BAOFENG UV-9R EU

Contents

Baofeng UV-9R EU Professional Commercial Walkie Talkie User Manual

Brand: BAOFENG | Model: UV-9R EU

1. Introduction

Thank you for purchasing the Baofeng UV-9R EU Amateur Portable Radio. This device offers high performance and stable wireless two-way radio communication. It is a factory-developed IP57 waterproof two-way radio, especially suitable for maritime and shipping users. Please read this manual carefully before use. The information presented herein will help you to derive maximum performance from your radio.

2. Safety Information

The following safety precautions shall always be observed during operation, service, and repair of this equipment:

  • This equipment shall be serviced by qualified technicians only.
  • Do not modify the radio for any reason.
  • Use only supplied or approved batteries and chargers.
  • Do not use any portable radio that has a damaged antenna. If a damaged antenna comes into contact with your skin, a minor burn can result.
  • Turn off your radio prior to entering any area with explosive and flammable materials.
  • Do not charge your battery in a location with explosive and flammable materials.
  • To avoid electromagnetic interference and/or compatibility conflicts, turn off your radio in any area where posted notices instruct you to do so.
  • Turn off your radio before boarding an aircraft. Any use of a radio must be in accordance with airline regulations or crew instructions.
  • Turn off your radio before entering a blasting area.
  • For vehicles with an air bag, do not place a radio in the area over an air bag or in the air bag deployment area.
  • Do not expose the radio to direct sunlight over a long time, nor place it close to heating source.
  • When transmitting with a portable radio, hold the radio in a vertical position with the microphone 3 to 4 centimeters away from your lips. Keep antenna at least 2.5 centimeters away from your body when transmitting.

WARNING: If you wear a radio on your body, ensure the radio and its antenna are at least 2.5 centimeters away from your body when transmitting.

3. Features and Functions

The Baofeng UV-9R EU is an IP57 dust and waterproof two-way radio, ensuring reliability even in wet environments. It features drop resistance and rolling resistance.

Baofeng UV-9R EU walkie-talkie highlighting features like 10W High Power, Clear LCD Screen, Reliable Two-Way Radio, Dual Band VHF/UHF, Strong Signal, Long Battery Life, Durable Design, Easy Operation, Noise Reduction Clear Sound, High Quality Voice Coil, Noise Reduction Magnet.

Figure 1: Baofeng UV-9R EU with key features.

Key Features:

  • Certification: EU legal CE certified, fully compliant with European radio standards.
  • Durability: IP45 waterproof and dustproof rugged design, drop-resistant and rainproof.
  • Communication: Dual-band handheld transceiver with LCD display.
  • Frequency Range: VHF 130-176MHz & UHF 400-520MHz.
  • Power Output: High power/mid/low (5W/3W/1W) selectable.
  • Channels: Up to 128 memory channels.
  • Noise Reduction: Effectively reduces noise for clearer communication, featuring a high-quality diaphragm, noise reduction magnet, and clear voice coil.
  • Interference Control: CTCSS&DCS anti-interference for private communication.
  • Special Functions: Crossband reception/transmission, Tone end of transmission, VOX (Voice Operated Transmission), DTMF emergency alarm, ANI code, Emergency SOS sound and light alarm.
  • Frequency Step: Selectable steps of 2.5/5/6.25/10/12.5/20/25/50 kHz.
  • Battery Saving: 'SAVE' function.
  • Programmable: By PC.
  • Bandwidth: Broadband (Wide 25KHz) / Narrowband (Narrow 12.5KHz), selectable.
  • FM Radio: Commercial FM radio receiver (65 MHz ~ 108 MHz).
  • Display: Illumination and programmable keyboard, clear and easy to read LCD screen.
  • Built-in LED flashlight.
  • Battery: 2200mAh large capacity battery for long standby and all-day working time.
Baofeng UV-9R EU highlighting new noise reduction technology with diagrams of diaphragm, magnet, and voice coil.

Figure 2: Noise Reduction Feature.

Baofeng UV-9R EU showing dual band capability, physical rotation button for comfortable operation, and multi-function button for easy calls.

Figure 3: Dual Band and Physical Rotation Button.

Baofeng UV-9R EU with a clear and easy-to-read LCD screen displaying frequency information.

Figure 4: Clear LCD Screen.

Baofeng UV-9R EU as a two-way radio, illustrating its ability to stay connected anywhere with clear and stable communication.

Figure 5: Two-Way Radio Communication.

4. Package Contents

Carefully unpack the transceiver. We recommend that you identify the items listed below before discarding the packing material. If any items are missing or have been damaged during shipment, please contact your dealer immediately.

Diagram showing the standard package contents for the Baofeng UV-9R EU: Charger, Battery, Antenna, and Clip/Lanyard.

Figure 6: Standard Package Contents.

Standard Items:

  • Baofeng UV-9R EU Transceiver
  • Battery Pack
  • Antenna
  • Charger (Drop-in Charging Tray and Adapter)
  • Belt Clip
  • Handstrap

Optional Accessories:

Items included in the package may differ depending on the country of purchase. For more information, consult your dealer or vendor. Optional accessories may include:

  • Power Cord
  • Lapel Speaker-Microphone
  • Program Cable
  • Earbud Microphone

5. Setup

5.1. Installation of Accessories

5.1.1. Installing the Antenna

Install the antenna by turning it clockwise onto the connector until it stops. Hold the antenna by its base, not its top, when installing. If using an external antenna, ensure the SWR is about 1.5:1 or less to prevent damage to the transceiver's final transistors. Do not hold the antenna with your hand or wrap the outside of it during operation. Never transmit without an antenna.

5.1.2. Installing the Belt Clip

If necessary, install the belt clip at the rear of the battery compartment cover using the provided screws. Do not use any kind of glue to fix the screw on the belt clip, as solvents may damage the battery casing.

5.1.3. Micro-Headset Installation

Plug the external micro-headset connector into the 'SP.& MIC' jack on the side of the transceiver.

5.2. Battery Installation

When attaching the battery, ensure it is parallel and in good contact with the aluminum chassis. The battery bottom should be about 1 to 2 centimeters below the bottom of the radio's body. Align the battery with the guide rails on the aluminum chassis and slide it upwards until a 'click' is heard, indicating the battery latch has locked it in place.

To remove the battery, first turn off the radio. Slide the battery latch at the bottom of the radio's body in the direction indicated by the arrow. Slide down the battery for about 1 to 2 centimeters, then remove it from the radio's body.

5.3. Battery Charging

Use only the charger specified by the manufacturer. The charger's LED indicates the charging progress.

  1. Plug the power cord into the adapter.
  2. Plug the AC connector of the adapter into the AC outlet socket.
  3. Plug the DC connector of the adapter into the DC socket on the back of the charger.
  4. Place the radio with the battery attached, or the battery alone, in the charger.
  5. Ensure the battery is in good contact with the charging terminals. The charging process initiates when the red LED lights.
  6. The green LED lights about 4 hours later, indicating the battery is fully charged. Then remove the radio with the battery attached or the battery alone from the charger.

Charging Status LED Indication:

Charging StatusLED Indication
Standby (no-load)Red LED flashes, while Green LED glows
ChargingRed LED solidly glows
Fully ChargedGreen LED solidly glows
ErrorRed LED flashes, while Green LED glows

5.4. Battery Information and Tips

5.4.1. Initial Use

New batteries are shipped uncharged from the factory. Charge a new battery for 5 hours before initial use. Maximum battery capacity and performance are achieved after three full charge/discharge cycles. If the battery power runs low, recharge it.

WARNING: To reduce the risk of injury, charge only the battery specified by the manufacturer. Other batteries may burst, causing bodily injury and property damage. Do not dispose of batteries in a fire! Dispose of batteries according to local regulations (e.g., recycling). Do not dispose as household waste. Never attempt to disassemble the battery.

5.4.2. Battery Tips

  • When charging, keep the temperature between 5°C and 40°C. Temperatures outside this range may cause battery leakage or damage.
  • When charging a battery attached to a radio, turn the radio off to ensure a full charge.
  • Do not cut off the power supply or remove the battery while charging.
  • Never charge a wet battery. Dry it with a soft cloth prior to charging.
  • The battery will eventually wear out. When operating time is noticeably shorter, it's time to buy a new battery.

5.4.3. Prolong Battery Life

  • Battery performance decreases significantly below 0°C. A spare battery is recommended in cold weather.
  • Clean battery contacts with a dry cloth to prevent charging issues.

5.4.4. Battery Storage

  • Fully charge a battery before long-term storage to prevent over-discharge damage.
  • Recharge Li-Ion batteries every 6 months during storage to avoid capacity reduction.
  • Store batteries in a cool, dry place at room temperature to reduce self-discharge.

6. Controls and Display

6.1. Radio Overview

Diagram of Baofeng UV-9R EU showing the location of its buttons and features: Keyboard, Display Screen, PTT Button, Indicator Light, Flashlight, Antenna, Charging Port.

Figure 7: Product Button Display.

The Baofeng UV-9R EU features a precision design for easy operation. Key components include:

  • 1. Antenna: For transmitting and receiving signals.
  • 2. LCD: Dual band LCD screen for clear visibility.
  • 3. Keypad: Multi-function buttons for easy operation.
  • 4. Knob (ON/OFF, volume): Controls power and audio level.
  • 5. Flashlight: Built-in LED flashlight for emergencies.
  • 6. Speaker: For audio output.
  • 7. Microphone: For voice input.
  • 8. Battery Latch: Secures the battery.
  • 9. PTT (Push-to-Talk) Button: For instant communication.
  • 10. SK-side key1/F: Multi-function side key.
  • 11. SK-side key2/M: Multi-function side key.
  • 12. Strap Buckle: For attaching a handstrap.
  • 13. Accessory Jack: For external accessories like headsets.
  • 14. LED Indicator: Status indication at a glance.

6.2. Command/Key Definition

  • Power On: Rotate the PWR/VOL Switch clockwise. You will hear a 'Beep' sound and the present channel will be reported. Adjust volume by rotating the PWR/VOL Switch.
  • [SOS] Emergency Alarm: Long press [SOS] to activate the alarm function (green and red lights flash). Press again to release.
  • [PTT] Button: Press and hold to transmit, release to receive.
  • SK-SIDE KEY1/[F]: Press [F] to activate/deactivate the FM Radio.
  • SK-SIDE KEY2/[M]: Press [M] to turn on/off the flashlight. Press and hold [M] to monitor the signal.
  • [MENU] Key: To enter the radio menu and confirm settings. Press and hold [MENU] during power-on to switch between frequency and channel modes.
  • [▲]/[▼] Keys: Press and hold for fast frequency up/down. Press briefly for scanning.

6.3. LCD Display Icons

The display icons appear when certain operations or specific features are activated:

IconDescription
CT'CTCSS' activated
DCS'DCS' activated
+-Frequency Shift + / -
OneFrequency offset direction for accessing repeaters
VOXFunction 'VOX' enabled
RReverse function activated
NWide Band selected
SelfBattery Level indicator
LKeypad lock function activated
YISignal Strength Level
100Operating channel
75Operating frequency

7. Operation

7.1. Radio ON/OFF and Volume Control

Ensure the antenna and battery are correctly installed and charged. Rotate the knob clockwise to turn the radio on. Rotate the knob fully counter-clockwise until a 'click' is heard to turn the radio off. Turn the knob clockwise to increase the volume, or counter-clockwise to decrease the volume. Note: The radio will not sound 'click' if the voice prompt function is turned off (set from Function 38).

7.2. Transmit and Receive

Choose the correct channel number or enter the desired frequency. Press and hold the PTT button to transmit, then speak into the microphone. Release PTT to receive.

  • When PTT is pressed, 'L' on the LCD indicates low power.
  • When PTT is pressed, 'M' on the LCD indicates mid power.
  • When PTT is pressed, 'H' on the LCD indicates high power.
  • Press [PTT] then [SOS] to transmit 1750HZ.
  • Press [PTT] then DTMF Numbers to transmit DTMF.

7.3. VOX (Voice Operated Transmission)

This function activates transmission automatically by detecting your voice, eliminating the need to press PTT. Transmission terminates when you stop speaking. Adjust the VOX Gain level for smooth transmission.

Operation:

  1. Press [MENU] to enter menu setting.
  2. Press [▲] or [▼] to Function 4 (VOX).
  3. Press [MENU], then use [▲] or [▼] to choose a level from 1-10 (10 is most sensitive).
  4. Press [MENU] to confirm. The LCD will show 'VOX'.
  5. To turn off VOX, choose 'OFF' and press [MENU].

7.4. AUTOLK (Keypad Locked Automatically)

The transceiver offers auto lock and manual lock options. 'OFF' disables auto lock. 'ON' locks the keypad if no button is pressed for more than 2 seconds.

Operation:

  1. In standby, press [MENU] + number key 24. The screen will display 'AUTOLK'.
  2. Press [MENU] to enter, then use [up] and [down] to select 'ON' or 'OFF'.
  3. Press [MENU] to confirm, then [EXIT] to return to standby.

7.5. VFO/Channel Mode

Turn off the radio, then press [MENU] and rotate the sound knob to turn on the radio. The screen will show the frequency or 'CH-008' (channel number), indicating the current mode. You can switch between VFO (Frequency) and Channel modes this way.

Selecting a Frequency or Channel:

Press the [▲] or [▼] key to select the desired frequency/channel. Press and hold for fast scrolling.

7.6. TDR (Dual Watch/Dual Reception)

This feature allows operation between frequency A and frequency B. The transceiver periodically checks for signals on the scheduled frequency. If a signal is received, the unit will remain on that frequency until the signal disappears.

Operation:

  1. In standby, press [MENU] + keyboard [7TDR]. The screen will display 'TDR'.
  2. Press [MENU] to enter, then use [UP] or [DOWN] to select 'TDR' OFF or ON.
  3. Press [MENU] to confirm, then [EXIT] to return to standby.

7.7. DEL-CH (Delete Channel)

Operation:

  1. In standby, press [MENU] + [Number key 28]. The screen will display 'DEL-CH'.
  2. Press [MENU] to enter, then use [UP] or [DOWN] to select the channel to delete.
  3. Press [MENU] to confirm, then [EXIT] to return to standby.

The transceiver has 128 memory channels (000 to 127). This operation is invalid if you are in a channel without DH-display, meaning the channel is not parameterized.

7.8. MEM-CH (Stored in Memory Channel)

When the transceiver is in frequency mode or standby, you can input the frequency and other parameters to store them.

Operation:

  1. In standby, press [MENU] + [Number key 27]. The screen will display 'MEM-CH'.
  2. Press [MENU] to enter, then use [UP] or [DOWN] to select the desired channel order.
  3. Press [MENU] to confirm, then [EXIT] to return to standby.

A complete memory channel includes RX frequency, TX frequency, CTCSS, DCS, RF Power, Bandwidth, PTT-ID, BCL, ANI, Scan add to, Channel Name, etc. Except for Scan add to and Channel Name, other settings can be finished by keypad under VFO mode.

Example: Programming data into CH106

ParameterExample Value
RX Frequency440.625MHz
TX Frequency430.625MHz
RX CTCSS100.0Hz
TX DCS250.3Hz
RF PowerHigh
BandwidthWide
PTT-IDOFF
  1. Check if CH106 already contains data (MENU 28). If so, delete it.
  2. Press and hold [MENU] key, then power on to enter VFO mode. Press [EXIT/AB] to select frequency A (UP).
  3. Enter 440.625MHz.
  4. Through the MENU, set other parameters like CTCSS, DCS, RF Power, Bandwidth, etc.
  5. After setting all parameters, press [MENU] key, then go to MENU 27 and press [MENU] two times to store the data into CH106.

7.9. CTCSS/DCS Scanning

Before scanning, ensure you have an RX frequency and Dual Standby is off, and the radio is in VFO mode.

Operation:

  1. Go to MENU 11.
  2. Press [MENU] once, then press [*/SCAN] key.
  3. Simultaneously, press the PTT of another radio. The CTCSS scanning will start automatically.
  4. When scanning stops (meaning the same CTCSS as the other radio is found), press [MENU] to store the CTCSS.

7.10. Repeater Tail Tone

Repeaters receive on one frequency and retransmit on another. The courtesy tone (beep) indicates the repeater is active. MENU 35 and MENU 36 should be OFF for repeater use. Parameter MENU 37 (Repeater Tail Tone Delay) should be set to 5 (range 1-10).

7.11. CTCSS/DCS

CTCSS (Continuous Tone Coded Squelch) and DCS (Digital Coded Squelch) are used to establish communication in closed user groups. The squelch opens only when receiving a frequency with the same CTCSS or DCS code as programmed in your transceiver. If codes differ, the squelch will not open, but the signal may still be heard.

Note: The use of CTCSS or DCS does not guarantee complete confidentiality of communication.

7.12. Sound-Light Alarm / Cancel Alarm

The radio has 3 alarm modes: Alarm, Sending alarm code, and Sending background sound. Pressing [SOS] activates the alarm sound and light flashes. Press [SOS] again to stop. In emergency alarm mode, only [PTT] and SOS keys are workable. Pressing [PTT] to transmit will stop the alarm when the radio receives the transmission.

9. Copying (Radio Cloning)

To copy settings from one radio (Radio A) to another (Radio B), follow these steps:

  1. Connect the two radios with a special data cable.
  2. Turn on Radio B.
  3. Press [MONI] on Radio A, then turn on Radio A. The screen will show 'COPYING'.
  4. Once copying is finished, Radio B will power off and then power on automatically.

Repeat steps 2 and 3 to clone more radios. If cloning is unsuccessful, turn off both radios and ensure the clone cable is connected correctly.

10. Specifications

10.1. General

ParameterValue
Frequency Range65MHz-108MHz (Commercial FM radio reception only), VHF: 136MHz-174MHz (Rx/Tx), UHF: 400MHz-520MHz (Rx/Tx)
Memory ChannelsUp to 128 channels (JSON indicates 999 Storage Channel, manual states 128)
Frequency Stability2.5 ppm
Frequency Step2.5kHz/5kHz/6.25kHz/10kHz/12.5kHz/20kHz/25kHz
Antenna Impedance50Ω
Operating Temperature-20°C to +60°C
Supply VoltageRechargeable Lithium-Ion mAh 7.4V/1800 (Battery Capacity: 1800mAh)
Consumption in Reception380mA
Consumption in Transmission≤1.4 A
Mode of OperationSimplex or semi-duplex
Duty Cycle03/03/54 min. (Rx / Tx / Standby)
Dimensions65mm x 41.5mm x 133.8mm (JSON indicates 173*100*95 mm, likely package dimensions)
Weight279g (approximate)
MaterialPlastic
Waterproof / Water-ResistantIP45

10.2. Transmitter

ParameterValue
RF Power5W/1W (JSON indicates 5w-10w)
Type of ModulationFM
Emission Class16KΦF3E/11KΦE3E (W/N)
Maximum Deviation≤ ±5 kHz/≤±2.5 kHz (W/N)
Spurious Emissions<-60 dB

10.3. Receiver

ParameterValue
Receiver Sensitivity0.2 µV (at 12 dB SINAD)
Intermodulation60 dB
Audio Output1W
Spurious Radiation≥65dB

Note: All specifications shown are subject to change without notice.

11. Troubleshooting

ProblemPossible Cause / Solution
The radio does not start.The battery is low; replace with a charged battery or proceed to charge. The battery is not installed correctly; remove and reattach it.
The battery runs down quickly.The battery life has come to an end; replace with a new one. Ensure the battery is fully charged and made in full.
The receiving indicator LED lights but no sound from the speaker.The volume setting is too low. Ensure CTCSS or DCS undertones are the same as those programmed in the transceiver of other group members.
In 'standby' mode, the transceiver transmits without pressing the 'PTT'.Check if the 'VOX' level adjustment function is set too sensitive.
Receiving communications from other user groups while communicating with your group.Change frequency or channel. Change the undertones 'CTCSS' or code 'DCS' in your group.
Communication with other members of your group is poor or low quality.You or your partner is too far away or in an area of poor radio signal propagation (e.g., inside a tunnel, underground car park, mountainous area, large metal structures).
When transmitting, other group members do not receive the communication.Ensure CTCSS or DCS undertones are the same as those programmed in the transceiver of other group members. You or your partner are too far or in a bad RF signal propagation area.

If these checks do not resolve the issue, contact your distributor, dealer, or service center.

12. User Tips

No specific user tips were available from provided reviews or Q&A content.

13. Warranty and Support

13.1. Warranty Certificate

The device is guaranteed for a period of TWO YEARS from the date of sale to the final user. This Warranty Certificate is unique, non-transferable, and cannot be reissued. Substitution of product failure or any part thereof does not extend the guarantee period.

The warranty covers the replacement and free replacement of all parts defective in materials and components used in manufacturing and/or assembly.

The warranty does not cover faults caused by:

  • Accident, improper installation and use.
  • Electric shock (e.g., storms).
  • Connection to a power source other than specified.
  • Reverse polarity in the diet.
  • Claims due to deterioration in the external appearance from normal use.
  • The amount or condition of accessories.

Checking the accessories is the responsibility of the purchaser at the time of purchase. The warranty does not cover rechargeable batteries, even if part of the equipment, as they are considered consumables. Impairment must be reported within fifteen days of purchase.

13.2. Voiding the Warranty

The warranty is void under the following assumptions:

  1. Devices that have been manipulated by unauthorized service providers or anyone other than authorized personnel.
  2. Equipment and accessories where the serial number has been altered, deleted, or filed unreadable.
  3. Use of the product other than as intended.

To claim warranty, provide the defective device with accessories and the following documentation:

  1. Warranty Certificate, duly completed and sealed.
  2. Original invoice clearly identifying the device and date of purchase.
  3. Description of the faults.

The warranty terms do not exclude, modify, or restrict the statutory rights of the buyer by virtue of the laws in force at the time of purchase, but are added to them.

14. Documents and Media

A comprehensive user manual in PDF format is available for download and detailed reference:

Download User Manual (PDF)

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.