1. Introduction
Thank you for choosing the AUXBEAM 8Gang Knob RGB Switch Panel. This manual provides essential information for the safe and effective installation, operation, and maintenance of your new switch panel. Please read all instructions carefully before use to ensure proper functionality and to prevent damage or injury.
This product is designed for controlling various electrical accessories in automobiles, trucks, ATVs, and UTVs, offering advanced features like RGB backlighting, multiple lighting modes, and external trigger synchronization.
2. Safety & Warnings
Important Safety Information:
- Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.
- Keep the device and its cord out of reach of children under 3 years old.
- Keep away from children unless supervised by an adult.
- Do not use this product for purposes other than its intended use.
- Inspect the product before each use; do not use if damaged.
- Follow installation and operation guidelines to avoid injury.
- Electrical Products: Do not expose to water or moisture.
- Sharp/Dangerous Goods: Handle with care to avoid cuts or injuries.
- Installation environment shall be clean, dry, and free of oil, dust, and dirt.
- Inspect the product for any deformation, crack, damage, or rust before installation.
- Use qualified tools and fasten to standard torque; do not install by force.
- Parts involving electrical, fuel, brake, steering, and transmission systems must be installed by professional technicians.
- Disconnect the negative battery terminal before installation to avoid short circuits.
3. Product Features
- **120A All-Solid-State Load System:** Features a 3×30A + 4×20A + 1×10A output configuration, offering a total capacity of 120A. Built with high-performance solid-state relays for safe and reliable operation.
- **One-Touch All Lights Sync (Toggle/Strobe/Chase):** Instantly activate all 8 connected devices in constant-on (Toggle), high-visibility strobe (Strobe), or dynamic chasing light effects (Chase).
- **Master Dimming:** Precise dimming of individual work lights, synchronized management of multiple lighting systems, or fine control of fan speeds.
- **Four External Triggers:** Enables seamless automation with your vehicle's factory signals, syncing with high beams, reverse, brake warnings, and hazard signals.
- **DRL Auto-Start:** Connect to the 0-Terminal for lights to turn on automatically with ACC Ignition.
- **Four Modes:** Toggle (constant light), Momentary (flexible momentary), Pulsed (emergency strobe), and SOS (standard SOS signal).
- **Color-Changing Panel:** Rotary knob panel with adjustable RGB backlighting for personalized style and brightness control.
- **Optional Wireless Remote:** Extend control range up to 200 feet for exterior lighting, camp lighting, and more.
4. Specifications
| Attribute | Value |
|---|---|
| Product Name | Parts for Automobiles & Motorcycles |
| Model | KS-80 |
| Voltage Input | DC 12-24V |
| Max Current | 120A |
| Rated Current | 100A |
| Rated Voltage | 12V 20A / 24V 10A |
| Max Power | 1200W/12V, 2400W/24V |
| Waterproof Rating | IP65 |
| Operating Temperature | -40°C ~105℃ / -40℉~221℉ |
| External Testing Certification | CE |
| Mounting Type | Others |
| Switch Type | Multi-function mechanical |
| Is It Charged | Yes |
| Origin | Mainland China |
| Item Type | Switch panel |
5. Package Contents
The package includes the following components:
- 1 x KS-80 Knob Switch Panel
- 1 x Circuit Box
- 1 x 100A Circuit Breaker
- 160 pcs Labels
- Mounting Brackets
- 1 x KS-80 Installation Manual (PDF available online)
- 1 x 10ft Wire Harness
- Power Harness & Connections
- Acrylic Double-Sided Tape
- 1 x KS-80 Package Box
- External Trigger Wire
- 1 x Remote Controller (OPTIONAL)
- 1 x 3.94FT Extension Cable (OPTIONAL)
- 1 x 20FT Extension Cable (OPTIONAL)
6. Installation
Before beginning installation, ensure you have read and understood all safety warnings. Professional installation is recommended for parts involving complex vehicle systems.
6.1 Pre-Installation Checklist
- Ensure the installation environment is clean, dry, and free of oil, dust, and dirt.
- Inspect all product components for any deformation, cracks, damage, or rust. Do not install if damaged.
- Gather all necessary tools. Use qualified tools and fasten to standard torque.
- **Crucially, disconnect the negative battery terminal of your vehicle before starting any electrical work to prevent short circuits.**
6.2 Wiring the Switch Panel and Circuit Box
The KS-80 switch panel controls up to 8 different electrical equipment. Connect your accessories to the designated output terminals on the circuit box. The circuit box connects to your vehicle's battery and the switch panel.
6.3 DRL Auto-Start Connection
For automatic Daytime Running Light (DRL) functionality, connect the DRL wire to the 0-Terminal. This will ensure your lights turn on with the ACC ignition.
6.4 External Trigger Setup
The KS-80 supports four external triggers for automated lighting responses. These triggers allow synchronization with your vehicle's existing signals:
- **High Beam Sync:** Connect to your vehicle's high beam signal to illuminate additional lights when high beams are active.
- **Reverse Assist:** Connect to your vehicle's reverse signal to activate auxiliary lights when shifting into reverse.
- **Brake Alert:** Connect to your vehicle's brake signal to amplify brake warnings with additional lighting.
- **Hazard Sync:** Connect to your vehicle's hazard signal to synchronize all lighting for total perimeter alert.
7. Operation
The AUXBEAM KS-80 switch panel offers intuitive control over your vehicle's accessories.
7.1 Basic On/Off Control
Each of the 8 buttons on the panel controls a connected device. Press a button once to turn the corresponding device ON. Press it again to turn it OFF. The LED indicator above each button will light up when the circuit is active.
7.2 Lighting Modes
The KS-80 features four distinct lighting modes, accessible via dedicated buttons:
- **Toggle (Constant Light):** Press the "Toggle" button once for stable, constant illumination from all connected devices.
- **Momentary (Flexible Momentary):** Press the "Momentary" button for temporary activation of devices.
- **Pulsed (Strobe Mode):** Tap the "Strobe" button to switch all connected devices to a high-visibility strobe mode for emergencies or warnings.
- **SOS (Distress Signal):** Press the "SOS" button to activate a standard SOS distress signal.
7.3 Master Dimming and Backlight Adjustment
Use the rotary knob to adjust the brightness of connected lights. The panel also features adjustable RGB backlighting, allowing you to customize the color and brightness to match your vehicle's interior ambiance.
7.4 One-Touch All Light Sync (Chase Mode)
Press the "Chase" button to configure 2 to 8 devices for dynamic chasing light effects, creating personalized lighting patterns.
7.5 Optional Wireless Remote Control
If you have the optional wireless remote, it allows you to control your accessories from up to 200 feet away, ideal for external lighting or camp setups.
8. Maintenance
- **Cleaning:** Wipe the switch panel and circuit box with a soft, dry cloth. Avoid using harsh chemicals or abrasive cleaners.
- **Inspection:** Periodically inspect all wiring and connections for signs of wear, corrosion, or damage. Ensure all connections are secure.
- **Environmental Protection:** Although the product has an IP65 waterproof rating, avoid prolonged exposure to extreme moisture or direct water jets to maximize lifespan.
- **Thermal Management:** Ensure the circuit box has adequate ventilation to prevent overheating, especially during heavy load usage.
9. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Panel not powering on | Loose power connection, blown fuse, incorrect wiring. | Check battery connections. Inspect the 100A circuit breaker and other fuses. Verify wiring against the installation diagrams. |
| Individual accessory not working | Loose accessory connection, faulty accessory, incorrect output wiring. | Ensure the accessory is properly connected to its output terminal. Test the accessory directly if possible. Check the specific output wiring. |
| External trigger not functioning | Incorrect trigger wire connection, vehicle signal issue. | Verify the external trigger wire is correctly connected to the corresponding vehicle signal. Ensure the vehicle signal is active. |
| Remote control not working | Dead batteries, out of range, interference. | Replace remote batteries. Ensure you are within the 200ft range. Minimize potential signal interference. |
10. User Tips
- **Labeling:** Utilize the provided 160 pcs labels to clearly mark each switch for quick identification of connected accessories.
- **Customization:** Experiment with the RGB backlight colors and brightness to find the perfect aesthetic for your vehicle's interior.
- **Safety First:** Always double-check your wiring and connections before restoring power to the vehicle.
- **Power Management:** Be mindful of the total current draw of your accessories to stay within the 120A maximum capacity of the system.
11. Warranty & Support
The AUXBEAM KS-80 switch panel comes with a 3-year official warranty, backed by our professional support team. For any inquiries or support needs, please contact:
- **Manufacturer:** Changsha zhihuan e-commerce co., ltd
- **EU Authorized Representative:** GAVIMOSA CONSULTORIA, SOCIEDAD LIMITADA
- **Email:** compliance.gavimosa@outlook.com
- **Phone:** 34-88185858
For a complete digital version of the user manual, please refer to the official PDF document referenced as "Item guides & documents" on the product page.