1. Introduction
The VDIAGTOOL VD31 is a versatile OBDII/EOBD multifunctional code reader designed for both automotive professionals and DIY enthusiasts. It offers a 3-in-1 functionality covering car key battery testing, vehicle battery health checks, and comprehensive engine code scanning. With advanced features like real-time data graphics and an extensive DTC library, the VD31 simplifies vehicle diagnostics and maintenance.
This device supports switching between 8 languages: English, Chinese, French, Spanish, German, Russian, Italian, and Polish.

2. Safety Information
To ensure your safety and prevent damage to the device or vehicle, please carefully read and follow all instructions in this manual before use.
General Safety Guidelines
- When operating the device, always verify proper testing procedures and strictly adhere to the instructions provided.
- As automotive electrical systems may vary, you must assess potential risks and ensure a safe testing environment.
- Always observe all safety warnings, use appropriate tools, and disconnect power sources when necessary. Improper operation may result in personal injury, equipment damage, or voided warranty.
Safety Messages
Safety messages use standardized signal words to indicate hazard levels and prevent injuries or equipment damage:
DANGER
Will result in death or serious injury if ignored. Indicates an immediately life-threatening hazard.
WARNING
Could result in death or serious injury if ignored. Indicates a potentially dangerous situation.
Specific Safety Instructions
- Always ventilate the service area when the engine is running or use a building exhaust removal system if available. Carbon monoxide is odorless and deadly and can cause loss of consciousness or death.
- Always conduct testing in a safe, controlled environment.
- Wear ANSI-approved safety goggles during all operations.
- Keep all objects away from moving or hot engine components.
- Ensure proper ventilation to avoid toxic exhaust fumes.
- Secure the vehicle in PARK (automatic) or NEUTRAL (manual) with the parking brake engaged.
- Place wheel chocks and never leave the vehicle unattended during tests.
- Exercise extreme caution around ignition systems - hazardous voltages are present.
- Maintain an ABC-rated fire extinguisher within immediate reach.
- Never connect/disconnect test equipment with ignition on or engine running.
- Keep all test equipment clean, dry, and free from contaminants.
- Never operate test equipment while driving - focus solely on testing.
- Strictly follow the vehicle service manual's diagnostic procedures.
- Verify full battery charge and secure DLC connections before testing.
- Never place test equipment near the distributor due to EMI risks.
3. General Information on OBDII/EOBD
3.1 On-Board Diagnostics (OBD) II
OBD II continuously or periodically monitors emission control systems and critical engine components through specialized tests. If an issue is detected, the system activates a Malfunction Indicator Light (MIL) on the dashboard, typically labeled "Check Engine" or "Service Engine Soon."
Additionally, OBD II records essential diagnostic data to assist technicians in identifying and resolving problems efficiently. Key information includes:
- MIL Status: Whether the warning light is activated ("on") or deactivated ("off").
- Diagnostic Trouble Codes (DTCs): Specific error codes stored in the system.
- Readiness Monitor Status: The completion status of emission-related self-tests.
3.2 Diagnostic Trouble Codes (DTCs)
DTCs are alphanumeric codes stored by the vehicle's OBD II system when a malfunction is detected. These codes help pinpoint the source of a problem, serving as a guide for troubleshooting.
An OBD II DTC follows a 5-character format:
- First character (letter): Indicates the affected system:
- P = Powertrain (Engine/Transmission)
- B = Body (e.g., Airbags, Climate Control)
- C = Chassis (e.g., ABS, Stability Control)
- U = Network/Communication (e.g., CAN Bus)
- Remaining four digits: Specify the exact issue.

3.3 Location of the Data Link Connector (DLC)
The Data Link Connector (DLC) is a standardized 16-pin port used to connect diagnostic scan tools to the vehicle's onboard computer.
Typical DLC Locations:
- Most vehicles: Within 12 inches of the dashboard center, typically under or near the driver's side.
- Some Asian/European models: Behind the ashtray (may require removal for access).
- If not visible: Check for a location label or consult the vehicle's service manual.
4. Setup and Getting Started
4.1 Included Accessories
- Type-C Cable: For computer connection and firmware updates.
- User Manual: Complete operation instructions (this document).
4.2 Technical Specifications
| Feature | Specification |
|---|---|
| Display | 2.8" TFT color |
| Operating Temperature | 0°C to 60°C (32°F to 140°F) |
| Storage Temperature | -20°C to 70°C (-4°F to 158°F) |
| Connection | Wired via main cable |
| Power Source | OBDII port connection, Type-C cable, or built-in 9V battery |
| Compatibility | OBDII & EOBD (12V) vehicles |
| Dimensions | 6.5 × 3.54 × 1.18 inches |
| Weight | 8.47 oz |
4.3 Power Connection Methods
Power on your code reader by connecting to vehicle power or a computer before using any applications.
Vehicle Power Connection (Recommended)
- Locate the vehicle's DLC (typically under the dashboard).
- With the ignition ON, connect the code reader to the DLC.
- The device will auto-power on.
Important:
- Never use Type-C power during vehicle communication.
- Ensure clean connector contact.
Computer Connection (For Updates/Data Transfer)
- Connect the Type-C cable to the device and computer.
- The device will auto-power on.
Built-in 9V Battery (For Key Battery Check Only)
- Insert a fresh 9V battery into the compartment.
- The device will auto-power on when the battery is installed.
4.4 Application Overview
Upon startup, you'll see these preloaded applications:
- OBDII/EOBD: Shows the OBDII screen for all nine OBD system tests.
- Battery: Shows a screen that tests and displays the voltage of the vehicle battery.
- Key Battery: Shows a screen to test and display the vehicle key fob battery level.
- DTC Lookup: Shows a screen for diagnostic trouble code lookup.
- Review: Shows a screen for access to tested data files.
- Print: Shows a screen for access to the printing function.
- Setting: Shows a screen for access to modify your settings like Language, Unit of Measure, etc.
5. Operating Instructions
5.1 Control Buttons

- ESC button: Returns to the previous screen (press once to exit other tests).
- Up button: Menu navigation up; previous page in multi-screen info; edits DTC characters.
- Power button: Short press to power on; long press (3s) to power off.
- Left button: Previous page in multi-screen info.
- OK button: Confirms selection.
- Right button: Next page in multi-screen info.
- I/M button: Checks emissions readiness and drive cycle status.
- Down button: Menu navigation down; next page in multi-screen info; edits DTC characters.
- Key Battery button: Direct access to key battery voltage measurement.
5.2 OBDII/EOBD Functions
When you select the OBDII/EOBD application from the home screen, your vehicle's diagnostic information will display. Press OK to access the diagnostic menu with these available tests:
- Read DTC
- Clear DTC
- Live Data
- Freeze Frame
- MIL Status
- Vehicle Info
- O2 Sensor
- Mode 6 (On-Board Monitoring)
- Mode 8 (EVAP System Test)
5.2.1 Read DTC
This function allows you to check stored fault codes in the vehicle's control modules. Available Code Types: Stored DTCs, Pending DTCs, Permanent DTCs, Record DTC.
To read codes from a vehicle:
- Select "Read DTC" from the OBDII/EOBD menu using the arrow keys, then press OK.
- Choose the code type (Stored, Pending, or Permanent DTCs) and confirm with OK.
- The tool will display all detected codes along with their descriptions.
Stored DTCs
Active fault codes stored in the vehicle's ECU when the onboard diagnostic system confirms a problem. These typically illuminate the Check Engine Light (MIL). Can be cleared using the code reader's erase function or may clear automatically after several problem-free drive cycles.
Pending DTCs
Temporary fault codes stored when a potential issue is first detected. These won't immediately turn on the Check Engine Light. If the problem recurs, they become confirmed DTCs. Can be cleared with the code reader or disappear if the issue doesn't recur.
Permanent DTCs
Severe fault codes that originally triggered the MIL and remain stored even after the light turns off. They preserve a record of the fault. Automatically erase only after the underlying issue is fully repaired and the system successfully completes 3 consecutive drive cycles without detecting the fault.
5.2.2 Clear DTC
This function allows you to clear stored diagnostic trouble codes (DTCs) from the vehicle's ECU with the ignition ON (engine OFF).
To erase codes from a vehicle:
- Select "Clear DTC" from the OBDII menu.
- Follow the on-screen prompts to confirm and complete the erasure.
- Immediately rescan the system to check for remaining codes.
After Erasure:
If codes persist, this may indicate permanent DTCs. Repair or replace affected components before attempting to clear codes again.
5.2.3 Live Data
This function allows real-time monitoring of vehicle sensor data and system parameters (PIDs) from the ECU.
- View All Items
- Select Items
- View Graphic Items
- Record All
- Record Select
CAUTION:
- Always park the vehicle before using the code reader.
- When recording live data during driving, ensure two occupants are present - one to drive and one to operate the device.
NOTE:
Vehicle communication speeds and supported PIDs vary by make/model/year. Some parameters may not be available on all vehicles.

5.2.4 Freeze Frame
The Freeze Frame function provides a snapshot of critical vehicle parameters (engine RPM, load, fuel system status, etc.) recorded at the moment a fault code was triggered. This data helps diagnose intermittent issues by showing exact operating conditions when the problem occurred.
To access Freeze Frame Data:
- Select "Freeze Frame" from the OBDII menu.
- Scroll through recorded parameters using the UP/DOWN button.
- View detailed condition readings for each parameter.
Note:
If no data is available, the display will show "No freeze frame data stored."
5.2.5 MIL Status
Performing the MIL status function will show you detailed information, such as the Check Engine Light status, the Run Time with Check Engine Light on, the Distance with Check Engine Light on, etc.

5.2.6 Vehicle Information
The Vehicle Information function retrieves the vehicle's VIN number, calibration IDs (identifying control module software versions), and calibration verification numbers (CVNs).
Note:
Multiple CVNs may be reported for a single control module, and the calculation process may take several minutes. Available options vary depending on the connected vehicle.
5.2.7 O2 Sensor
The O2 Sensor Test opens a menu of tests available for checking the integrity of the oxygen sensors. Making a selection displays all pertinent O2S parameters for the specific test.
5.2.8 On-Board Monitoring (Mode 6)
This function is useful after servicing or clearing a vehicle ECU's memory. It receives test results for emission-related powertrain components and systems that are not continuously monitored for Non-CAN vehicles. For CAN vehicles, it receives test data for both continuously and non-continuously monitored components.
NOTE:
Test results do not necessarily indicate a faulty component or system.
To request On-board Monitor Test (Mode 6) results:
- Use the UP/DOWN key to highlight "On-board Monitor Test (Mode 6)" from the OBDII/EOBD menu and press the OK key.
- A screen will show the monitor list.
- Use the UP/DOWN key to highlight a test group and press the OK key to confirm; a screen with details of the selected sensor displays. Use the UP/DOWN arrow keys to scroll through data to select lines.
5.2.9 EVAP System Test (Mode 8)
The EVAP System Test (Mode 8) allows the code reader to control the operation of vehicle components and test systems.
EVAP (Evaporative Emission Control System) is an automotive system designed to prevent fuel vapor from escaping into the atmosphere, thereby reducing air pollution. Its main functions include:
- Preventing Fuel Vapor Leakage: Captures and stores fuel vapor.
- Storing Vapor: Uses a fuel vapor canister.
- Recycling Vapor: Directs stored vapor back to the combustion chamber via an electromagnetic valve.
- Monitoring for Leaks: Sensors monitor pressure changes to detect leaks.
- Improving Fuel Efficiency: By effectively capturing and reusing fuel vapor.
NOTE:
- Some manufacturers do not allow tools to control vehicle systems.
- The manufacturer sets the criteria to automatically stop the test. Refer to the appropriate vehicle service manual.
5.2.10 I/M Readiness
I/M Readiness refers to the status of a vehicle's on-board diagnostic (OBD) system's readiness to perform emissions testing. This is crucial for passing state emissions inspections.
Monitor Status:
- OK: Test completed successfully.
- INC (Incomplete): Test not yet finished (needs more driving).
- N/A (Not Applicable): This monitor is not required/supported for your specific vehicle.
There are two types of I/M Readiness tests:
- Since DTCs Cleared: Shows the status of monitors since the last time diagnostic trouble codes (DTCs) were cleared.
- This Drive Cycle: Shows the status of monitors since the beginning of the current driving cycle.
NOTE:
- To check I/M Readiness status, ensure the ignition is ON (engine OFF).
- Monitor availability varies by vehicle specifications.
To retrieve I/M Readiness Status data by one-click I/M Readiness hotkey:
- Press the I/M Readiness hot key on the keypad.
- The screen will display the I/M Readiness status.
Colored LEDs and a built-in beeper provide both visual and audible reminders for emission checks and DTCs.
5.3 Battery Voltage Monitoring
This function provides real-time battery voltage monitoring.

The display will show the current battery voltage and status (e.g., "Normal battery voltage, good battery status.").
5.4 Key Fob Battery Check
The device displays the installed 9V battery level in the top-right corner.

5.4.1 Test the New Key
For first-time use, select "Test The New Key" to add the test key.
New Key Identification Methods:
- Brand Selection: For more accurate key battery level testing, select your vehicle brand directly. This method skips manual scanning by leveraging pre-configured frequency data tailored to your car model, ensuring higher detection accuracy.
How to Use (Brand Selection):
- Navigate to "Brand Selection" in the menu.
- Choose your vehicle manufacturer from the list.
- Follow on-screen prompts (e.g., press the key button) to test the battery.
- Frequency Selection:
How to Use (Frequency Selection):
- Adjust frequency value:
- Up/Down buttons: Change digit value.
- Left/Right buttons: Move cursor position.
- Press OK to confirm when "Scan successful" appears.
5.4.2 Test The Stored Key
Successfully tested keys are automatically saved in the stored key menu for future testing, eliminating the need for re-identification.
You can test or delete stored keys by pressing OK.
Note:
It is recommended to press the OK button to freeze the reading when the key battery level is read, because if the key is accidentally moved, the test result may become 0%. You can put the key close to the sensing area again, and then press the function key (lock or unlock), and the reading will appear again. After pressing the OK button, if you want to re-measure, press ESC to exit and re-measure.
5.5 DTC Lookup
This function provides instant access to the built-in diagnostic trouble code database, containing both SAE standard and manufacturer-specific code definitions.
To Search for DTC Definitions:
- Select "DTC Lookup" from the main menu.
- Enter the code using:
- LEFT/RIGHT to navigate character positions.
- UP/DOWN to change digit values.
- OK to confirm.
- View the code definition.
Note:
- For manufacturer-specific codes (P1xxx/C1xxx/B1xxx/U1xxx), select the vehicle make.
- If no definition is found, consult the vehicle service manual.

6. Settings
This menu allows you to customize the code reader's configuration to suit your preferences.
Available Options:
- Language: Select display language.
- Unit of Measure: Choose metric/imperial units.
- Self Tests: Run device self-test.
- Help: Access device information.
- Beep: Turn beep on or off.
6.1 Language
Selecting Language opens a screen that allows you to choose the system language.
To configure system language:
- Select "Language" from the Settings menu.
- Choose your desired language from the available list.
- Confirm selection with OK.
6.2 Unit of Measure
This setting allows you to switch between measurement systems:
Available Options:
- Metric (km/h, °C)
- US Customary (mph, °F)
Configuration Steps:
- Select "Unit of Measure" from the Settings menu.
- Choose the preferred system.
- Confirm with OK.
6.3 Self Tests
This feature verifies the proper operation of the device hardware components.
Available Tests:
- Keys Test
- TFT Test
- LED Test
6.3.1 Keys Test
Selecting the Keys Test option opens a screen that allows you to check the functionality of the keypad.
To test the keypad:
- Select "Key Test" from the Self-Test menu.
- Press any button - the display will show the button name.
- Double-press ESC to exit.
6.3.2 TFT Test
Selecting the TFT Test option opens a screen that allows you to check the functionality of the screen.
To test the screen:
- Select "TFT Test".
- Visually inspect for:
- Dead pixels.
- Color uniformity.
- Press ESC to complete.
6.3.3 LED Test
Selecting the LED Test option opens a screen that allows you to check the functionality of the LED.
To test the LED:
- Select "LED Test".
- All status LEDs will illuminate sequentially.
- Press ESC to terminate.
6.4 Help
Access this section for essential product information and diagnostic references.
Available Resources:
- Device Information
- About OBD
- About Data Stream
6.4.1 Tool Information
This option will show information about your code reader, such as hardware and software version.
6.4.2 About OBD
This option will show you what OBD is, OBDII modes, and vehicle coverage.
6.4.3 About Datastream
This option will show you brief introductions about each sensor and module.
6.5 Beep
Opens a settings dialog to enable/disable the keypress sound from the built-in speaker.
7. Maintenance
7.1 Review
This function provides access to all recorded diagnostic data through the following menu options:
- Review DTC
- Review Datastream
- Review Freeze Frame
- Delete DTC Data
- Delete Datastream
- Delete Freeze Frame
To review or delete recorded data:
- Select "Review" from the main menu.
- Navigate through the six options using the UP/DOWN button.
- Press OK to view or delete selected data.
7.2 Updating the Code Reader
The VD31 offers lifetime free software updates via connection to a Windows 7/8/10 PC using the included USB cable.
- Download and install the VD31 Update Client from https://www.vdiagtool.com/support/downloads.
- Launch the VD31 Update Client.
- With the device powered off, hold the Down button while connecting via USB-C until "UPDATE MODE" appears.
- Click "Upgrade" in the client software and wait for completion.
7.3 Printing
This function transfers saved diagnostic data to your computer as a .txt file for printing.
- Open the VD30 Pro software (or equivalent update client) and connect the device to your computer.
- Click "Print" in the software.
- On the device, select the test results to print and confirm.
- The data will transfer as a .txt file.
- Click "Open File" in the software to locate and print the report.

7.4 Manual Access
A copy of the user manual in PDF format will show up when you click this option in the update client. You can also download the PDF manual directly from this link.
7.5 Software Language Setting
This option allows you to set the language of the update client.
8. Troubleshooting
Many common issues can be resolved by understanding the device's functions and following proper procedures.
- Persistent DTCs after clearing: If Diagnostic Trouble Codes (DTCs) reappear immediately after being cleared, this indicates an underlying mechanical or electrical issue that requires repair. The VD31 can help identify these codes, but it cannot fix the physical problem.
- Device not powering on: Ensure the device is properly connected to the vehicle's OBDII port with the ignition on, or to a computer via the Type-C cable. If using the 9V battery for key fob testing, ensure it is fresh and correctly inserted.
- Inaccurate Key Fob Battery Readings: For accurate readings, ensure the key fob's exact frequency is entered (often found on the key or via web search). Keep the key fob close to the scanner's sensing area. If the reading drops to 0%, reposition the key and re-test.
- I/M Readiness Monitors Incomplete: If monitors show as 'INC' (Incomplete), it means the vehicle has not completed the necessary drive cycles for those tests. Continue driving the vehicle under various conditions until the monitors show 'OK'.
- No Freeze Frame Data: If the display shows "No freeze frame data stored," it means no fault code was active at the time of the last check, or the fault was not severe enough to trigger a freeze frame.
9. User Tips
- Regular Key Fob Checks: Utilize the dedicated key fob battery test function regularly, especially before long trips, to avoid unexpected lockouts or starting issues. Remember to remove the 9V battery from the VD31 when not in use to preserve its charge.
- Understand DTCs: Don't just clear codes; use the DTC Lookup function to understand what each code means. This knowledge empowers you to make informed decisions about repairs or maintenance.
- Monitor I/M Readiness: Before a state emissions inspection, use the one-click I/M Readiness hotkey to ensure all monitors are 'OK'. This can save you time and hassle by identifying incomplete tests beforehand.
- Leverage Live Data: For intermittent problems, use the Live Data function to monitor parameters in real-time. The 4-in-1 graphic display can help you spot anomalies that might not trigger a fault code immediately.
- Keep Software Updated: Regularly check for and install software updates via the VDIAGTOOL website. Updates often include expanded vehicle compatibility, bug fixes, and new features.
10. Warranty and Support
10.1 Limited Two Years Warranty
The VDIAGTOOL VD31 is warranted against defects in materials and workmanship for two years (24 months) from the date of delivery to the buyer. This warranty does not cover any part that has been abused, altered, used for a purpose other than for which it was intended, or used in a manner inconsistent with instructions regarding use. The exclusive remedy for any tool found to be defective is repair or replacement, and VDIAGTOOL shall not be liable for any consequential or incidental damages.
10.2 Contact Us
For warranty and support, please contact:
- Email: support@vdiagtool.com
- Official Website: www.vdiagtool.com
- US Hotline: +1-213-355-7171
- Online Form: https://www.vdiagtool.com/support/tech-support
For wholesale business or to become a distributor:
- Email: sales@vdiagtool.com
To invent with us or test products:
- Email: inventers@vdiagtool.com
To create social media content or join our community:
- Email: marketing@vdiagtool.com