1. Introduction
This manual provides detailed instructions for the safe and effective use of your AMBITFUL 360° Double Ballhead Magic Arm and Super Clamp Kit. Designed for photographers and videographers, this versatile accessory allows for flexible mounting of cameras, monitors, LED lights, microphones, and other equipment. Please read this manual thoroughly before use and retain it for future reference.
2. Safety & Warnings
Important Safety Information:
Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.
- Keep the device and its cord out of reach of children under 3 years old.
- Keep away from children unless supervised by an adult.
- Do not use this product for purposes other than its intended use.
- Inspect the product before each use; do not use if damaged.
- Follow installation and operation guidelines to avoid injury.
- Do not expose to water or moisture.
- Handle with care to avoid cuts or injuries.
3. Setup and Assembly
The AMBITFUL Magic Arm and Super Clamp Kit offers versatile mounting options. Follow these steps for typical assembly:
-
Attaching the Super Clamp (GM-C1):
The GM-C1 Super Clamp is designed for flat and curved surfaces with a maximum opening of 70mm. Turn the red knob counter-clockwise to open the clamp jaws. Position the clamp on a stable surface (e.g., table edge, pole) and turn the knob clockwise to secure it firmly. The clamp features anti-slip silicone pads for a secure grip.
Figure 2: Super Clamp (GM-C1) in use, demonstrating its clamping capability. The GM-C1 also features 1/4" threaded holes, ARRI positioning points, and cold shoe mounts for attaching various accessories.
Figure 3: Anti-Deflection Design of the Super Clamp, showing 1/4" screw holes, ARRI positioning points, and cold shoe mounts. -
Attaching the Magic Arm (GM-C2 / GM-C3):
The GM-C2 (145mm) and GM-C3 (220mm) Magic Arms feature a double ball-head design for 360° tilt and rotation. They typically connect via a 1/4" screw or cold shoe mount.
- To a 1/4" screw mount: Align the 1/4" screw on the magic arm with the corresponding threaded hole on your equipment (e.g., camera cage, clamp). Rotate the knurled wheel to tighten.
- To a cold shoe mount: Slide the cold shoe base of the magic arm into a cold shoe receiver on your equipment (e.g., camera, cage). Tighten the knurled wheel to secure.
Figure 4: Detail of the cold shoe mount on the Magic Arm for easy installation. -
Connecting Magic Arm to Super Clamp:
The Magic Arm can be attached to the Super Clamp using its 1/4" screw or cold shoe mount, depending on the available interface on the clamp. Ensure a secure connection by tightening the respective knobs.
4. Operation
The Magic Arm features a dual ball-head design, allowing for 360° tilt and rotation at each joint. This provides extensive flexibility for positioning your equipment.
-
Adjusting Position: Loosen the central red knob on the Magic Arm to adjust the angle and orientation of the ball joints. The joints offer 270° tilt and 360° rotation for precise positioning.
Figure 5: The 360° Double Ball Joint allows for versatile positioning with 270° tilt and 360° rotation. -
Locking Position: Once the desired position is achieved, tighten the central red knob clockwise to lock all moving components securely. This independent knob adjustment ensures swift tension control.
Figure 6: The knob locking mechanism for securing the Magic Arm's position. -
Mounting Accessories: Use the 1/4" screws and cold shoe mounts at the ends of the Magic Arm to attach your monitor, LED light, microphone, action camera, or smartphone holder.
Figure 7: Example of a versatile setup with a camera, smartphone, and action camera using the Magic Arm and Super Clamp. Video 1: Product demonstration showing various setup and adjustment possibilities.
5. Maintenance & Storage
- Cleaning: Use a soft, lint-free cloth to clean the product. Do not use harsh chemicals or abrasive materials.
- Storage: Store the product in a dry place at room temperature (15°C - 35°C) when not in use.
6. Troubleshooting & Stop-Use Conditions
If the product does not function as expected, stop using it and check:
- Correct installation or setup of components.
- Compatibility of accessories with the mounting points (e.g., 1/4" screw, cold shoe).
- Ensure all knobs are tightened sufficiently to hold the equipment securely.
- Verify that the total weight of mounted equipment does not exceed the maximum load capacity for the specific model (GM-C1: 5kg, GM-C2/GM-C3: 3kg).
If issues persist, discontinue use and contact customer support.
7. Technical Specifications
| Feature | GM-C1 (Super Clamp) | GM-C2 (Magic Arm) | GM-C3 (Magic Arm) |
|---|---|---|---|
| Material | CNC Aluminum Alloy | ||
| Interface | 1/4" Screw Holes, ARRI Points, Cold Shoe Mounts | 1/4" Screw, Cold Shoe Mount | |
| Max Load | ≈ 5kg | ≈ 3kg | |
| Net Weight | ≈ 116g | ≈ 82g | ≈ 138g |
| Size (L x W x H) | ≈ 67x88mm | ≈ 25x145mm | ≈ 25x220mm |
| Max Opening (Clamp) | 0-70mm | N/A | |
| Capable of Camera Mounting | Yes | ||
| Package | Yes | ||
| Origin | Mainland China | ||
8. User Tips
No specific user tips were available from reviews or Q&A for this product.
9. Warranty & Support
For warranty information, technical support, or service inquiries, please contact the seller or manufacturer directly. Keep your proof of purchase for any warranty claims.
Manufacturer: Shenzhen New Vision Photography Equipment Co., Ltd
Email: ambitful999@163.com
Tel: +86 17603004256
EU Authorized Representative: E-CrossStu GmbH
Email: E-CrossStu@web.de
10. Disposal & Recycling
Do not dispose of this product with general household waste where special disposal rules apply. Follow local environmental and waste disposal regulations for proper recycling.