fuel trim values (both short-term and long-term), oxygen sensor voltages, throttle position, and other critical system measurements.
- Select Items: Enables focused monitoring of specific vehicle parameters. To view selected PIDs:
- Navigate through the parameter list using the UP/DOWN button.
- Press OK to select/deselect each desired parameter.
- Press ESC to display all selected parameters in real-time.
- View Graphic Items: Allows you to view PID data as a graphing.
- Record All: Used to record PIDs to help diagnose intermittent drivability problems that can't be determined by any other method.
- Record Select: Allows you to record the PID data you selected.
CAUTION:
- Always park the vehicle before using the code reader.
- When recording live data during driving, ensure two occupants are present - one to drive and one to operate the device.
NOTE:
Vehicle communication speeds and supported PIDs vary by make/model/year. Some parameters may not be available on all vehicles.
3.2.4 Freeze Frame
The Freeze Frame function provides a snapshot of critical vehicle parameters (engine RPM, load, fuel system status, etc.) recorded at the moment a fault code was triggered. This data helps diagnose intermittent issues by showing exact operating conditions when the problem occurred.
To access freeze frame Data:
- Select "Freeze Frame" from the OBDII menu.
- Scroll through recorded parameters using the UP/DOWN button.
- View detailed condition readings for each parameter.
Note: If no data is available, the display will show "No freeze frame data stored".
3.2.5 MIL Status
Performing the MIL status function will show you detailed information, such as the Check Engine Light status, the Run Time with Check Engine Light on, and the Distance with Check Engine Light on.
3.2.6 Vehicle Information
The Vehicle Information function retrieves the vehicle's VIN number, calibration IDs (identifying control module software versions), and calibration verification numbers (CVNs), which are values calculated according to OBDII regulations to verify whether emission-related calibrations have been modified.
Note that multiple CVNs may be reported for a single control module and the calculation process may take several minutes to complete. Available options will vary depending on the connected vehicle.
3.2.7 O2 Sensor Test
The O2 Sensor Test opens a menu of tests available for checking the integrity of the oxygen sensors. Making a selection displays all of the pertinent O2S parameters for the specific test.
3.2.8 On-Board Monitoring (Mode 6)
The On-Board Monitoring (Mode 6) function is useful after servicing or after clearing a vehicle ECU's memory. It receives test results for emission-related powertrain components and systems that are not continuously monitored for Non-CAN vehicles. For CAN vehicles, it receives test data for emission-related powertrain components and systems that are and are not continuously monitored. It is the vehicle manufacturer who is responsible for assigning test and component IDs.
NOTE:
Test results do not necessarily indicate a faulty component or system.
To request On-board Monitor Test (Mode 6) results:
- Use the UP/DOWN key to highlight "On-board Monitor Test (Mode 6)" from the OBDII/EOBD menu and press the OK key.
- A screen with details of the selected sensor displays. Use the UP/DOWN arrow keys to scroll through data to select lines.
3.2.9 EVAP System Test (Mode 8)
The EVAP System Test (Mode 8) allows the code reader to control the operation of vehicle components and tests of systems.
EVAP (Evaporative Emission Control System) is an automotive system designed to prevent fuel vapor from escaping into the atmosphere, thereby reducing air pollution.
Its main functions include:
- Preventing Fuel Vapor Leakage: The EVAP system captures and stores fuel vapor to avoid its escape into the environment while the vehicle is in operation or parked.
- Storing Vapor: The system uses a fuel vapor canister to store vapors, minimizing their impact on the environment.
- Recycling Vapor: When the engine is running, the system directs the stored vapor back to the combustion chamber via an electromagnetic valve for re-burning, enhancing fuel efficiency.
- Monitoring for Leaks: The EVAP system is equipped with sensors that monitor pressure changes in real-time to detect any leaks within the system, ensuring its integrity.
- Improving Fuel Efficiency: By effectively capturing and reusing fuel vapor, the EVAP system contributes to improved fuel economy and reduced fuel consumption.
NOTE:
- Some manufacturers do not allow tools to control vehicle systems.
- The manufacturer sets the criteria to automatically stop the test. Refer to the appropriate vehicle service manual before using this function.
3.2.10 I/M Readiness
I/M Readiness, or Inspection and Maintenance Readiness, refers to the status of a vehicle's on-board diagnostic (OBD) system's readiness to perform emissions testing. It indicates whether the various emissions-related systems on the vehicle are operating properly and have completed their self-diagnostic checks. This is crucial for passing state emissions inspections, as some monitors must be "ready" for the vehicle to be compliant.

Image: VD31 screen showing I/M Readiness status with MIL, DTC, Pd DTC, and various system checks (MIS, FUE, CCM, CAT, HCAT, EVAP, AIR, O2S, HRT).
Monitor Status:
- OK: Test completed successfully.
- INC (Incomplete): Test not yet finished (needs more driving).
- N/A (Not Applicable): This monitor is not required/supported for your specific vehicle.
There are two types of I/M Readiness tests:
- Since DTCs Cleared: Shows the status of monitors since the last time diagnostic trouble codes (DTCs) were cleared.
- This Drive Cycle: Shows the status of monitors since the beginning of the current driving cycle.
NOTE:
- To check I/M Readiness status, ensure the ignition is ON (engine OFF).
- Monitor availability varies by vehicle specifications.
To retrieve I/M Readiness Status data by one-click I/M Readiness hotkey:
- Press the I/M Readiness hot key on the keypad.
- The screen will display the I/M Readiness status.
- Colored LED and built-in beeper provide both visual and audible reminders for emission check and DTCs.
When the LED is:
- Yellow: The tool finds a possible problem. It indicates the following two conditions:
- Pending DTCs exist. Please check the I/M Readiness test result screen and use the Read Codes function to view detailed codes information.
- Some of the vehicle's emission monitors have not worked properly. If the I/M Readiness screen shows no DTC (including pending DTC), but the Yellow LED is still illuminated, it indicates a "Monitor Has Not Run" status.
- Red: Indicates some problems exist with one or more of the vehicle's systems, and the vehicle is not ready for an Emissions Test. As well, DTCs are found. The MIL lamp on the vehicle's instrument panel will light steady. The problem that is causing the illumination of the Red LED should be fixed before an Emissions Test or driving the vehicle further.
NOTE:
The built-in beeper, which makes different tones corresponding to different LED indicators, is invaluable when the test is performed while driving or in bright areas where LED illumination may not be visible.
3.2.11 Full OBD2 Functions Overview

Image: Icons representing various full OBD2 functions including Read Trouble Code, Clear Trouble Code, Read Freeze Frame, Live Data, I/M Readiness, On-Board Monitor Test, O2S Monitoring, Component Test, Vehicle Information, Modules Present.
The VDIAGTOOL VD31 code reader supports all OBD2 modes, including:
- Reading Codes: Show the detailed description of the Diagnostic Trouble Code (DTCs).
- Erasing Codes & Reset: Turns off Check Engine Light (MIL), clears codes and resets monitors.
- Data Stream: Reads and displays live ECU/PCM data stream, plotting functions graphically and stores freeze frame data.
- I/M Readiness Status: Shows whether the various emissions-related systems on the vehicle are operating properly and are ready for inspection and maintenance testing.
- Read Live Data Stream: Show the information of continuous data stream from a vehicle in live graphic (waveform) display.
- View Freeze Frame Data: Check the certain vehicle conditions which are recorded by the on-board computer at the time the emission-related fault occurs.
- O2 Sensor Test: Allows retrieval and viewing of O2 sensor monitor test results for the most recently performed tests from the vehicle’s on-board computer.
- On-Board Monitor Test: Retrieves and displays test results for emission-related powertrain components and systems.
- Read Vehicle Information: Display the information such as VIN (Vehicle Identification Number), CID (Calibration ID) and CVN (Calibration verification number), etc.
- Component Test: Certain vehicle components can be actuated by commands sent from the scanner to test their operability.
3.3 Battery Test (Vehicle Battery Voltage)
This function provides real-time battery voltage monitoring.

Image: VD31 displaying "Battery Volt 12.1V" with a battery icon, indicating normal battery voltage and good status.
The device displays the current vehicle battery voltage, helping you determine the health and condition of your car battery.
3.4 Key Fob Battery Check
The device displays the installed 9V battery level in the top-right corner. This feature allows you to test your car key fob battery.

Image: VD31 testing a car key fob battery, showing 433.92MHz - 50% battery level. Instructions for testing are provided.
3.4.1 Test the New Key
For first-time use, select "Test The New Key" to add the test key.
New Key Identification Methods:
- Brand Selection: For more accurate key battery level testing, select your vehicle brand directly. This method skips manual scanning by leveraging pre-configured frequency data tailored to your car model, ensuring higher detection accuracy for key battery status.
How to Use:
- Navigate to "Brand Selection" in the menu.
- Choose your vehicle manufacturer from the list.
- Follow on-screen prompts (e.g., press the key button) to test the battery.
- Automatic Scan:
- Position the key in the device's top-left sensing area (align with the signal icon).
- Press the key function button every 3 seconds until a success message appears.
- Frequency Selection:
- Adjust frequency value:
- Up/Down buttons: Change digit value.
- Left/Right buttons: Move cursor position.
- Press OK to confirm when "Scan successful" appears.
- Adjust frequency value:
3.4.2 Test The Store Key
Successfully tested keys are automatically saved in the stored key menu for future testing, eliminating the need for re-identification.
To test or delete stored keys:
Press OK when viewing the list of keys.
Note:
It is recommended to press the OK button to freeze the reading when the key battery level is read, because if the key is accidentally moved, the test result may become 0%. Of course, you can put the key close to the sensing area again, and then press the function key (lock or unlock), and the reading will appear again. After pressing the OK button, if you want to re-measure, press ESC to exit and re-measure.
3.5 DTC Lookup
This function provides instant access to the built-in diagnostic trouble code database, containing both SAE standard and manufacturer-specific code definitions.
To Search for DTC Definitions:
- Select "DTC Lookup" from the main menu.
- Enter the code using:
- LEFT/RIGHT to navigate character positions.
- UP/DOWN to change digit values.
- OK to confirm.
- View the code definition.
Note:
- For manufacturer-specific codes (P1xxx/C1xxx/B1xxx/U1xxx), select the vehicle make.
- If no definition is found, consult the vehicle service manual.
3.6 Review (Recorded Data)
This function provides access to all recorded diagnostic data through the following menu options:
- Review DTC
- Review Datastream
- Review Freeze Frame
- Delete DTC Data
- Delete Datastream
- Delete Freeze Frame
To review or delete recorded data:
- Select "Review" from the main menu.
- Navigate through the six options using the UP/DOWN button.
- Press OK to view or delete selected data.
4. Maintenance
4.1 Updating the Code Reader
- Download and install the VD31 Update Client from https://www.vdiagtool.com/support/downloads.
- Launch the VD31 Update Client.
- With the device powered off, hold the Down button while connecting via USB-C until "UPDATE MODE" appears.
- Click "Upgrade" in the client software and wait for completion.
4.2 Printing Data
This function transfers saved diagnostic data to your computer as a .txt file for printing.

Image: VD31 connected to a computer and printer, illustrating the data printing process.
- Open the VD30 Pro software and connect the device to your computer.
- Click "Print" in the software.
- On the device, select the required data to print and confirm.
- The data will transfer as a .txt file.
- Click "Open File" in the software to locate and print the report.
4.3 Self Tests
This feature verifies the proper operation of the device hardware components.
Available Tests:
- Keys Test
- TFT Test
- LED Test
4.3.1 Keys Test
Selecting the Keys Test option opens a screen that allows you to check the functionality of the keypad.
To test the keypad:
- Select "Key Test" from the Self-Test menu.
- Press any button - the display will show the button name.
- Double-press ESC to exit.
4.3.2 TFT Test
Selecting the TFT Test option opens a screen that allows you to check the functionality of the screen.
To test the screen:
- Select "TFT Test".
- Visually inspect for:
- Dead pixels.
- Color uniformity.
- Press ESC to complete.
4.3.3 LED Test
Selecting the LED Test option opens a screen that allows you to check the functionality of the LED.
To test the LED:
- Select "LED Test".
- All status LEDs will illuminate sequentially.
- Press ESC to terminate.
5. Troubleshooting
- Persistent DTCs: If Diagnostic Trouble Codes (DTCs) persist after clearing, this may indicate permanent DTCs or an underlying issue. Please repair or replace the affected components before attempting to clear the codes again.
- DTC Definition Not Found: If the device cannot find a definition for a specific DTC, consult the vehicle's service manual for more information.
- Negative Error Code Identification: If the device successfully erases errors but the identification result for a specific code is unclear or negative, consider cross-referencing the DTC with a vehicle service manual or reliable online resources for more accurate diagnosis.
- Device Not Powering On: Ensure the device is properly connected to the vehicle's DLC with the ignition on, or to a computer via Type-C cable, or has a fresh 9V battery installed (for key battery check only). Check for clean connector contacts.
- Key Fob Battery Reading is 0%: If the key fob is accidentally moved during testing, the reading may drop to 0%. Reposition the key close to the sensing area and press the function key (lock or unlock) again. Press OK to freeze the reading once stable.
6. Specifications
| Attribute | Value |
|---|---|
| Model Name | VDIAGTOOL VD31 |
| Item Type | Engine Analyzer |
| Display | 2.8" TFT color |
| Operating Temperature | 0°C to 60°C (32°F to 140°F) |
| Storage Temperature | -20°C to 70°C (-4°F to 158°F) |
| Connection | Wired via main cable |
| Power Source | OBDII port connection, Type-C cable, or built-in 9V battery |
| Compatibility | OBDII & EOBD (12V) vehicles |
| Dimensions (L x W x H) | 15cm x 9cm x 5cm (6.5×3.54×1.18 inches) |
| Item Weight | 1kg (8.47 oz) |
| Material | Plastic |
| Software Update | Yes |
| Hardware Version | 2026 |
| Software Version | 2026 |
| External Testing Certification | CC |
| Origin | Mainland China |
7. Warranty & Support
7.1 Limited Three Years Warranty
The VDIAGTOOL VD31 is warranted against defects in materials and workmanship for three years (36 months) from the date of delivery to the buyer. This warranty does not cover any part that has been abused, altered, used for a purpose other than for which it was intended, or used in a manner inconsistent with instructions regarding use. The exclusive remedy for any tool found to be defective is repair or replacement, and the manufacturer shall not be liable for any consequential or incidental damages.
7.2 Contact Us
If you have any questions or need assistance, feel free to contact our support team:
- Support Email: support@vdiagtool.com
- Official Website: www.vdiagtool.com
- US Hotline: +1-213-355-7171
- Online Form: https://www.vdiagtool.com/support/tech-support
7.3 User Manual (PDF)
A copy of the user manual in PDF format is available for download. You can access it via the device's menu under "Manual" or directly from the official website:
- PDF Manual Link: VDIAGTOOL VD31 User Manual (PDF)
8. User Tips
- Vehicle Compatibility: Functions may vary from car to car. It is recommended to contact the seller or consult the official website to check compatibility for your specific vehicle model before extensive use.
- Key Fob Battery Testing: For a precise reading of your key fob battery, try to enter the key's exact frequency if known (often found on the key itself or via a quick web search). Remove the 9V battery from the VD31 when not testing key fobs to preserve its charge.
- Stable Key Fob Readings: When testing a key fob battery, press the OK button to 'freeze' the reading once it's stable. If the key is accidentally moved, the reading might drop to 0%. Simply reposition the key and re-test.
- DTC Definition Verification: While the device provides a comprehensive DTC database, if you encounter a negative or unclear error code identification result, always cross-reference with your vehicle's service manual or other trusted online resources for the most accurate diagnosis.