1. Product Overview
The VDIAGTOOL VD31 is a multifunctional car diagnostic tool designed for both professionals and DIY enthusiasts. It combines a car engine fault code reader, key battery tester, and car battery voltage tester into one compact device. The VD31 offers comprehensive OBD2 functions, real-time data graphing, DTC lookup, and I/M readiness checks to simplify vehicle maintenance and diagnostics.
Key Features:
- Full OBD2 Functions (Read/Clear DTCs, Live Data, Freeze Frame, O2 Sensor Test, etc.)
- Key Fob Battery Testing
- Car Battery Voltage Monitoring
- One-Click I/M Readiness (Smog Check)
- Built-in 100,000+ DTC Lookup Library
- 4-in-1 Live Data Graphing
- Data Playback & Print Support
- Multi-language Support (8 languages)
What's in the Box:
- VDIAGTOOL VD31 Code Reader
- Type-C Cable (for computer connection and firmware updates)
- User Manual

Figure 1: VDIAGTOOL VD31 OBD2 Scanner
2. Safety Information
To ensure your safety and prevent damage to the device or vehicle, please carefully read and follow all instructions in this manual before use. When operating the device, always verify proper testing procedures and strictly adhere to the instructions provided. As automotive electrical systems may vary, you must assess potential risks and ensure a safe testing environment.
Always observe all safety warnings, use appropriate tools, and disconnect power sources when necessary. Improper operation may result in personal injury, equipment damage, or voided warranty.
Safety Messages:
Safety messages use standardized signal words to indicate hazard levels and prevent injuries or equipment damage:
DANGER: Will result in death or serious injury if ignored. Indicates an immediately life-threatening hazard.
WARNING: Could result in death or serious injury if ignored. Indicates a potentially dangerous situation.
Safety Instructions:
- Always ventilate the service area when the engine is running or use a building exhaust removal system if available. Carbon monoxide is odorless and deadly.
- Always conduct testing in a safe, controlled environment.
- Wear ANSI-approved safety goggles during all operations.
- Keep all objects away from moving or hot engine components.
- Ensure proper ventilation to avoid toxic exhaust fumes.
- Secure the vehicle in PARK (automatic) or NEUTRAL (manual) with the parking brake engaged.
- Place wheel chocks and never leave the vehicle unattended during tests.
- Exercise extreme caution around ignition systems – hazardous voltages are present.
- Maintain an ABC-rated fire extinguisher within immediate reach.
- Never connect/disconnect test equipment with ignition on or engine running.
- Keep all test equipment clean, dry, and free from contaminants.
- Never operate test equipment while driving – focus solely on testing.
- Strictly follow the vehicle service manual's diagnostic procedures.
- Verify full battery charge and secure DLC connections before testing.
- Never place test equipment near the distributor due to EMI risks.
3. Technical Specifications
| Feature | Specification |
|---|---|
| Display | 2.8-inch TFT Color Screen |
| Communication Interface | OBD-II |
| Operating Temperature | 0°C to 60°C (32°F to 140°F) |
| Storage Temperature | -20°C to 70°C (-4°F to 158°F) |
| Connection | Wired via main cable |
| Power Source | OBDII port connection, Type-C cable, or built-in 9V battery |
| Compatibility | OBDII & EOBD (12V) vehicles (1996+ US, 2002+ EU, 2008+ Asia) |
| Supported Protocols | KWP2000, ISO2000, ISO9141, J1850VPW |
| Dimensions | 6.5 x 3.54 x 1.18 inches |
| Weight | 8.47 oz |
| Free Update Period | Lifetime |
| Battery Included | No (requires 9V battery for key battery check only) |
| Wireless Support | Wifi (for updates/data transfer, not for vehicle communication) |
| Languages | English, Chinese, French, Spanish, German, Russian, Italian, Polish |
| Memory | 32G |

Figure 2: Extensive OBD2 Protocol Compatibility

Figure 3: Wide Vehicle Compatibility and Language Support
4. Getting Started & Setup
Power on your code reader by connecting to vehicle power or a computer before using any applications.
4.1 Power Connection Methods:
Vehicle Power Connection (Recommended):
- Locate the vehicle's DLC (Data Link Connector), typically under the dashboard.
- With ignition ON, connect the code reader to the DLC.
- The device will auto-power on.
Important:
- Never use Type-C power during vehicle communication.
- Ensure clean connector contact.
Computer Connection (For Updates/Data Transfer):
- Connect the Type-C cable to the device and computer.
- The device will auto-power on.
Built-in 9V Battery (For Key Battery Check Only):
- Insert a fresh 9V battery into the compartment.
- The device will auto-power on when the battery is installed.
4.2 Location of the Data Link Connector (DLC):
The Data Link Connector (DLC), also known as the Diagnostic Link Connector, is a standardized 16-pin port used to connect diagnostic scan tools to the vehicle's onboard computer.
Typical DLC Locations:
- Most vehicles: Within 12 inches of the dashboard center, typically under or near the driver's side.
- Some Asian/European models: Behind the ashtray (may require removal for access).
- If not visible: Check for a location label or consult the vehicle's service manual.
5. Operating the Code Reader
5.1 Device Button Layout Explained:

Figure 4: VDIAGTOOL VD31 Device Button Layout
- 2.8 Inch LCD Screen: Displays all information.
- Up Button: Menu navigation up; previous page in multi-screen info; edits DTC characters.
- Shutdown Button: Short press to power on; long press (3s) to power off.
- Right Button: Next page in multi-screen info.
- Key Battery Button: Direct access to key battery voltage measurement.
- Down Button: Menu navigation down; next page in multi-screen info; edits DTC characters.
- I/M Button: Checks emissions readiness and drive cycle status.
- Left Button: Previous page in multi-screen info.
- ESC Button: Returns to the previous screen (press once to exit other tests).
- LED For Different DTC Types: Visual indicators for diagnostic trouble codes.
- OK Button: Confirms selection.
5.2 Application Overview:
Upon startup, you'll see these preloaded applications on the home screen:
- OBDII/EOBD: Accesses all nine OBD system tests.
- Battery: Tests and displays the voltage of the vehicle battery.
- Key Battery: Tests and displays the vehicle key fob battery level.
- DTC Lookup: Provides access to the diagnostic trouble code lookup library.
- Review: Accesses tested data files.
- Print: Accesses the printing function.
- Setting: Modifies device settings (Language, Unit of Measure, etc.).

Figure 5: VD31 Main Menu Screen
5.3 OBDII/EOBD Functions:
When you select the OBDII/EOBD application, your vehicle's diagnostic information will display. Press OK to access the diagnostic menu with these available tests:
- Read DTC
- Clear DTC
- Live Data
- Freeze Frame
- MIL Status
- Vehicle Info
- O2 Sensor
- Mode 6 (On-Board Monitoring)
- Mode 8 (EVAP System Test)

Figure 6: Full OBD2 Functions Overview
5.3.1 Read DTC (Diagnostic Trouble Codes):
This function allows you to check stored fault codes in the vehicle's control modules.
- Stored DTCs: Active fault codes confirmed by the ECU, typically illuminating the Check Engine Light (MIL).
- Pending DTCs: Temporary fault codes indicating a potential issue, not yet confirmed. They may become stored DTCs if the problem recurs.
- Permanent DTCs: Fault codes that remain stored even after the MIL turns off, indicating a significant issue that requires repair. They clear only after the underlying issue is fixed and the system completes 3 consecutive drive cycles without detecting the fault.
- Record DTC: Allows you to record the DTCs if there are trouble codes in the vehicle.
To read codes: Select