HXCONTROLLER MPPT Solar Charge Controller

Contents

HXCONTROLLER MPPT Solar Charge Controller

User Manual

1. Product Overview

The HXCONTROLLER MPPT Solar Charge Controller is a smart Maximum Power Point Tracking (MPPT) charge controller designed for off-grid solar systems. It supports multiple battery types, offers real-time monitoring, and allows remote control via a mobile application using built-in Wi-Fi (ESP32 RainMaker).

Front, back, and angled views of the HXCONTROLLER MPPT Solar Charge Controller

Figure 1: HXCONTROLLER MPPT Solar Charge Controller Views

2. Features

  • Advanced MPPT Technology: Dynamically tracks the Maximum Power Point (MPP) in real-time to maximize energy harvesting from solar panels, even in varying weather conditions.
  • Wide Voltage Range: Supports a maximum PV input voltage of 250VDC, allowing for more solar panels to be connected in series.
  • Built-in Wi-Fi & Smart App: Integrated Wi-Fi for monitoring and control via the ESP RainMaker App (iOS/Android). No additional modules are required.
  • Universal Battery Support: Compatible with 12V–120V battery systems, including Lead-Acid (Flooded, AGM, Gel) and Lithium (LiFePO4, Li-ion) batteries.
  • Multi-Stage Charging: Features Bulk, Absorption, and Float charging stages to optimize battery health and prolong lifespan.
  • Industrial-Grade Protection: Includes over-voltage, over-current, over-temperature, short circuit, reverse polarity, and undervoltage protection.
  • Cumulative Energy Logging: Tracks and logs cumulative energy generation.
  • LCD Display with Key Navigation: Intuitive LCD screen for local monitoring and settings adjustment.
MPPT Solar Charge Controller with internal circuit board visible

Figure 2: Internal Components of the MPPT Solar Charge Controller

3. Setup and Installation

3.1. Safety Clearances

Observe the following safety clearances to ensure no other equipment or objects are within these specified areas, allowing sufficient space for heat dissipation:

  • Left/Right: 20 cm
  • Above: 30 cm
  • Below: 30 cm
Wiring diagram for a solar system including Photovoltaic Module, Switch, Fuse, Inverter, Battery, DC Load, and the MPPT controller

Figure 3: General Solar System Wiring Diagram

3.2. Wiring Sequence

The correct wiring sequence for the solar charge controller is crucial to avoid damage. Please follow these steps carefully:

  1. Connect DC Loads: Connect DC loads to the Load output terminals (optional).
  2. Connect Batteries: Connect batteries to the Battery terminals.
  3. Connect Solar Panels: Connect solar panels to the PV input terminals.
  4. Ensure Correct Polarity: Double-check all connections for correct polarity before powering on.

Important: If connecting loads with large input capacitors (e.g., inverters, DC motors), it is preferred to connect the load before powering the system.

Video 1: Demonstration of controller wiring and menu navigation.

3.3. PV Panel Input Voltage

Minimum Input: Must be 20V higher than the battery's maximum voltage; Maximum Input: 250V.

Diagram showing MAX 250V VOC INPUT with 5 solar panels in series (5pcs 550w solar panel in series)

Figure 4: Max 250V VOC Input for Solar Panels

3.4. General Installation Guidelines

  • Installation should only be performed by qualified personnel.
  • Do not exceed rated voltage/current limits.
  • Keep the unit in a dry and well-ventilated area.
  • Disconnect power before performing any maintenance.

4. Operating Instructions

4.1. Initial Power-Up

Once the battery is connected, the system will power on automatically. The LCD will display the system status. By default, the controller runs in Auto mode and attempts to recognize the battery voltage automatically.

Close-up of the controller's LCD screen showing PV Monitor data

Figure 5: Controller LCD Screen - PV Monitor

4.2. Menu Navigation

The controller features a 4-key interface for navigation:

  • MENU: Long press to enter the main menu. Also acts as a confirmation key.
  • UP/DOWN: Navigate through menu options.
  • BACK: Exit the current menu or return to the previous screen.
Close-up of the controller's LCD screen showing the Main Menu

Figure 6: Controller LCD Screen - Main Menu

4.3. Wi-Fi Setup and App Monitoring

The controller has built-in Wi-Fi for remote monitoring and control via the ESP RainMaker app.

  1. Download App: Download the ESP RainMaker app from the App Store (iOS) or Google Play (Android).
  2. Create Account: Log in or create an account within the app.
  3. Add Device: After power-on, the ESP32 module in the controller will broadcast via Bluetooth Low Energy (BLE) for 30 minutes. In the app, tap 'Add Device' -> 'Choose No QR Code' -> Select 'BLE' as the provisioning method.
  4. Connect: Look for a device starting with 'PROV_' and tap it.
  5. Password: Enter the password 88888888, then follow the prompts to complete the Wi-Fi setup.
  6. Re-enable BLE: If no 'PROV_' device is found (BLE may have timed out), go to 'Menu' > 'Reset Wi-Fi' on the controller to re-enable BLE broadcasting.

Once connected, you can monitor real-time data including PV voltage and current, battery voltage and charging current, charging power and cumulative energy, temperature, and system status.

Screenshots of the ESP RainMaker App interface for iOS and Android, showing various system parameters and graphs

Figure 7: ESP RainMaker App Interface for Monitoring

6. Troubleshooting

Here are common issues and their solutions:

ProblemSolution
No displayCheck battery connection and fuse.
PV LED offCheck solar panel wiring and daylight conditions.
Battery not chargingCheck battery type settings and voltage.
Wi-Fi not connectingReset Wi-Fi on the controller and retry BLE pairing.
Fan is noisy and always on max speed at 10A load, charging stops at max voltage and doesn't resume automatically.This behavior may indicate a specific operational characteristic or a potential issue. Ensure battery type settings are correct. If the issue persists, contact customer support.

7. Specifications

ParameterHX40AHX60AHX80A
MPPT Maximum Charging Current40A60A80A
Adjustable PV Charging Current0-40A0-60A0-80A
PV Max Open-Circuit Input Voltage250V
Battery Voltage12/24/36/48/60/72/84/96/108/120V
Battery TypeTernary lithium, lithium iron phosphate batteries, lead-acid batteries, gel batteries, and User-defined
PV Min Operating Input VoltageMust be over 5V higher than the battery pack voltage
Charging ModeMPPT Automatic Maximum Power Point Tracking
PV Minimum Startup VoltagePV voltage is 5V higher than battery voltage (enables low-current charging even on rainy or cloudy days)
LCD Touch ButtonsLCD Display: Power Generation, PV Voltage, Battery Voltage, Charging Current, Power Generation Operating Status, Daily Power Generation Line Chart, Monthly Power Generation Chart
Output VoltageFollows Battery Pack Voltage
DC Output ConfigurationOff, Auto
Wi-Fi IoT FunctionBuilt-in Wi-Fi + APP Remote Monitoring
Operating Ambient Temperature-25°C - 46°C
Standby Power Consumption3W
Overall Efficiency99%
Temperature Protection90°C
Temperature Rise ProtectionReduces Power Output When Temperature Exceeds 80°C
Protection FunctionsPV Array Protection: Short Circuit, Overvoltage, Overcurrent, Reverse Polarity; Battery Protection: Overcharge, Reverse Polarity, Undervoltage
Humidity0-90%RH (Non-Condensing)
Equipment Protection RatingIP22
Altitude0-3000m
Language typeEnglish and Portuguese

8. User Tips

  • Setup Assistance: If you encounter any difficulties during setup or installation, the seller provides quick and helpful support. Do not hesitate to reach out for assistance.
  • Battery Type Setting: Ensure your battery type is correctly configured in the controller's menu. Incorrect settings can lead to charging issues or unexpected behavior.
  • App Monitoring: Utilize the ESP RainMaker app for comprehensive monitoring of your solar system's performance, including PV voltage, charging power, and battery status.

9. Warranty and Support

To ensure superior quality, all MPPT solar controllers undergo rigorous inspections before leaving the factory. Our company guarantees that the controllers are in good working condition with complete components.

9.1. Warranty Period

A one-year free warranty service is provided from the date of purchase.

9.2. Warranty Terms

Within one year from the date of purchase, if the controller malfunctions or sustains component damage under normal operation, our technical personnel will conduct an inspection. Upon confirmation of eligible faults, we will provide free repair services and replacement of defective parts, with all faulty components retained by our company.

9.3. Warranty Exclusions

The warranty for the controller will be automatically void under the following circumstances:

  1. Alteration of the company's trademark.
  2. Damage caused by improper operation, negligent use, or force majeure events.
  3. Unauthorized disassembly, repair, or modification by personnel other than our company's technical staff; or tampering with/removal of the controller's serial number or warranty seal.
  4. Installation not in accordance with the original manufacturer's installation instructions.

Please keep your purchase receipt (invoice) properly, as it must be presented for inspection by our technical staff when requesting warranty service.

© 2024 HXCONTROLLER. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.