SHIMANO NEXUS C7000 Series

Contents

SHIMANO NEXUS C7000 Internal Geared Hub Groupset User Manual

Models Covered: SG-C7000-5D, SL-C7000-5, CJ-C7000-5, CS-C7000 27T

Document Number: DM-CASG002-05

1. Introduction and Important Safety Information

This manual provides instructions for the installation, operation, maintenance, and troubleshooting of the SHIMANO NEXUS C7000 Internal Geared Hub Groupset. Please read this manual thoroughly before use and follow all instructions for correct and safe operation.

Important Notice

  • This dealer's manual is intended primarily for use by professional bicycle mechanics. Users who are not professionally trained for bicycle assembly should not attempt to install the components themselves. If any part of the information is unclear, contact your place of purchase or a local bicycle dealer for assistance.
  • Always read all instruction manuals included with the product.
  • Do not disassemble or modify the product other than as stated in this manual.
  • All manuals and technical documents are accessible online at https://si.shimano.com.
  • For consumers without internet access, contact a SHIMANO distributor or office for a hardcopy of the User's Manual.
  • Observe appropriate rules and regulations of your country, state, or region.

DANGER

Failure to follow instructions will result in death or serious injury.

WARNING

Failure to follow instructions could result in death or serious injury.

CAUTION

Failure to follow instructions could cause personal injury or physical damage to equipment and surroundings.

General Safety Precautions

  • Wear approved eye protection when performing maintenance tasks.
  • Learn proper braking technique for your bicycle model. Improper use can lead to loss of control.
  • Keep fingers away from rotating disc brake rotors; they are sharp.
  • Do not touch calipers or disc brake rotors immediately after braking, as they will be hot.
  • Avoid oil or grease on disc brake rotors and brake pads.
  • Do not use brake pads if thickness is 0.5 mm or less.
  • Do not use disc brake rotor if cracked, deformed, or thickness is 1.5 mm or less.
  • Do not continuously apply brakes when riding down long slopes to prevent overheating and reduced braking performance.
  • Do not press the pedal strongly while gear shifting.
  • The internal geared hub is not completely waterproof. Avoid water ingress and high-pressure washing.

2. Components Overview

The SHIMANO NEXUS C7000 Groupset includes the following original SHIMANO parts:

SHIMANO NEXUS C7000 Groupset components
Overview of the SHIMANO NEXUS C7000 Groupset components.

Product Overview Video

A short video demonstrating the SHIMANO NEXUS C7000 groupset components.

Included Parts:

  • SL-C7000-5 REVOSHIFT Shift Lever: Ergonomic and light operation, dedicated for E-BIKE use.
  • SL-C7000-5 Shift Lever
    SL-C7000-5 Shift Lever.
  • SG-C7000-5D Internal Geared Hub (Disc Brake) 5s: E-BIKE dedicated IHG with higher shifting performance for mid-ship motors, offering greater strength and durability.
  • SG-C7000-5D Internal Geared Hub
    SG-C7000-5D Internal Geared Hub.
  • CJ-C7000-5 Cassette Joint: Part for use with the SG-C7000-5 internal gear rear hub.
  • CJ-C7000-5 Cassette Joint
    CJ-C7000-5 Cassette Joint.
  • CS-C7000 27T Single Sprocket: Part for use with the SG-C7000-5 internal gear rear hub.
  • CS-C7000 27T Single Sprocket
    CS-C7000 27T Single Sprocket.
  • Additional small parts such as nuts, washers, and rings are also included for installation.

3. Specifications

General Product Specifications

Attribute Value
Brand Name SHIMANO
Series SHIMANO NEXUS C7000 Series
Category Bearing Hub
Number of Holes 36 Holes
Hub Hole Number 32/36 Holes
Spoke Hole 29 - 36
Origin Jp(origin)

Models Covered

Part/Series Brake Type INTER-5E Model
Internal geared hub Coaster brake + Disc brake -
Disc brake SG-C7000-5D
Coaster brake SG-C7000-5C
INTER M brake SG-C7000-5R
V-BRAKE SG-C7000-5V
Shift lever REVOSHIFT lever SL-C7000-5

Gear Ratio Information

It is recommended that the front chainring have a tire size of 28 inches or shorter and be set so that the gear ratio is about 1.4 as shown in the table below. For more detailed information on usable gear ratios, refer to the full dealer's manual.

Chainring CS-C7000 (Sprocket Teeth)
34 24
38 27
42 30

Package Details

  • Weight: 2.95 kg
  • Dimensions: 20 cm (Length) x 20 cm (Width) x 15 cm (Height)

4. Setup and Installation

This section outlines the steps for installing the SHIMANO NEXUS C7000 groupset components. Ensure you have the necessary tools before beginning.

Required Tools

Tool Description
3 mm hexagon wrench For various fasteners.
Screwdriver (#1) For various fasteners.
TL-S700-B Special tool for specific tasks.
10 mm spanner For nuts and bolts.
TL-LR10 Lock ring tool.
Adjustable wrench For various fasteners.

4.1. Installation of the Sprocket to the Hub

  1. Install the right-hand dust cap C to the driver in the orientation shown in the illustration.
  2. Install the sprocket and secure it in place with the snap ring.
Sprocket installation diagram
Diagram showing the installation of the sprocket to the hub.

4.2. Installation of the Cassette Joint to the Hub

  1. Install the driver cap to the driver as shown. Note the orientation of the driver cap.
  2. Turn the cassette joint pulley to align the red marks on the pulley and the bracket.
  3. Install the cassette joint with the red marks on the cassette joint aligned with the red marks on the right side of the hub body.
  4. Secure the cassette joint to the hub with the cassette joint mounting ring. Align the yellow mark on the mounting ring with the yellow mark on the pulley.
  5. Turn the cassette joint mounting ring 45° clockwise. Hold down the bracket securely.
Cassette joint installation diagram
Diagram showing the installation of the cassette joint to the hub.

4.3. Installing the INTER M Brake to the Hub Body

  1. Engage the hub body splines with the INTER M brake splines, then temporarily tighten with the brake unit fixing nut.

4.4. Installation of the Hub to the Frame

  1. Mount the chain on the sprocket, and then set the hub axle into the rear dropout.
  2. Place non-turn washers onto the right and left sides of the hub axle. Ensure the protrusions fit into the rear dropout grooves and align the joint parallel to the chainstay.
  3. For INTER M brake specifications, attach the brake arm to the chainstay with the brake arm clip. Temporarily fix the clip bolt and clip nut by lightly tightening them.
  4. Take up slack in the chain and secure the wheel to the frame with the cap nut.

4.5. Installation of the Disc Brake Rotor

  1. For center lock type, install the disc brake rotor and secure it with the disc brake rotor fixing lock ring.
  2. Tighten the lock ring to 40 N-m using the TL-LR10 tool.

4.6. Installation of the Shifting Cable

  1. Installation of the Lever: Attach the grip spacer to the lever and pass it through the handlebar. Attach the half grip. Tighten the fixing bolt with a 3 mm hexagon wrench to 2-2.5 N-m.
  2. Installation of the Shifting Cable (CJ-C7000-5):
    • Pass the inner cable through the OT-SP41 outer casing to the end with the plastic cap.
    • Set SL-C7000-5 to gear 5.
    • If rubber bellows and a rubber cover are attached, install them to the outer casing holder body.
    • Wipe off any grease on the inner cable.
    • Pass the inner cable through the outer casing holder body.
    • If rubber bellows and a rubber cover are attached, hold the end of the rubber bellows and insert the inner cable. Slide and set the rubber bellows.
    • Set the outer casing to the outer casing holder body. Push the outer casing so that it securely touches the outer casing holder body.
    • Attach the inner cable mounting bolt unit to the inner cable. Tighten to 3.5-5.5 N-m.
    • Turn the lever of the pulley clockwise.
    • Bring the cable around to the cassette joint pulley, hold it so that the inner cable fixing nut is facing outside, and then slide the flats part of the inner cable fixing washer into the gap in the pulley.
    • Turn the cable 60° counterclockwise and attach it to the hook.
    • Set the inner cable in the pulley, insert the inner cable into the slit in the cassette joint bracket, then securely set the outer casing holder body into the outer casing holder section of the cassette joint.

5. Operating Instructions

Shifting Gears

The SL-C7000-5 REVOSHIFT shift lever allows for ergonomic and light gear changes. To shift, rotate the grip. For optimal performance and to prevent damage, reduce the force applied to the pedals when shifting. Shift one gear at a time. Attempting to multi-shift with strong pedal force can cause issues like the chain coming off or the bicycle falling over.

Braking

The SG-C7000-5D hub supports disc brakes. Apply brakes smoothly and gradually. Avoid sudden, hard braking unless necessary. Be aware that brake components can become very hot during use, so avoid touching them immediately after riding.

6. Maintenance

Regular maintenance ensures the longevity and optimal performance of your SHIMANO NEXUS C7000 groupset.

6.1. Adjusting the Cassette Joint

  1. Set the SL-C7000-5 lever to gear 5.
  2. Set the SL-C7000-5 lever to gear 3.
  3. Check that the yellow setting lines on the cassette joint bracket and pulley are aligned with each other. If they are not aligned, turn the cable adjustment barrel of the REVOSHIFT lever until they align. Move the REVOSHIFT lever once more from 3 to 5 and then back to 3, and then re-check alignment.
  4. After adjusting, cut off any excess inner cable and install the inner end cap.

6.2. Disconnecting the Shifting Cable (for Rear Wheel Removal)

  1. Set SL-C7000-5 to gear 5.
  2. Press the lever of the pulley clockwise to loosen the inner cable.
  3. Remove the outer casing holder from the outer casing holder section of the cassette joint.
  4. Remove the inner cable from the slit in the bracket.
  5. Remove the inner cable fixing bolt unit from the cassette joint pulley.
  6. Detach the wheel.

6.3. Replacing the Inner Cable

  1. Set SL-C7000-5 to gear 5.
  2. Loosen the cover fixing screw (3mm hexagon wrench, 0.1-0.25 N-m).
  3. Remove the cover.
  4. Remove the inner cable mounting bolt unit from the cassette joint pulley.
  5. Pass the new inner cable from the hole in the winder unit through the hole in the cable adjustment barrel. Insert the inner cable into the groove of the cable guide. Pull the inner cable so that the inner cable drum fits into the recess in the winder unit.
  6. Replace the cover and tighten the cover fixing screws.

6.4. Oil Maintenance of the Internal Assembly

To maintain proper performance, it is recommended to lubricate the internal unit once a year (or every 2,000 km for frequent use). More frequent maintenance is required under harsh conditions. Use SHIMANO internal geared hub grease or a lubrication kit. If not used, malfunctions may occur.

  1. Fill a container with SHIMANO WB maintenance oil (Y00298010) to a height of 95 mm.
  2. Immerse the internal unit in the oil from the left side until the oil reaches up to ring gear unit 1.
  3. Keep the internal unit immersed for approximately 90 seconds.
  4. Remove the internal unit from the oil.
  5. Let excess oil drain off for approximately 60 seconds.
  6. After oil maintenance, apply grease (Y04130100) to the ball retainers, snap ring, brake shoe, and pinion gears.

7. Troubleshooting

This section addresses common phenomena and potential issues with the internal geared hub.

Common Phenomena and Solutions

Phenomenon Gear Positions Affected Notes/Solution
Noise occurs when the pedals rotate. All gear positions except 1st Due to internal gear-shifting structure, not a failure.
Noise occurs when the bicycle is pushed backward. All gear positions except 1st Due to internal gear-shifting structure, not a failure.
Hub mechanism noise/vibrations during shifting. All gear positions Built-in mechanism supports gear shifting; noise/vibrations are normal.
Gear-shifting feels different depending on gear position. All gear positions Normal operation due to internal structure.
Noise occurs when pedal rotation is stopped during riding. All gear positions Due to internal gear-shifting structure, not a failure.
Wheel becomes stiff or difficult to turn (Coaster brake). N/A Replace brake shoes or lubricate with grease.
Chain keeps coming off the gears. N/A Replace the gears and chain.

8. User Tips

  • Dropout Compatibility: If your bike has vertical dropouts, the hub axle washers are designed to accommodate this. You can adjust or swap the washers to achieve the correct angle and secure fit. Refer to online videos or a professional mechanic if unsure.
  • E-Bike Integration: This groupset is designed for E-BIKE use and works effectively with mid-ship motors like Bafang, providing smooth and reliable performance.

9. Warranty and Support

For maximum performance, SHIMANO highly recommends using genuine SHIMANO lubricants and maintenance products. Products are not guaranteed against natural wear and deterioration from normal use and aging.

Contact Information

  • SHIMANO NORTH AMERICA BICYCLE, INC.
    One Holland, Irvine, California 92618, U.S.A.
    Phone: +1-949-951-5003
  • SHIMANO EUROPE B.V.
    High Tech Campus 92, 5656 AG Eindhoven, The Netherlands
    Phone: +31-402-612222
    EU General Contact: contactshimano@shimano-eu.com
  • SHIMANO INC.
    3-77 Oimatsu-cho, Sakai-ku, Sakai City, Osaka 590-8577, Japan

For the complete dealer's manual and additional technical documents, please refer to the official PDF: SHIMANO NEXUS C7000 Dealer's Manual (PDF).

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.