Product Overview
The Dooya DC1650A and DC1651A are RF433MHz wall-mounted remote controls (emitters) designed to operate Dooya tubular motors. The DC1650A is a single-channel switch, while the DC1651A is a double-channel switch, allowing control of multiple motors or groups of motors.
Safety Information
- Always turn off the main power supply to the motor before performing any installation or wiring.
- Ensure any wiring is done by a qualified professional and complies with local electrical codes.
- This product is designed for low voltage applications (below 50Vac or 75Vdc) if wired.
- Do not expose the device to moisture or extreme temperatures.
Installation
The wall switch is designed for surface mounting. Follow these steps for proper installation:
- **Prepare for Installation:** Ensure the area where the switch will be installed is clean and dry.
- **Mount the Backplate:** Secure the switch's backplate to the wall using appropriate screws. Ensure it is level and firmly attached.
- **Attach the Switch:** Carefully attach the main switch unit to the mounted backplate.
- **Activate Battery (if applicable):** If your switch is battery-powered, remove any protective tabs (e.g., "REMOVE BEFORE USE") to activate the battery.
Pairing with Tubular Motor
This section describes how to pair your Dooya wall switch (emitter) with a Dooya tubular motor. The process involves powering the motor and then performing a sequence of button presses on the wall switch.
- **Power On the Motor:** Connect the tubular motor to its power supply. You should hear a beep and the motor will briefly rotate, indicating it's ready for pairing.
- **Initiate Pairing on Switch:** Simultaneously press and hold the "Up" button and the "Stop" button on the wall switch.
- **Confirm Pairing:** Press the "Up" button twice.
- **Finalize Pairing:** Press the "Up" button once more. The motor should respond with a movement, confirming successful pairing.
Note:
- One channel of the wall switch can group control up to 20 Dooya RF433 motors after each motor is paired separately. For example, a DC1650A (single channel) can control 20 motors simultaneously.
- The DC1651A (double channel) has two independent channels, each capable of controlling up to 20 motors.
Basic Operation
The Dooya wall switches feature intuitive buttons for controlling your tubular motor(s).
- **Up Button (^):** Press to move the motor upwards (e.g., open blinds/curtains).
- **Stop Button (-):** Press to stop the motor at its current position.
- **Down Button (v):** Press to move the motor downwards (e.g., close blinds/curtains).
For DC1651A (Double Channel), each set of Up/Stop/Down buttons controls a separate channel.
Maintenance
- **Cleaning:** Wipe the surface of the switch with a soft, dry cloth. Avoid using abrasive cleaners or solvents.
- **Battery Replacement:** If the switch becomes unresponsive or the indicator light dims, replace the internal battery (if applicable) according to the manufacturer's instructions.
- **Environmental Conditions:** Keep the switch in a dry environment and avoid direct exposure to sunlight or extreme temperatures to prolong its lifespan.
Troubleshooting
- **Motor not responding:**
- Ensure the motor is powered on.
- Verify the wall switch battery is functional and activated.
- Re-attempt the pairing process (see "Pairing with Tubular Motor" section).
- **Intermittent control:**
- Check for potential RF interference from other devices.
- Ensure the switch is within the effective range of the motor.
Specifications
| Feature | Specification |
|---|---|
| Product Type | RF433 Emitter Wall Switch |
| Models | DC1650A (Single Channel), DC1651A (Double Channel) |
| Communication Frequency | RF433MHz |
| Control Capacity (per channel) | Up to 20 Dooya RF433 motors |
| Dimensions (approx.) | 86mm x 86mm x 15mm (DC1651A, similar for DC1650A) |
| Wattage | 5V (if wired, otherwise battery-powered) |
| Battery Included | No (may require internal battery for RF function, often pre-installed with pull tab) |
| Origin | Mainland China |
| Package Weight | 0.3 kg |
| Package Dimensions | 9cm x 9cm x 6cm |
User Tips
- **Motor Compatibility:** The DC1650A and DC1651A are compatible with Dooya RF433 motors, such as the Dooya DT82TV/S motor. Ensure your motor is a Dooya RF433 model for proper functionality.
- **Group Control:** A single channel on these wall switches can control up to 20 individual Dooya RF433 motors. This is useful for operating multiple blinds or curtains in a room simultaneously.
- **Battery Activation:** If your switch is new and not responding, check for a plastic pull tab in the battery compartment and remove it to activate the battery.
Environmental Information
This product complies with EU RoHS directives. Do not dispose of this product as household waste. Please recycle it in accordance with local regulations for waste electrical and electronic equipment.
Manufacturer & Support
Manufacturer: Lumi United Technology Co., Ltd.
Manufacturer Address: 8th Floor, JinQi Wisdom Valley, No. 1 Tangling Road, Liuxian Ave, Taoyuan Residential District, Nanshan District, Shenzhen, China
Manufacturer Phone: +86-18589043609
EU Authorized Representative: Sophie Bennett
EU Representative Address: 9 rue du Bat d'Argent, 69001 Lyon, France
EU Representative Phone: +33-774555006