1. Important Safety Precautions
IMPORTANT!
Your satisfaction is very important to us. If you encounter any issues such as shipping damage, missing parts, error code, defects, etc., please contact customer support for a satisfactory solution. Please do not return the product until you have contacted us.
Contact E-Mail: service_sports@163.com
Please provide your Order ID and a description of the Product problem (attach pictures or videos if necessary).
2. Setup and Assembly
2.1. Package Contents
Before assembly, ensure all parts are present and undamaged.
| No. | Item | Quantity |
|---|---|---|
| 1 | Remote Control | 1 |
| 2 | User Manual | 1 |
| 3 | Boost | 1 |
| 4 | Phone holder | 1 |
| 5 | Upper case | 1 |
| 6 | Armrest watch holder | 1 |
| 7 | Running deck | 1 |
| 8 | Washer M8 | 2 |
| 9 | Spring washer M8 | 2 |
| 10 | Steel ball latch M8*39 | 2 |
| 11 | Hexagon socket head cap screw M8*20 | 2 |
| 12 | Cross-recessed flat head self-tapping screw ST4*12 | 3 |
| 13 | Latex hole plug | 2 |
| 14 | 5#Hex key | 1 |
| 15 | 6#Hex key | 1 |
| 16 | Knob M8*20 | 2 |
| 17 | Knob M8*35 | 1 |
| 18 | 13-14-15 multi-functional screwdriver | 1 |
2.2. Assembly Steps
- STEP1: Check if all parts are complete.
- STEP2: Install the armrest watch holder.
- Align the tube holes of armrest holder (6) with running deck (7) sleeves.
- Use screws (11) with washers (8) and spring washers (9).
- Tighten clockwise with hex key (15) to secure.
- Fit knob (16) into the front hole as shown.
Note: This knob is for positioning to prevent shaking; it's normal if it can't be fully tightened.

Image: Diagram showing the assembly of the armrest watch holder, indicating parts like Knob M8*20 (16), Hexagon socket head cap screw M8*20 (11), Spring washer M8 (9), Washer M8 (8), and 5#Hex key (14).
- STEP3: Install the side armrests, upper case, and phone holder.
- Align the side armrest holes with those on the armrest tube.
- Insert steel ball latch (10).
- Align upper case (5) and phone holder (4) with the lower case holes on the armrest tube.
- Use 2 screws (12) and multi-function screwdriver (18) to tighten clockwise at marked positions for securing.
- Insert phone holder into the case's corresponding position.

Image: Diagram illustrating the assembly of the side armrests, upper case, and phone holder, pointing out the phone holder (4), steel ball latch M8*39 (10), cross-recessed flat head self-tapping screw ST4*12 (12), and multi-function screwdriver (18).
- STEP4: Install the hole plugs and adjust the foot pads.
- Take silicone hole plugs (13) and install them into the marked holes on the armrest tubes.
- Adjust the folding foot pads on running deck (7) to the unfolded position.

Image: Diagram showing the installation of latex hole plugs (13) into the armrest tubes and the adjustment of the folding foot pads.
- STEP5: Installation completed.

Image: A view of the treadmill after full assembly.
- STEP6: Storage state.
- Pull out the side armrest latch.
- Loosen armrest tube knob (16) counterclockwise.
- Fold the armrest watch holder down to the diagram position.
- Align its middle hole with the running deck sleeve.
- Secure with knob (17) (one side only).

Image: The treadmill folded for storage, showing knob M8*35 (17) securing the folded armrest.
2.3. Incline Adjustment
This machine is equipped with two levels of incline adjustment. Adjust the angle according to your actual needs.
- Ensure that the support feet are properly adjusted to avoid unnecessary injuries.
- The height-increasing foot pads should only be used after the support feet have been fully extended.
- If the rear cover touches the ground, adjust the height of the rear foot pads.
To adjust, rotate the support leg to adjust the height from the ground to prevent the rear guard from scraping against the floor. For higher incline, put the support leg into the boost.

Image: Diagram illustrating the incline adjustment, showing how to position the support leg for high or low incline using a boost mechanism.
3. Operating Instructions
3.1. Remote Control Setup
- Insert 2 AAA batteries (not included) into the remote controller.
3.2. Treadmill Operation
- Turn on the power switch of the treadmill.
- In standby mode, press the 'M' key to enter three countdown modes: Time, Distance, and Calorie. During mode selection, the indicator light for the current mode will always be on.
- Select one of the modes you want. Use the '+' and '-' keys to increase and decrease the value of the countdown function.
- After setting the countdown value, press 'ON/OFF' to run.
- To quit the countdown function or stop the treadmill, press 'ON/OFF' again.

Image: The treadmill's remote control, showing buttons for Start, Stop, Speed+, Speed-, and Pause. The LED screen displays Speed, Time, Distance, and Calories.
Note: The images are for reference only. The actual remote control may differ due to variations in production batches.
3.3. Exercise Modes
The ROBORE X5F offers 4-in-1 exercise modes to suit various fitness goals:
- Working Mode: 0.6-1.5 MPH
- Walking Mode: 0.6-2.5 MPH
- Jogging Mode: 2.5-4.0 MPH
- Running Mode: 4.0-6.3 MPH

Image: Visual representation of the four exercise modes: Working, Walking, Jogging, and Running, with their respective speed ranges and incline levels.
4. Maintenance
4.1. Lubrication
Correct lubrication of the treadmill with silicon oil or Teflon is important. (ONLY FOR NORMAL BELT, IF NEEDED)
This lubrication must be performed regularly depending on its use, even before the first use.
- Lift the belt.
- Add the oil under the belt.
- After starting the machine, change to the highest speed. The oil will spread from the middle between the running belt and board.

Image: A hand applying lubricant under the treadmill belt, next to a lubrication schedule table.
Lubrication Schedule
| Usage Frequency | Maintenance Frequency |
|---|---|
| <3 Hours/Week | 2 Months |
| 4-7 Hours/Week | 1 Month |
| >8 Hours/Week | 2 Weeks |
The treadmill was pre-oiled for instant use, and the oil provided is 30ml. Under normal circumstances, it can be used for about one year. If your usage time is around 4-7 hours per week, and the maintenance time is one month, then the approximate amount of oil used each time is 2.5ml.
4.2. Running Belt Corrections
If the running belt is offsetting to the left or right with a rattling noise, adjust it to the correct position.
- Check if the Running Belt is offsetting to the left or right with a rattling noise.
- If the problem occurs, adjust the running belt to the correct position.

Image: Diagrams showing how to adjust the running belt if it shifts to the left or right, indicating to tighten/loosen screws clockwise (CW) or counter-clockwise (CCW).
WARNING: Don't put your hand between the roller and running belt, otherwise you will squeeze your fingers.
If the running belt slips, use a 5mm wrench to turn both sides bolts 1/4 clockwise. Repeat this procedure until the belt is properly tightened.
Caution:
- Heavy pedaling may cause shutdown (overload protection, not machine failure).
- Current and voltage overload may cause shutdown.
- Each person's running habits (how hard the left or right foot tread) may cause the running belt to shift slightly.
5. Troubleshooting
| Error Code | Error | Judgment | Solution |
|---|---|---|---|
| E1 | Connection Error |
|
|
| E2 | Motor Damaged |
|
|
| E5 | Over-current Protection |
|
|
| E6 | Motor Over-voltage Protection |
|
|
6. Specifications
6.1. General Features
| Attribute | Detail |
|---|---|
| Brand | ROBORE |
| Type | Treadmill |
| Model | X5F |
| Color | Black |
6.2. Technical Specifications
| Attribute | Detail |
|---|---|
| Input Voltage | AC 220-240V |
| Motor | 2.5HP |
| Weight Capacity | 330lbs / 150kg |
| Max. Speed | 10km/h (6.3 MPH) |
| Speed Range | 1-10km/h (0.6-6.3 MPH) |
| Incline Levels | 2%, 10%, 14% (3-level adjustable) |
| Running Belt | Non-slip diamond pattern, multi-layer shock-absorbing system |
| Running Belt Dimensions | 35.8" x 15.2" |
| Noise Level | <45db |
| Display | LED Screen (Speed, Time, Distance, Calories) |
| Control | Remote Control |
| Versatility | Under-desk usable for office settings, adjustable handles |
6.3. Weight & Size
| Attribute | Detail |
|---|---|
| Product Weight | 18kg |
| Package Weight | 21kg |
| Product Size (L x W x H) | 107.7 x 58 x 114.2 cm (42.4" x 22.8" x 45") |
| Package Size (L x W x H) | 119 x 62 x 11.2 cm |

Image: The treadmill in its upright folded position, with dimensions 42.4" (length), 22.8" (width), and 45" (height) indicated.
7. Warranty and Support
7.1. 5 Year Warranty
The ROBORE X5F Treadmill provides a 5-year warranty.
Warranty Description:
- 5 Year Frame
- 1 Year Parts
7.2. Customer Support
Contact CursorCare for 7/24 response and 100% satisfaction guarantee.
- 7*24 Online Support: California-based customer service team to solve after-sales problems without obstacles.
- Return Policy: 30-Day Hassle-Free Return and Exchange.
- Personalized Solutions: California-based service team providing personalized solutions to ensure 100% customer satisfaction.
- Exclusive Maintenance Service: We honor our commitment to quality and durability by offering free maintenance tools for orders within 6 months, including lubricants and remote control.
Customer Support E-Mail: service_sports@163.com
8. User Tips
- Start Slowly: If you are new to treadmills, begin with walking at a comfortable pace to get accustomed to the machine.
- Proper Footwear: Always wear appropriate athletic shoes to ensure comfort and reduce the risk of injury.
- Stay Hydrated: Keep a water bottle nearby and drink water regularly, especially during longer workouts.
- Listen to Your Body: Do not overexert yourself. If you feel pain or discomfort, stop your workout.
- Regular Cleaning: Wipe down the treadmill after each use to remove sweat and dust, which helps maintain its condition.
- Check Belt Alignment: Periodically check the running belt for proper alignment to prevent wear and tear and ensure smooth operation.