MAT-TUNER mAT-1F

Contents

mAT-1F QRP Automatic Antenna Tuner Instruction Manual

Dedicated for Yaesu FTX-1 Field Transceivers

1. Introduction

The mAT-1F is a compact and efficient automatic antenna tuner specifically designed for use with the Yaesu FTX-1 Field transceiver. It provides seamless integration and operation, allowing users to tune their antennas directly from the transceiver's front panel, similar to using an original Yaesu tuner. This tuner offers flexibility with both coaxial and wire antenna connections, making it suitable for various QRP (low power) operations.

2. Safety Information

Important Warning: Do NOT connect an antenna to both the WIRE and COAX terminals at the same time. This can cause damage to the tuner or transceiver.

This device is intended for amateur radio use by qualified individuals. Ensure all connections are secure and correct before operating. Do not expose the tuner to moisture or extreme temperatures. Disconnect power before making or changing any connections.

3. Package Contents

Please check the package for the following items:

  • 1 x mAT-1F Automatic Antenna Tuner
  • 1 x mAT-CBB1M Coaxial Jumper Cable (1 meter)
  • 1 x mAT-CF Control Cable (1 meter)
mAT-1F Tuner with included coaxial and control cables
Figure 3.1: mAT-1F Tuner with included coaxial and control cables.

4. Product Overview

The mAT-1F tuner features a robust design with clearly labeled connectors for easy setup and operation.

4.1. Top Panel Connectors

  • WIRE: Banana terminal for connecting a long wire antenna.
  • COAX: BNC connector for connecting a coaxial-fed antenna.
  • GND: Ground terminal.

4.2. Bottom Panel Connectors

  • RF IN: BNC jack for RF input from the transceiver's HF antenna port.
  • ON/TUN RADIO: Control cable jack for connecting to the transceiver's "TUNER" port.
Close-up of the top panel connectors: WIRE (banana plug), COAX (BNC connector), and GND (ground terminal).
Figure 4.1: Top panel connectors (WIRE, COAX, GND).
Angled view of the mAT-1F Tuner, showing the bottom panel connectors.
Figure 4.2: Bottom panel connectors (RF IN, ON/TUN RADIO).

5. Setup

5.1. Connecting the Antenna Tuner

  1. Connect the mAT-CBB1M coaxial jumper cable from the transceiver's HF antenna port to the RF IN BNC jack on the bottom panel of the mAT-1F tuner.
  2. Connect the mAT-CF control cable from the transceiver's "TUNER" port to the ON/TUN RADIO jack on the bottom panel of the mAT-1F tuner.
  3. Connect your antenna to the top panel of the mAT-1F tuner. Choose one of the following options:
    • For a coaxial-fed antenna, connect it to the COAX BNC jack.
    • For a long wire antenna, connect it to the WIRE banana terminal.

    Remember: Do NOT connect both a coaxial and a wire antenna simultaneously.

  4. (Optional) Connect a ground wire from the GND terminal on the top panel to a suitable ground point.
Connection diagram: Examples for connecting an antenna feeder (coax) and a longline antenna (wire).
Figure 5.1: Connection examples for coaxial and longline antennas.

6. Operating Instructions

The mAT-1F tuner is designed for seamless operation with your Yaesu FTX-1 Field transceiver. Once connected, it functions identically to the original Yaesu antenna tuner.

6.1. Automatic Tuning

  1. Turn on your Yaesu FTX-1 Field transceiver.
  2. Select the desired operating frequency and mode.
  3. Initiate the tuning process directly from your transceiver's front panel, as you would with the original tuner. Refer to your Yaesu FTX-1 Field manual for specific instructions on initiating the tuning cycle.
  4. The mAT-1F will automatically tune the antenna for the best SWR (Standing Wave Ratio) within approximately 10 seconds.
  5. Once tuning is complete, the tuner will store the settings for that frequency, allowing for faster recall if you return to the same frequency later.

7. Maintenance

  • Keep the tuner clean and free from dust. Use a soft, dry cloth for cleaning.
  • Ensure all cable connections are tight and free from corrosion.
  • Store the tuner in a dry environment when not in use.
  • Do not attempt to open the casing or repair the unit yourself, as this will void the warranty.

8. Troubleshooting

ProblemPossible CauseSolution
Tuner does not respondControl cable not connected or faulty.Check control cable connection. Ensure it's securely plugged into both the tuner and transceiver.
High SWR after tuningAntenna mismatch too severe; antenna fault; incorrect connection.Check antenna connections. Ensure only one antenna type (coax or wire) is connected. Inspect antenna for damage. Try tuning on a different frequency.
Tuner cycles continuouslyAntenna cannot be tuned to an acceptable SWR.This indicates the antenna system is outside the tuner's matching range. Adjust antenna length or type.

9. Specifications

FeatureDetail
ModelmAT-1F
Frequency Range1.8 - 54 MHz
RF Power Handling10W (Maximum)
Tuning Time< 10 seconds (full tune)
Antenna ConnectorsBNC (Coax), Banana Plug (Wire)
Working Temperature-10℃ to 60℃
Product Size142 x 67 x 28 mm
Net Weight200g
Built-in BatteryNo
OriginMainland China
Dimensions of the mAT-1F Tuner (148mm height, 67mm width).
Figure 9.1: Product dimensions.

10. User Tips

No specific user tips are available from community feedback at this time. Always ensure your antenna system is as efficient as possible before relying on the tuner.

11. Warranty and Support

For warranty information, technical support, or service inquiries, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.

A detailed user manual in PDF format is available for download: mAT-1F User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.