BAOFENG UV-9R EU

Contents

Baofeng UV-9R EU Walkie Talkie User Manual

Model: UV-9R EU

Brand: BAOFENG

Introduction

Thank you for purchasing the Amateur Portable Radio. We always offer high performance, stable wireless two-way radio. Factory developed IP57 waterproof two-way radio, especially for maritime and shipping users. Please read this manual carefully before use. The information presented herein will help you to derive maximum performance from your radio.

Safety Information

The following safety precautions shall always be observed during operation, service and repair of this equipment.

  • This equipment shall be serviced by qualified technicians only.
  • Do not modify the radio for any reason.
  • Use only supplied or approved batteries and chargers.
  • Do not use any portable radio that has a damaged antenna. If a damaged antenna comes into contact with your skin, a minor burn can result.
  • Turn off your radio prior to entering any area with explosive and flammable materials.
  • Do not charge your battery in a location with explosive and flammable materials.
  • To avoid electromagnetic interference and/or compatibility conflicts, turn off your radio in any area where posted notices instruct you to do so.
  • Turn off your radio before boarding an aircraft. Any use of a radio must be in accordance with airline regulations or crew instructions.
  • Turn off your radio before entering a blasting area.
  • For vehicles with an air bag, do not place a radio in the area over an air bag or in the air bag deployment area.
  • Do not expose the radio to direct sunlight over a long time, nor place it close to heating source.
  • When transmitting with a portable radio, hold the radio in a vertical position with the microphone 3 to 4 centimeters away from your lips. Keep antenna at least 2.5 centimeters away from your body when transmitting.

! WARNING: If you wear a radio on your body, ensure the radio and its antenna are at least 2.5 centimeters away from your body when transmitting.

Unpacking and Checking Equipment

Carefully unpack the transceiver. We recommend that you identify the items listed in the following before discarding the packing material. If any items are missing or have been damaged during shipment, please contact your dealers immediately.

Baofeng UV-9R EU radio with included accessories: battery, back clip, lanyard, charger, and antenna.

Image: Baofeng UV-9R EU radio with included accessories: battery, back clip, lanyard, charger, and antenna.

Standard Accessories:

  • Battery Pack
  • Antenna
  • Adapter
  • Drop-in Charging Tray
  • Belt Clip
  • Handstrap

Note: Items included in the package may differ from those listed above depending on the country of purchase. For more information, consult your dealer or vendor.

Installation of Accessories

1. Installing the Antenna

Install the antenna as shown in the figure below and turn it clockwise until it stops.

Diagram showing how to install the antenna on the Baofeng UV-9R EU radio.

Image: Diagram showing how to install the antenna on the Baofeng UV-9R EU radio.

Note:

  • When installing the antenna, don't rotate it by its top, holding it by its base and turn.
  • If you use an external antenna, make sure the 'SWR' is about 1.5:1 or less, to avoid damage to the transceiver's final transistors.
  • Do not hold the antenna with your hand or wrap the outside of it to avoid bad operation of the transceiver.
  • Never transmit without an antenna.

2. Installing the Belt Clip

If necessary, install the belt clip at the rear of the battery compartment cover as shown in the figure below.

Diagram showing how to attach the belt clip to the back of the Baofeng UV-9R EU radio.

Image: Diagram showing how to attach the belt clip to the back of the Baofeng UV-9R EU radio.

Note:

  • Do not use any kind of glue to fix the screw on the belt clip.
  • The solvents in glue may damage the battery casing.

3. Micro-Headset Installation of External

Plug the external micro-headset connector into the jack of 'SP. & MIC' of the transceiver as shown in the figure below.

Diagram showing the location of the SP. & MIC jack for external micro-headset connection on the Baofeng UV-9R EU radio.

Image: Diagram showing the location of the SP. & MIC jack for external micro-headset connection on the Baofeng UV-9R EU radio.

4. Battery Installation

When attaching the battery, make sure the battery is in parallel and in good contact with the aluminum chassis. The battery bottom is about 1 to 2 centimeters below the bottom of the radio's body.

Align the battery with the guide rails on the aluminum chassis and slide it upwards until a 'click' is heard.

The battery latch at the bottom locks the battery.

Turn off the radio before removing the battery.

Slide the battery latch, at the bottom of the radio's body, in the direction indicated by the arrow.

Slide down the battery for about 1 to 2 centimeters, and then remove the battery from the radio's body.

Diagram illustrating the steps for installing and removing the battery pack from the Baofeng UV-9R EU radio.

Image: Diagram illustrating the steps for installing and removing the battery pack from the Baofeng UV-9R EU radio.

Battery Information and Charging

Battery Charging

Use only the charger specified by the manufacturer. The charger's LED indicates the charging progress.

CHARGING STATUSLED INDICATION
Standby (no-load)Red LED flashes, while Green LED glows
ChargingRed LED solidly glows
Fully ChargedGreen LED solidly glows
ErrorRed LED flashes, while Green LED glows
Diagram showing the charging setup for the Baofeng UV-9R EU radio, including the adapter and charging tray.

Image: Diagram showing the charging setup for the Baofeng UV-9R EU radio, including the adapter and charging tray.

Please follow these steps:

  1. Plug the power cord into the adapter.
  2. Plug the AC connector of the adapter into the AC outlet socket.
  3. Plug the DC connector of the adapter into the DC socket on the back of the charger.

1. Initial Use

New batteries are shipped uncharged fully from the factory. Charge a new battery for 5 hours before initial use. The maximum battery capacity and performance is achieved after three full charge/discharge cycles. If you notice the battery power runs low, please recharge the battery.

! WARNING: To reduce the risk of injury, charge only the battery specified by the manufacturer. Other batteries may burst, causing bodily injury and property damage.

  • To avoid risk of personal injury, do not dispose of batteries in a fire!
  • Dispose of batteries according to local regulations (e.g. recycling). Do not dispose as household waste.
  • Never attempt to disassemble the battery.

2. Battery Tips

  1. When charging your battery, keep it at a temperature among 5°C - 40°C. Temperature out of the limit may cause battery leakage or damage.
  2. When charging a battery attached to a radio, turn the radio off to ensure a full charge.
  3. Do not cut off the power supply or remove the battery when charging a battery.
  4. Never charge a battery that is wet. Please dry it with a soft cloth prior to charge.
  5. The battery will eventually wear out. When the operating time (talk-time and standby time) is noticeably shorter than normal performance, it is time to buy a new battery.

3. Prolong Battery Life

  1. Battery performance will be greatly decreased at a temperature below 0°C. A spare battery is necessary in cold weather. The cold battery unable to work in this situation may work under room temperature, so keep it for later use.
  2. The dust on the battery contact may cause the battery cannot work or charge. Please use a clean dry cloth to wipe it before attaching the battery to the radio.

4. Battery Storage

  1. Fully charge a battery before you store it for a long time, to avoid battery damage due to over-discharge.
  2. Recharge a battery after several months' storage (Li-Ion batteries: 6 months), to avoid battery capacity reduction due to over-discharge.
  3. Store your battery in a cool and dry place under room temperature, to reduce self-discharge.

Parts, Controls, and Keys

1. Radio Overview

Product Button Display: Diagram illustrating the various parts and controls of the UV-9R EU radio, including keyboard, display screen, PTT button, indicator light, flashlight, antenna, and charging port.

Image: Product Button Display: Diagram illustrating the various parts and controls of the UV-9R EU radio, including keyboard, display screen, PTT button, indicator light, flashlight, antenna, and charging port.

  1. Antenna
  2. LCD
  3. Keypad
  4. Knob (ON/OFF, volume)
  5. Flashlight
  6. Speaker
  7. Microphone
  8. PTT
  9. SK-side key1/F
  10. SK-side key2/M
  11. Strap buckle
  12. Accessory jack
  13. LED indicator

2. Command/Key Definition

Power On: Rotate PWR/VOL Switch clockwise, you will hear a sound "Beep", report the present channel, the transceiver is ready for working, meanwhile rotate PWR/VOL Switch to adjust the volume.

[SOS] Emergency Alarm: Long press [SOS] to open the alarm function, at this moment, the green light, red light, hand lamp flashes shin at the same time. Press this button again to release the alarm.

[PTT]: Press and hold PTT button, then talk to the microphone. Release PTT to receive.

SK-SIDE KEY1/[F]: Press the [F] button, to activate the FM Radio on; Press it again to deactivate the FM Radio.

SK-SIDE KEY2/[M]: Press the [M] button, to turn on the flashlight; Press it again to turn off. Press and hold on the [M] button, to monitor the signal.

FUNCTION KEYPAD:

[MENU] key: To enter the menu of the radio and confirm the setting. Press and hold [MENU] button, then power on, to switch the frequency mode and channel mode.

[▲] [▼] key: Press and hold [▲] or [▼] key for frequency up or down fast. Press [▲] or [▼] key, the scanning will be opposite.

[EXIT/AB] key: To cancel /clear or exit. While standby, press [EXIT/AB] key to switch between Channel A and Channel B. Under FM radio mode, press [EXIT/AB] key to switch the FM radio band 65-75MHz/76-108MHz.

NUMERIC KEYPAD: Used to enter information for programming the radio's lists and the non-standard CTCSS. Under transmission mode, press the numeric key to send the signal code (the code should be set by PC software).

LCD Display

The display icons appear when certain operations or specific features are activated.

LCD Screen: Clear and easy-to-read display for quick information view on the UV-9R EU transceiver.

Image: LCD Screen: Clear and easy-to-read display for quick information view on the UV-9R EU transceiver.

IconDescription
+Frequency Shift +
-Frequency Shift -
+-Frequency offset direction for accessing repeaters.
SDual Watch/Dual Reception functions activated.
VOXFunction 'VOX' enabled.
RReverse function activated.
NWide Band selected.
Battery Level indicator
LKeypad lock function activated.
Low transmit power.
Operation frequency.
YullSignal Strength Level.
Operating channel.
Operating frequency.
CT'CTCSS' activated.
DCS'DCS' activated.

Basic Operation

1. Radio On-Off/Volume Control

Make sure the antenna and battery are installed correctly and the battery charged. Rotate the knob clockwise to turn the radio on, and rotate the knob fully counter-clockwise until a 'click' is heard to turn the radio off. Turn the knob clockwise to increase the volume, or counter-clockwise to decrease the volume.

Caution: The radio will not sound 'click' if you turn off the voice prompt function. The boot mode display can be set from Function 38.

2. Transmit and Receive

Choose the correct channel No. or enter the frequency which you need. Then press and hold PTT button, the radio is transmitting now, then talk to the microphone, your sound will be transmitted. Release PTT to receive.

  • When you press PTT, the LCD shows L, it means the radio is in low power.
  • When you press PTT, the LCD shows M, it means the radio is in Mid power.
  • When you press PTT, the LCD shows H, it means the radio is in High power.
  • Press [PTT] and then press [SOS] to transmit 1750HZ.
  • Press [PTT] then press DTMF Numbers to transmit DTMF.

3. Function "VOX" (Voice Operated Transmission)

This function is not necessary to push the [PTT] on the transceiver for a transmission. Transmission is activated automatically by detecting the radio voice. When finish speaking, the transmission automatically terminated and the transceiver will automatically receive signal. Be sure to adjust the VOX Gain level to an appropriate sensitivity to allow smooth transmission.

Operate:

  1. Press [MENU] to menu setting.
  2. Press [▲] or [▼] to Function 4, the screen shows 'VOX OFF'.
  3. Press [MENU], sound "VOX" then press [▲] or [▼] to choose the level 1-10, 10 is the most sensitive level.
  4. Press [MENU] to confirm the setting. The LCD screen shows VOX after this function was setting.
  5. You can choose the VOX level to OFF, and press [MENU] then you will off this function.

4. AUTOLK (Keypad Locked Automatically)

The transceiver has two options: auto lock and manual lock. OFF: Turn off auto lock. ON: When you set autolock the keyboard press for more than 2 seconds.

Operate: In standby, press [menu] + number key 24, then the screen will display "AUTOLK". Press [MENU] enter, then press [up] and [down] to select keyboard lock ON or OFF. Press [MENU] to confirm, then press [EXIT] to return to standby.

5. VFO/Channel Mode

Turn off the radio, then press [MENU] and rotate the sound knob to turn on the radio, the screen shows frequency. The lower right corner of the LCD displays the channel number, which means it's in the channel mode. In this way, you can also change the channel mode to VFO.

Selecting a Frequency or Channel

Press the key [▲] or [▼] to select the desired frequency/channel you want. The display shows the frequency / channel selected. Press and hold down the key [▲] or [▼] for frequency up or down fast.

6. TDR (Dual Watch/Dual Reception)

This feature allows you to operate between frequency A and frequency B. Periodically, the transceiver checks whether a signal is received on another frequency that we have scheduled. If you receive a signal, the unit will remain in the frequency until the received signal disappears.

In standby, press [MENU] + keyboard [7TDR] and then screen will display 'TDR'. Press [MENU] enter, then press [UP] or [DOWN] to select 'TDR' OFF or ON. Press [MENU] to confirm, then press [EXIT] to return to standby.

7. DEL-CH (Delete Channel)

In standby, press [MENU] + [Number key 28] and then screen will display 'DEL-CH'. Press [MENU] enter, press [UP] or [DOWN] to select the channel you want to delete. Press [MENU] to confirm, then press [EXIT] to return to standby.

The transceiver has 128 memory channels from 000 to 127. Operate invalid when you into channel without DH- display, it means this channel not parameter.

8. MEM-CH (Stored In Memory Channel)

When transceiver works in frequency mode or in standby, input the frequency and any kind of parameter you want to store.

In standby, press [MENU] + [Number key 27] and then screen will display 'MEM-CH', then press [MENU] enter, press [UP] or [DOWN] to select the desired channel order. Press [MENU] to confirm then press [EXIT] to return to standby.

A complete memory channel includes RX frequency, TX frequency, CTCSS, DCS, RF Power, Bandwidth, PTT-ID, BCL, ANI, Scan add to, Channel Name, etc. Except for the setting of Scan add to and Channel Name, other settings could be finished by keypad under VFO mode.

Example: We want programming all the data into CH106, please do as following:

RX Frequency440.625MHz
TX Frequency430.625MHz
RX CTCSS100.0Hz
TX DCS250.3Hz
RF PowerHigh
BandwidthWide
PTT-IDOFF
  1. We have to check whether there are any data in CH106 or not. Come to MENU 28, if there is a 'CH' before '106', that means there are data. So please delete it and you will find there is not a 'CH' before '106', or else you can't have new data in this channel.
  2. Press and hold [MENU] key, then power on, come to VFO mode. Press [EXIT/AB] key to select frequency A (UP).
  3. Enter 440.625MHz.
  4. Now through the MENU, you can set other parameters. CTCSS,DCS, RF Power, Bandwidth, etc.
  5. After you finish all the other settings, press [MENU] key, then come to MENU 27, press [MENU] key two times, you will know all the data have been stored into CH106, however now only RX frequency was stored. At the same time, you press [MENU] key another two times.

Note: If you want the TX frequency 430.625 stored into CH106, you should do the same steps after you store the RX frequency into CH106.

9. CTCSS/DCS Scanning

Before setting the CTCSS/DCS scanning, you should have a RX frequency and cancel the Dual Standby function, ensure the radio is working under VFO mode.

Come to MENU 11, press [MENU] one time, then press [*/SCAN] key, at the same time, you should press the PTT of another radio, then you will see the CTCSS scanning automatically. When the scanning stops, that means you find the same CTCSS as that of another radio, now press [MENU] to store the CTCSS.

10. Repeater Tail Tone

We all know that repeaters receive on one frequency and simultaneously retransmit that same information on a different frequency. We hear the courtesy tone almost every time we use the repeater. It's that innocuous beep that lets us know that the repeater is alive and, most importantly, that it has heard us. The MENU 35, 36,37 are very helpful settings while your radio work through repeater. MENU 35 and MENU 36 better be set OFF. The parameter of MENU 37 is from 1-10, better set 5.

Sound-Light Alarm/ Cancel the alarm. There are 3 alarm modes in this radio, Alarm, Sending alarm code, sending the background sound. Press [SOS] alarm function, the radio will sound the alarm sound, the light flights also. Press [SOS] again to stop the alarm.

When the radio is in emergency alarm, there are only [PTT] and SOS key workable. Press [PTT] to transmit, when the radio receive the transmit the alarm will stop also.

11. CTCSS/DCS

In some cases only want to establish communications in a closed user group at a particular frequency or channel, for it will use "CTCSS" or code "DCS" for reception.

The "squelch" opens only when receiving a frequency with "CTCSS" or codes "DCS" same as the programmed in your transceiver. If codes of the received signal differs from those programmed in your transceiver, the "squelch" will not open and the received signal can be heard.

Note: The use of "CTCSS" or "DCS" in a communication, does not guarantee complete confidentiality communication.

Shortcut Menu Operation

1. Press the key MENU, then press the key [▲] or [▼] to select the desired menu.

2. Press the key MENU again, come to the parameter setting.

3. Press the key [▲] or [▼] to select the desired parameter.

4. Press the key MENU to confirm and save, press the key EXIT to cancel setting or clear the input.

Diagram illustrating the flow for shortcut menu operation on the Baofeng UV-9R EU radio.

Image: Diagram illustrating the flow for shortcut menu operation on the Baofeng UV-9R EU radio.

Note: Under channel mode, the following menu settings are invalid: CTCSS,DCS,W/N,PTT-ID,BCL, SCAN ADD TO,S-CODE,CHANNEL NAME. Only the H/L power could be changed by pressing #110.

Set Menu Description

MenuFunction/DescriptionAvailable settings
0SQL (Squelch level)0-9
1STEP (Frequency step)2.5/5/6.25/10/12.5/20/25/50kHz
2TXP (Transmit power)HIGH/MID/LOW
3SAVE (Battery save, 1:1/1:2/1:3/1:4)OFF/1/2/3/4
4VOX (Voice operated transmission)OFF/1-10
5W/N (Wideband/narrowband)WIDE/NARR
6ABR (Display illumination)OFF/1/2/3/4/5s
7TDR (Dual watch/dual reception)OFF/ON
8BEEP (Keypad beep)OFF/ON
9TOT (Transmission timer)15/30/45/60.../585/600seconds
10R-DCS (Reception digital coded squelch)OFF/D023N...D7541
11R-CTS (Reception Continuous Tone Coded Squelch)67.0Hz...254.1Hz
12T-DCS (Transmission digital coded squelch)OFF/D023N...D7541
13T-CTS (Transmission Continuous Tone Coded Squelch)67.0Hz...254.1Hz
14VOICE (Voice prompt)OFF/ON
15ANI (Automatic number identification of the radio, only can be set by PC software.
16DTMFST (The DTMF tone of transmitting code.)OFF/DT-ST/ANI-ST/DT+ANI
17S-CODE (Signal code, only could be set by PC software.)1,..., 15 groups
18SC-REV (Scan resume method)TO/CO/SE
19PTT-ID (press or release the PTT button to transmit the signal code)OFF/BOT/EOT/BOTH
20PTT-LT (delay the signal code sending)0,...,30ms
21MDF-A (under channel mode, A channel displays. Note: name display only can be set by PC software.)FREQ/CH/NAME
22MDF-B (under channel mode, B channel displays. Note: name display only can be set by PC software.)FREQ/CH/NAME
23BCL (busy channel lockout)OFF/ON
24AUTOLK (keypad locked automatically)OFF/ON
25SFT-D (direction of frequency shift)OFF/+/-
26OFFSET (frequency shift)00.000...69.990
27MEMCH (stored in memory channels)000,...127
28DELCH (delete the memory channels)000,...127
29WT-LED (illumination display color of standby)OFF/BLUE/ORANGE/PURPLE
30RX-LED (illumination display color of reception)OFF/BLUE/ORANGE/PURPLE
31TX-LED (illumination display color of transmitting)OFF/BLUE/ORANGE/PURPLE
32AL-MOD (alarm mode)SITE/TONE/CODE
33BAND (band selection)VHF/UHF
34TX-AB (transmitting selection while in dual watch/reception)OFF/A/B
35STE (Tail Tone Elimination)OFF/ON
36RP_STE (Tail tone elimination in communication through repeater)OFF/1,2,3...10
37RPT_RL (Delay the tail tone of repeater)OFF/1,2,3...10
38PONMGS (Boot display)FULL/MGS
39ROGER (tone end of transmission)ON/OFF
40A/B-BP (Tone end of reception)OFF/A/B
41RESET (Restore to default setting)VFO/ALL

CTCSS Table

NOTone (Hz)NOTone (Hz)NOTone (Hz)NOTone (Hz)NOTone (Hz)
167.01194.821131.831171.341203.5
269.31297.422136.532173.842206.5
371.913100.023141.333177.343210.7
474.414103.524146.234179.944218.1
577.015107.225151.435183.545225.7
679.716110.926156.736186.246229.1
782.517114.827159.837189.947233.6
885.418118.828162.238192.848241.8
988.519123.029165.539196.649250.3
1091.520127.330167.940199.550254.1

DCS Table

NOCodeNOCodeNOCodeNOCodeNOCode
1D023N22D131N43D251N64D371N85D532N
2D025N23D132N44D252N65D411N86D546N
3D026N24D134N45D255N66D412N87D565N
4D031N25D143N46D261N67D413N88D606N
5D032N26D145N47D263N68D423N89D612N
6D036N27D152N48D265N69D431N90D624N
7D043N28D155N49D266N70D432N91D627N
8D047N29D156N50D271N71D445N92D631N
9D051N30D162N51D274N72D446N93D632N
10D053N31D165N52D306N73D452N94D645N
11D054N32D172N53D311N74D454N95D654N
12D065N33D174N54D315N75D455N96D662N
13D071N34D205N55D325N76D462N97D664N
14D072N35D212N56D331N77D464N98D703N
15D073N36D223N57D332N78D465N99D712N
16D074N37D226N58D343N79D466N100D723N
17D114N38D243N59D346N80D503N101D731N
18D115N39D244N60D351N81D506N102D732N
19D116N40D245N61D356N82D516N103D734N
20D122N41D246N62D364N83D523N104D743N
21D125N42D251N63D365N84D526N105D754N

Copying (Cloning)

The following steps describe how to copy Radio A to Radio B.

  1. Connecting the two radios with special data cable.
  2. Turn on the radio B.
  3. Press [MONI] at the meantime, turn on the radio A, the screen showing 'COPYING'. When the copy finished, Radio B will power off auto and power on auto.

Repeat the above 2 and 3 steps to clone more radios. If you cannot clone successfully, please turn off both A and B radio, and make sure they were connected correctly with clone cable.

Technical Specifications

1. General

Frequency range:65MHz-108MHz (Only commercial FM radio reception). VHF: 136MHz-174MHz (Rx/Tx). UHF: 400MHz-520MHz (Rx/Tx).
Memory channels:Up to 128 channels
Frequency stability:2.5ppm.
Frequency step:2.5kHz/5kHz/6.25kHz/10kHz/12.5kHz/20/kHz/25kHz.
Antenna impedance:50 Ω.
Operating temperature:-20°C to +60°C.
Supply voltage:Rechargeable Lithium-Ion mAh 7.4V/1800.
Consumption in reception:380mA
Consumption in transmission:<1.4 A.
Mode of operation:Simplex or semi-duplex.
Duty cycle:03/03/54 min. (Rx / Tx / Standby).
Dimensions:65mm x 41.5mm x 133.8mm
Weight:279g (approximate).

2. Transmitter

RF power:5W/1W.
Type of modulation:FM.
Emission class:16KF3E/11KF3E (W/N).
Maximum deviation:≤±5 kHz/≤±2.5 kHz (W/N).
Spurious emissions:<-60 dB.

3. Receiver

Receiver sensitivity:0.2 μ V (at 12 dB SINAD).
Intermodulation:60 dB.
Audio output:1W
Spurious Radiation:≥65dB

Note: All specifications shown are subject to change without notice.

Troubleshooting

ProblemPossible cause / solution
The radio does not start.The battery is low, replace the battery with a charged battery or proceed to the battery. The battery is not installed correctly, remove the battery and reattach it.
The battery runs down quickly.The battery life has come to an end, replace the battery with a new one. The battery is fully charged, make sure the battery is made in full.
The receiving indicator LED lights but do not hear the speaker.Make sure the volume setting is too low. Make sure the undertones "CTCSS" or code "DCS" are the same as those programmed in the transceiver of the other members of your group.
When transmitting, the other members of his group do not receive the communication.Make sure the undertones "CTCSS" or code "DCS" programmed in your transceiver are the same as those programmed in the transceiver of the other members of your group. Your partner or you, are too far. You or your partner are in a bad area of RF signal propagation.
In "standby" mode, the transceiver transmits without pressing the "PTT".Check the level adjustment function "VOX" is not set too sensitive.
Receive communications from other user groups while communicating with your group.Change frequency or channel. Change the undertones "CTCSS" or code "DCS" in your group.
Communication with other members of your group is poor or low quality.You or your partner is too far away or in an area of poor radio signal propagation, such as inside a tunnel, inside an underground car park, in a mountainous area, including large metal structures, etc.

Once these checks, if you still have problems with the transceiver, check with your distributor, dealer or service center.

Warranty and Support

Warranty Certificate

Brand:Model no.:Serial no.:
Name of purchaser:
Address:
City:Zip code:
Province/State:Tel no.:Seal and name of the dealer:
Date of purchase:

WARNING: Warranty is valid provided it is complete and properly filled in legibly and clearly present the seal and name of the dealer and have attached the bill proof of purchase of equipment.

Warranty Information

The device described in this Certificate is guaranteed for a period of TWO YEARS from the date of sale to the final user. This Warranty Certificate is unique and not transferable and may not be reissued for new or original or copy. Substitution of product failure or any part thereof shall not involve extension of the guarantee.

The warranty covers the replacement and free replacement of all parts that are defective in materials and components used in manufacturing and / or assembly of the apparatus.

The warranty does not cover any faults caused by accident, improper installation and use, electric shock (e.g. storms), connect a power other than that specified, reverse polarity in the diet, or claims due to deterioration in the external appearance of normal use, nor the amount or condition of the accessories.

Checking the accessories is the responsibility of the purchaser at the time of purchasing the device.

The warranty does not cover rechargeable batteries even if they are part of the equipment purchased as they are considered consumables, the impairment must be reported within a period of fifteen days from the date of purchase.

The warranty terms contained in this Certificate of Guarantee do not exclude, modify or restrict the statutory rights of the buyer by virtue of the laws in force at the time of purchase, but are added to them.

For a complete and detailed user manual, please refer to the official PDF document: Baofeng UV-9R EU User Manual (PDF).

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.