1. Introduction
Thank you for choosing the Heimerdinger LB340 Brushless Rebar Tying Machine. This manual provides essential information for the safe and efficient operation, maintenance, and troubleshooting of your tool. Please read this manual carefully before use and keep it for future reference.
Video: Demonstration of the Heimerdinger LB340 Rebar Tying Machine in action, showing wire loading, tying process, and internal mechanisms.
2. Safety Warnings
Always observe basic safety precautions to reduce the risk of fire, electric shock, and personal injury.
2.1 General Power Tool Safety Warnings
- Work Area Safety: Keep work area clean and well-lit. Do not operate power tools in explosive atmospheres. Keep children and bystanders away.
- Electrical Safety: Power tool plugs must match the outlet. Avoid body contact with grounded surfaces. Do not expose power tools to rain or wet conditions. Do not abuse the cord. Use an extension cord suitable for outdoor use when operating outdoors. Use an RCD for damp locations.
- Personal Safety: Stay alert and use common sense. Do not operate while tired or under the influence. Dress properly. Use personal protective equipment like safety goggles.
2.2 Specific Safety Warnings for Automatic Rebar Tying Machine
- WARNING: To avoid accidents, always disconnect the Battery Pack from the tool before cleaning or performing any maintenance.
- WARNING: Do not point the tool towards yourself or anyone nearby. Unexpected triggering will discharge the fastener causing an injury.
- Never point the tool at yourself or others. Keep hands and feet away from the tool head.
- Do not load binding wire while the tool is powered on.
- Do not operate the tool with the wire reel cover open.
- Before starting work, always check that the diameter of the rebar to be tied is within the tool's tying capacity.
- Wear close-fitting clothing without loose ends or sleeves.
- If any abnormality is detected, stop using the tool immediately.
- When installing the battery pack, always lock the switch trigger and keep your fingers off the trigger.
- When tying rebar, take care not to move them.
- Do not touch the binding wire during the tying process.
2.3 Battery-Powered Tool Use and Precautions
- Charge the battery only with the charger specified by the manufacturer.
- Use the power tool only with specifically designated battery packs.
- When the battery pack is not in use, keep it away from metal objects that could bridge the terminals.
- Under abusive conditions, liquid may be ejected from the battery. Avoid contact.
- Do not use damaged or modified battery packs or tools.
- Do not expose the battery pack to fire or excessive temperatures.
- Follow all charging instructions.
2.4 Charger Safety Instructions
- Charge only rechargeable batteries.
- Non-rechargeable batteries cannot be charged.
- Use a power source with the specified voltage.
- Do not charge in the presence of flammable liquids or gases.
- Do not expose charger to rain or snow.
- Never carry charger by cord or yank it to disconnect.
- Unplug the charger after charging or before maintenance.
- Ensure cord is located safely.
- Do not operate charger with damaged cord or plug.
- Do not operate or disassemble charger if damaged.
- Charger is not intended for use by young children or infirm persons without supervision.
- Do not charge battery cartridge when temperature is below 10°C (50°F) or above 40°C (104°F).
3. Package Contents
The Heimerdinger LB340 Brushless Rebar Tying Machine is available in several configurations. Please check your specific package contents:
- Option 1: No Battery, No Charger
- 1x LB340 Brushless Rebar Tying Machine
Option 1: Machine only.
- Option 2: One 18V 2A Battery, One Charger
- 1x LB340 Brushless Rebar Tying Machine
- 1x 18V 2A Battery
- 1x Charger
Option 2: Machine with one 2A battery and charger.
- Option 3: One 18V 4A Battery, One Charger
- 1x LB340 Brushless Rebar Tying Machine
- 1x 18V 4A Battery
- 1x Charger
Option 3: Machine with one 4A battery and charger.
- Option 4: One 18V 6A Battery, One Charger
- 1x LB340 Brushless Rebar Tying Machine
- 1x 18V 6A Battery
- 1x Charger
Option 4: Machine with one 6A battery and charger.
- Option 5: Two 18V 2A Batteries, One Charger
- 1x LB340 Brushless Rebar Tying Machine
- 2x 18V 2A Batteries
- 1x Charger
Option 5: Machine with two 2A batteries and charger.
- Option 6: Two 18V 4A Batteries, One Charger
- 1x LB340 Brushless Rebar Tying Machine
- 2x 18V 4A Batteries
- 1x Charger
Option 6: Machine with two 4A batteries and charger.
- Option 7: Two 18V 6A Batteries, One Charger
- 1x LB340 Brushless Rebar Tying Machine
- 2x 18V 6A Batteries
- 1x Charger
Option 7: Machine with two 6A batteries and charger.
4. Specifications
| Feature | Specification |
|---|---|
| Model | LB340 |
| Motor Type | Brushless |
| Voltage | DC18-21V |
| Power | 150W |
| Binding Range | 8-34mm |
| Wire Diameter | 0.8mm |

Image: Heimerdinger LB340 Rebar Tying Machine highlighting key features.
5. Setup
5.1 Installing or Removing Battery Cartridge
To Remove: Press the button on the front side of the battery pack while pulling it out of the tool.
To Install: Align the tongue on the battery pack with the groove on the tool housing, then push in and slide it into place until it locks with an audible click. Ensure the red indicator on the button is not visible after insertion.

Image: Battery cartridge installation/removal.
5.2 Loading the Binding Wire (Wire Reel)
Note: Use of non-genuine Heimerdinger binding wire may cause tool malfunction.
- Locate the knob (Fig. 1). Grasp the knob and turn it counterclockwise. Lift the Wire Coil Cover upward to expose the wire reel compartment.
- Remove the wire spool and cut the binding strap (ensure the wire is not knotted or bent). Straighten approximately 10 cm of the wire end.
- Confirm the correct orientation of the wire reel and carefully place it into the reel compartment in a vertically downward direction (Fig. 2).
- After confirming the reel is correctly oriented, press the latch button (Fig. 3) to ensure the reel securely engages.
- Insert the straightened wire end into the wire guide tube and push the wire forward until it cannot advance further. To verify, press the clutch button (Fig. 4) and continue pushing the wire forward slightly until the gears fully grip the wire.

Fig. 1: Knob & Cover.

Fig. 2: Wire Coil.

Fig. 3: Latch Button.

Fig. 4: Clutch.

Fig. 5: Wire Path.
After the wire reel is installed, close the wire coil cover.
6. Operating Instructions
6.1 Main Power Switch
Press the power button to turn on the tool; the battery charge indicator light will illuminate. Press the power button again to turn off the tool.

Image: Power Switch and Indicator.
6.2 Switch Operation (Trigger Lock)
To prevent accidental activation, the tool has a trigger lock button. To start, slide the trigger lock button to the