1. Safety Precautions and Warnings
To avoid injury or damage to the vehicle and/or scan tool, please read this manual at first and observe the following safety precautions when working on a vehicle:
- Always perform vehicle tests in a safe environment.
- Do not attempt to operate or observe the unit while driving a vehicle.
- Operating or observing the device while driving can cause distraction and may result in a fatal accident.
- Wear safety glasses that meet the standards of ANSI.
- Keep your hair, hands, clothing, tools, and test equipment away from all moving or hot engine parts.
- Operate the vehicle in a well-ventilated area: Exhaust fumes are toxic.
- Put the transmission in PARK (for automatic) or NEUTRAL (for manual) and make sure the parking brake is engaged.
- Never leave the vehicle unattended while performing tests.
- Use extreme caution when working near the ignition coil, distributor cap, ignition wires and spark plugs. These components generate dangerous voltages when the engine is running.
- Keep a fire extinguisher nearby that is suitable for gasoline, chemical, and electrical fires.
- Keep the scan tool dry, clean, and free of oil/water or grease. If necessary, use a mild detergent on a clean cloth to wipe the exterior of the scan tool.
2. Product Overview
2.1. Coverage
The OBDMATE OM807 is a professional diagnostic tool designed specifically for Mercedes-Benz vehicles. It supports multiple vehicle systems and offers deep diagnostic capabilities beyond basic OBD2 functions.
This device works on most OBDII compatible American, European, and Asian vehicles after 2000.
It supports most Mercedes-Benz models from 1991-2025, including:
- Mercedes-Benz cars: A-Class, B-Class, C-Class, E-Class, S-Class, AMG GT, CL, CLA, CLC, CLK, CLS, R-Class, SL, SLK/SLC, SLS/SLR, Maybach, EQA/EQB/EQC.
- Mercedes-Benz Sprinter: Commercial vehicle series (W901‑905, W690, W900, W906, W907, W909, W910). Note: Some Sprinter models have a 38PIN diagnostic interface, which is not supported; a 16-PIN OBDII connector is required.
- Other Commercial Vehicles: Vaneo, Vito/Viano/V-Class/Metris (W638, W639, W447, W448), Citan (W415), X-Class (W470, W471).
- Benz Smart: All generations (W450, W451, W452, W453, W454).
Important: Only compatible with vehicles equipped with a 16-PIN OBDII diagnostic connector. Compatibility varies by model and chassis; please confirm before purchase.

Image: Table detailing wide vehicle coverage for Mercedes-Benz Sedan & Compact, Coupe & Performance, SUV & Off-Road, Sports & Luxury & EV, Commercial & Smart models.

Image: Table detailing commercial vehicle and Smart car coverage, including Sprinter, Vito, Citan, X-Class, and Smart models.

Image: Visual representation of Mercedes-Benz, Sprinter, and Smart vehicles, highlighting 7 supported languages: English, French, German, Italian, Spanish, Portuguese, Czech.
2.2. Product Specifications
- Display: 2.8" TFT 262K true color, 320*240 pixels.
- Operating temperature: 0 to 60 °C (32 to 140 °F)
- Storage temperature: -20 to 70 °C (-4 to 158 °F)
- External power supply: 8.0 to 18.0 V (Vehicle battery-powered)
- Dimensions: 166x90x27 mm (L × W × H)
- Net Weight: 0.385 kg
- Communication Interface: OBD-II
- Free Update Period: Lifetime
- Automotive fit type: Vehicle specific fit
- Battery Included: No
- Wireless Support: No
- Software Update: Yes
- Language: English, German, French, Italian, Spanish, Portuguese, Czech
- Certification: CE, FCC, RoHS
2.3. Product Appearance

Image: Front view of the OBDMATE OM807 scanner, displaying its screen and control buttons, with menu options like Diagnose, OBD II, Oil Reset, EPB Reset, BAT, BMS Reset, ETC Reset, DLC PIN Test, and Settings.

Image: Collage showing the 2.8" screen, live data stream, battery test, DLC pin test, and full OBD2 modes of the OM807 scanner.
Button Descriptions
- LCD DISPLAY: Indicates test results. Backlit, 2.8" TFT color screen, 320*240 pixels.
- [F1]/[F2] BUTTON: Shortcut keys for "I/M Readiness", "Diagnose" and "Service" functions.
- [ESC] BUTTON: Cancels the current selection/action or returns to the previous menu.
- [OK] BUTTON: Confirms the current selection/action.
- [▲] BUTTON: Scrolls upward through menu items (one item per press).
- [◀] BUTTON: Moves the cursor left or selects the left menu item.
- [▶] BUTTON: Moves the cursor right or selects the right menu item.
- [▼] BUTTON: Scrolls downward through menu items (one item per press).
- OBDII CONNECTOR: Connects the scan tool to the vehicle's DLC (Data Link Connector).
3. Setup
3.1. OM807 Connection Procedure
- Turn off the ignition.
- Plug the scan tool's 16-pin connector into the vehicle's DLC port.
- Turn the ignition to "ON" position (do not start engine).
- The scan tool will power up automatically.
3.2. Software Upgrade
This product can be updated via USB. We recommend using a PC with the USB method for faster upgrades. You can always get the latest BENZ vehicle diagnostic software and functions without paying additional subscription fees.
Upgrade Steps:
- Visit the official OBDMATE website.
- Connect the OM807 to your laptop using the provided USB-C cable.
- Download and install the update software.
- Follow the on-screen instructions to complete the update.

Image: Diagram illustrating the lifetime free update process: Visit Official Website, Connect OM807 to Laptop, Download & Update.
4. Operating Instructions
The OM807 adopts a plug-and-play design, requiring no Bluetooth pairing or APP installation. Simply connect the OBD connector to your car’s DLC port, and the scanner will automatically identify the VIN and quickly complete vehicle scanning.
4.1. System Diagnose For Benz
This product mainly tests Mercedes-Benz, Sprinter, and Smart vehicles. The following steps use Mercedes-Benz as an example.
- Select "For Benz" from the main menu.
- Then select "Automatically Search (Auto VIN)" from the "Diagnose" menu. The scan tool will display vehicle information such as VIN, year, and model.
Note: "Automatically Search" reads VIN to identify specific models and chassis. Currently, only Mercedes-Benz cars support automatic recognition. Smart and Sprinter do not support Automatic Search.
Note: Diagnostic menu options vary depending on the vehicle model.

Image: Illustration of the OM807 performing a quick scan of all Mercedes-Benz systems, including Chassis, Engine, BMS, Air Steering, Air Conditioning, Airbag, Seat, Parking Brake, TPMS, Suspension, DPF, Transmission, and Headlight.

Image: Icons representing various vehicle systems (Engine, Transmission, ABS, SRS, Steering, Chassis, BMS, EPB, TPMS, DPF, Headlight, Seat, Air Conditioning) that the OM807 can scan.
Manual Selection For Benz
If Auto VIN fails, you can manually select the vehicle. The tool will automatically scan the vehicle's systems, and faulty systems will be displayed in red.
4.2. Read Fault Codes
To read fault codes:
- Select a system (e.g., TCM - Transmission Control Module).
- Select "Read Fault Codes". The tool will display detailed code definitions to guide repair.
4.3. Erase Fault Codes
To clear fault codes:
- Select "Erase Fault Codes".
- Confirm the action.
- Turn off the ignition, wait for about 10 seconds, then switch it back on (without starting the engine).
- Check the instrument panel.

Image: Depicts the OM807 scanner clearing a warning light on a dashboard, showing the 'Before' state with multiple warning lights and the 'After' state with lights cleared.
4.4. Read Data Stream
To view real-time data:
- Select "Read Datastream" from the menu.
- Choose "View All Items" to see all retrieved data, including values (volts, rpm, temperature, speed, etc.) and system status information (open loop, closed loop, fuel system status, etc.).
- Alternatively, select "Select Items" to choose specific data points.
- Use the arrow keys to navigate and [OK] to zoom in. Press [F1] to view the trend curve.
4.5. Special Functions For Benz (15+ Reset Services)
The OM807 offers over 15 commonly used maintenance special functions, all unlocked directly with no extra fees. These functions allow you to handle daily maintenance tasks at home, saving on dealership fees.
Note: Special functions availability depends on the vehicle's year, make, and model. Not all special functions are supported.

Image: Grid of icons representing 15+ reset services including Oil Reset, TPS Throttle Adaptation, Battery Registration, Brake Pad Replace, SAS Reset, TCM Adaptations, TPMS Reset, EGR Actuator Teach In, ABS Bleeding, DPF Regeneration, AdBlue Fill Level Reset, IQA Injector Coding, Fuel Pump Activation, Differential Pressure Sensor Replacement.

Image: Icons representing various maintenance functions the OM807 can perform, such as Oil Reset, SAS Reset, Battery Registration, TPMS Reset, TPS Throttle Adaptation, ABS Bleeding, Brake Pad Replace, EGR Actuator Teach In, AdBlue Fill Level Reset, DPF Regeneration, Fuel Pump Activation, IQA Injector Coding, and TCM Adaptations.
Oil Reset
To perform an Oil Reset:
- Select "Special Functions" then "Oil Reset".
- Follow the on-screen prompts to confirm and complete the reset.
Electronic Parking Brake (EPB) Reset
To perform an EPB Reset:
- Select "Special Functions" then "Electronic Parking Brake".
- Follow the on-screen prompts, ensuring the vehicle is at a standstill, secured, and the parking brake is released.
Functions for Diesel Engines
For Mercedes diesel cars, the OM807 supports:
- DPF Regeneration
- AdBlue Reset
- Fuel Pump AdBlue Reset
- Pressure Sensor Replacement
- Pressure Valve Replacement

Image: Shows advanced special functions for diesel engines, including DPF Regeneration, AdBlue Reset, Fuel Pump AdBlue Reset, Pressure Sensor Replacement, and Pressure Valve Replacement.
4.6. DLC PIN Test
The tool supports voltage measurement detection for each pin of the 16-pin diagnostic link connector (DLC).
- Select "DLC PIN test" from the main menu.
- Press [OK] to proceed. The test results will be displayed on the screen.
4.7. Full OBDII Functions
The OM807 is also a universal OBD2 code reader for all cars after 1996 that come with the OBD2 protocol. It supports all essential OBD2 functions.

Image: Depicts the OM807 performing a Smog Test, showing the scanner screen with I/M Readiness status and a car emitting exhaust fumes.
Read Codes
Access "OBDII", select "Read Codes" from "diagnostic menu" and press [OK]. If fault codes exist, they will be listed.
Erase Codes
Select "Erase Codes" in the diagnostic menu. Confirm to clear/reset emissions-related diagnostic information.
I/M Readiness
Select "I/M Readiness" in the diagnostic menu to check the status of various monitors (Misfire, Fuel System, Comprehensive Component, Catalyst, Heated Catalyst).
Freeze Frame
Select "Freeze Frame" in the diagnostic menu then press [OK]. The screen will display recorded emission-related fault information.
O2 Sensor Test
Select "O2 sensor test" in the diagnostic menu then press [OK]. It will retrieve and display the O2 Sensor monitor test results from the vehicle's ECU.
On-board Monitoring
Select "On-board monitoring" in the diagnostic menu then press [OK]. It will display the results of the on-board diagnostic monitoring (the data is different each time).
EVAP System Test
Select "EVAP system test" in the diagnostic menu then press [OK]. If the vehicle supports this function, it will display the evaporative system leak test status.
Vehicle Information
Select "Vehicle information" in the diagnostic menu then press [OK]. It will display information such as VIN (Vehicle Identification Number), CID (Calibration Identifications), CIN (Calibration Verification Numbers), etc.
4.8. BAT Check (Battery Test)
To perform a battery test:
- Select "BAT" from the main menu. This monitors the vehicle's battery voltage in real time.
- To perform a cranking test, turn off the engine and press [OK] to start detection. The device will display current voltage and a voltage graph during cranking.
4.9. Tool Setup
The scan tool allows you to make the following settings and adjustments:
- Language: Select your preferred language (English, German, French, Italian, Spanish, Portuguese, Czech).
- Beeper: Turns ON/OFF the beep tone.
- Unit of measurement: Choose between Imperial (e.g., mph, °F) or Metric (e.g., km/h, °C).
- Background: Select Day mode or Night mode.
- Edit the function of shortcut key F1/F2: Set F1/F2 as shortcut for "I/M Readiness", "Diagnose" or "Service".
- Device information: Access version information about this tool.
5. Maintenance
Regular maintenance of your OM807 scanner ensures its longevity and optimal performance.
- Keep the scan tool dry, clean, and free of oil/water or grease.
- If necessary, use a mild detergent on a clean cloth to wipe the exterior of the scan tool.
- Perform regular software updates to ensure compatibility with the latest vehicle models and access new features.
6. Troubleshooting
If you encounter issues, refer to the following common solutions:
- No Power: Ensure the 16-pin OBDII connector is securely plugged into the vehicle's DLC port and the ignition is in the "ON" position (engine off).
- Communication Error: Verify the vehicle's compatibility (16-pin OBDII connector, Mercedes-Benz group vehicles within supported years). Try manually selecting the vehicle model if Auto VIN fails.
- Fault Codes Not Clearing: Ensure there are no underlying hardware faults that require physical repair before codes can be cleared. Follow the exact procedure for clearing codes, including cycling the ignition.
- Specific Functions Not Available: Feature availability may vary depending on your vehicle's year, make, and model. Not all special functions are supported on all vehicles.
- Software Issues: Perform a software update to ensure you have the latest version, which may resolve bugs or add new functionalities.
7. User Tips
- Contact Support for Missing Functions: If you find specific functions like MAF or throttle body adaptation are missing for your model, contact OBDMATE customer service. They have been known to add these options through software updates.
- Broad Compatibility: The OM807 is effective for reading and resetting fault codes on Mercedes-Benz models from at least 2011 onwards, including comprehensive monitoring functions.
- Quality Build: Users appreciate the robust build quality and the long cable, which makes it easier to use in various vehicle setups.
- Check for Specific Function Limitations: Be aware that some very specific functions, like resetting an analog clock in the cluster dashboard control, might not be supported.
- No Coding Support: This tool is primarily for diagnostics and resets; it does not support advanced coding functions.
8. Frequently Asked Questions (FAQ)
- Q: Can this OM807 scanner perform full system diagnosis on Mercedes-Benz vehicles, including ABS, SRS Airbag, ESP, and transmission fault codes?
- A: Yes, the OM807 is a professional Mercedes-dedicated full-system diagnostic tool. It supports reading and erasing fault codes for nearly all vehicle modules, including Engine, ABS braking system, SRS airbag, ESP stability control, automatic transmission, body control module, instrument cluster, central locking, and climate control on Mercedes & Smart vehicles.
- Q: Does this device support Mercedes service reset / oil light reset after an oil change?
- A: Absolutely. It covers mainstream service reset functions for Mercedes & Smart, such as engine oil service reminder reset, inspection service reset, brake pad wear light reset, and cabin/air filter service reset. You can easily reset the dashboard service reminder after maintenance.
- Q: Is it fully compatible with all Smart Fortwo / Forfour / Roadster models for a full-system check?
- A: Yes, it offers full compatibility for all generations of Smart microcars: Smart 450, 451, 452 Roadster, W454 Forfour, and 453. It can access all Smart control modules, read fault codes, and perform service resets and special functions with diagnostic depth similar to original garage equipment.
- Q: Can I use it for Mercedes commercial vans like Sprinter, Vito, V-Class, and Citan?
- A: Yes, designed specifically for Mercedes-Benz group vehicles, it fully supports Sprinter, Vaneo, Vito, Viano, V-Class, and Citan commercial vans and MPVs. It can perform full system diagnostics, service resets, and special function operations for these vehicles.
- Q: Does it have language options for French, German, Spanish, and Italian for European users?
- A: Yes, it comes pre-installed with 7 European mainstream languages: English, French, German, Italian, Spanish, Portuguese, and Czech. You can switch the menu language directly on the device settings page without extra installation.
- Q: Do I have to pay annual fees for software updates? Is the vehicle database update free forever?
- A: No, there are no annual subscriptions or hidden charges. We provide lifetime free updates for the vehicle database, diagnostic software, and device performance.
- Q: Will it work on a 1998 Mercedes CLK 320?
- A: This vehicle is not currently supported because the OBD communication protocol is incompatible.
- Q: Can it code a new battery to the car and reset the oil service light?
- A: Yes, this device supports battery matching/registration and maintenance resets, including the oil service light.
- Q: Does it deactivate the limp mode of a 2004 E320 model?
- A: The OM807 does not allow you to deactivate "Limp Mode." When "Limp Mode" is activated, it indicates a fault in the engine or gearbox that limits vehicle speed, requiring repair. It is recommended to take it to a specialized Mercedes-Benz workshop for repair.
- Q: Can we access the Airmatic (air suspension) parameters on a W164?
- A: This device currently does not support Airmatic (air suspension) functionality tests or special functions.
- Q: Is this scanner suitable for all vehicles?
- A: This model is exclusively for Mercedes-Benz vehicles. If you are looking for a product suitable for all vehicles, we recommend purchasing the OM901 model.
- Q: Can this model read and fix SRS faults?
- A: Yes, this model is suitable for Mercedes-Benz vehicles and supports comprehensive system diagnostics, including the SRS system.
- Q: Is it compatible with Fuso Canter 2016+?
- A: Your car model is not supported.
- Q: Can you program the optics?
- A: Our instruments do not currently support the programming function.
- Q: Can this scanner read Mercedes TCM codes?
- A: Yes, it supports reading and clearing transmission control module (TCM) codes for compatible Mercedes-Benz vehicles.
9. Warranty and Support
9.1. Warranty
- This warranty is valid solely for the original purchaser of OBDMATE products.
- OBDMATE products are warranted against defects in materials and workmanship under normal use for one year (12 months) from the date of retail purchase.
- If any issues, we commit to providing a resolution within 24 hours.
9.2. Contact Us
- Email: support@obdmate.com
- Website: https://www.obdmate.com
9.3. Trademarks and Copyright
- OBDMATE is the trademark of AUTOPHIX TECH CO.,LTD. All other marks are trademarks or registered trademarks of their respective holders.
- © 2025 AUTOPHIX TECH. All rights reserved.
9.4. Disclaimer
The information, specifications, and illustrations contained in this documentation are provided for informational purposes only and reflect the product status at the time of publication. OBDMATE expressly reserves the right to modify, improve, or discontinue any product or service described herein without prior notice or obligation.
10. Accessories List

Image: Contents of the OM807 package, including the OM807 Car Scanner, Nylon Carrying Case, Upgrade Guide, USB-Type C Cable, and User Manual.

Image: Detailed view of the OM807 package contents, including the scanner, carrying case, USB-C cable, user manual, and upgrade guide.
The OM807 diagnostic scanner comes with complete matching accessories, equipped with a durable nylon storage case for convenient carrying and safe storage.
- OM807 Multi-system Car Diagnostic Scanner
- Nylon Carrying Case
- USB-C Upgrade Cable (for firmware update)
- Official User Manual
- Upgrade Operation Guide