ANENJI ANJ-48V-60A

Contents

ANENJI MPPT Solar Charge Controller 60A

Model: ANJ-48V-60A

1. Safety Warnings and Cautions

Please read all manuals before installing. Only qualified professionals should install these controllers.

  • Keep the controller away from water. Do not use a wet towel to wipe the controller.
  • Ensure correct wiring; do not reverse wiring. Pay close attention to the terminal wiring sequence.
  • Operate the controller in an environmental temperature range of -20°C to +55°C. Avoid direct sunlight.
  • Ensure good heat dissipation around the controller.
  • Use pure copper wires and connect all polarities correctly.
  • The load output is only for DC loads less than 5A current.
  • Do not set any parameters if you are not a professional, as the controller works fine in default conditions (except for lithium batteries).
  • Important Note: The output terminal is for lamps only (12V system less than 60W, 24V/36V/48V system less than 100W). Connecting to other loads will cause damage. The battery output does not have reverse polarity protection.
12 Performance Features and Safety Icons
Figure 1: Key Performance Features and Safety Guidelines

2. Main Features

  • 60A MPPT solar charge controller
  • Intelligent Maximum Power Point Tracking (MPPT) technology
  • Built-in DSP controller with high performance
  • Automatic battery voltage detection for 12V/24V/36V/48V systems
  • Three-stage charging optimizes battery performance
  • Multi-function LCD display for easy monitoring
  • Overcharge protection and over-temperature protection
  • Reverse polarity protection for solar panels
  • Suitable for various battery types: sealed lead acid, vented gel, and lithium batteries
  • Easy to mount and install
Product Characteristics of ANENJI MPPT 60A Controller
Figure 2: Product Characteristics Overview

3. Package Contents

Please check the package contents upon receipt:

  • 1 x ANENJI MPPT Solar Charge Controller (60A)
  • 1 x User Manual (English)

4. Setup and Installation

4.1. Air Circuit Breaker and Wires Requirement

ItemRequirement
ModelsIcharger MPPT
Copper Wires6mm² x 2PCS
Air Circuit Breakers100A

4.2. Wire Connection Sequences

For the ICharger MPPT, it is recommended to connect two wires to two PV+ terminals and another two wires to two PV- terminals. The same method applies to BAT+ and BAT- connections.

4.3. Installation Steps

  1. Ensure the battery voltage is above 12V for the controller to boot up. Install an air circuit breaker between the controller and batteries. Turn off this circuit breaker, then connect the batteries to the controller with correct polarity.
  2. Install an air circuit breaker between the controller and PV modules. Turn off this circuit breaker, ensure the PV polarity is correct, then connect wires between the PV modules and the controller.
  3. Turn on the air circuit breaker between the controller and batteries.
  4. Turn on the air circuit breaker between the controller and PV modules.
Wiring Diagram for Solar Controller System
Figure 3: System Wiring Diagram (PV Array, Controller, Inverter, Battery, Load)
MPPT Solar Charge Controller Terminal Layout
Figure 4: Controller Terminal Connections (PV+, PV-, BAT+, BAT-, LOAD+, LOAD-)

5. Operation

5.1. LCD Display Indication

The multi-function LCD provides real-time system status. Use the navigation buttons to cycle through different display menus.

ANENJI MPPT 60A Controller Front View with LCD
Figure 5: Controller Front Panel with LCD Display

Display Introduction:

  • Menu1: Battery Voltage & Charge Current
  • Menu2: Battery SOC & Charge KW
  • Menu3: PV Voltage & Temperature
  • Menu4: Battery Type & System Voltage
  • Menu5: Load Mode (e.g., 7H for 7 hours)
  • Menu6: Error & Charge State

5.2. Press Key Operation

The controller features three buttons: ENTER, Up Arrow (▲), and Down Arrow (▼), and ESC.

Function KeySystem ModeOperationOperation Indication
ENTERView ModeLong PressEnter SET mode
Short Press (▲)Screen page up
Short Press (▼)Screen page down
Short Press (ESC)-
ENTERSetting ModeLong PressExit from setting & saving the present settings data
Short PressEnter the next setting page
Short Press (▲)Adjust the parameter by increase the value
Short Press (▼)Adjust the parameter by decrease the value
Short Press (ESC)Exit SET Mode without saving data
Press Key Operation Table
Figure 6: Detailed Key Operation Guide

5.3. Battery Type Setting

Navigate to the battery type setting menu to select the appropriate battery chemistry. Options include LI (Lithium), USE (User-defined), FLd (Flooded), GEL, and SEL (Sealed).

Battery Type Compatibility
Figure 7: Compatible Battery Types (Sealed Lead-Acid, Gel, Lithium)

5.4. System Voltage Setting

Set the system voltage (12V, 24V, 36V, 48V) or select AUTO for automatic detection. This setting is crucial for proper operation.

5.5. Parameter Setting

Advanced parameters can be adjusted for specific battery types (USE, LI, SEL/GEL/FLD). These include EQU Charge Volt, BST Charge Volt, FLD Charge Volt, BST-R Charge Volt, LRV Charge Volt, and LDV Charge Volt. Refer to the detailed manual pages for specific values and adjustment procedures.

Battery TypeSystem VoltEQUBSTFLDBST_RLRVLDV
GELAuto---14.2V13.8V13.2V12.6V11.1V
SELAuto14.6V14.4V13.8V13.2V12.6V11.1V
FLDAuto14.8V14.6V13.8V13.2V12.6V11.1V
USEAuto/12/24/36/48Defined by GEL
LI12/24/36/48Defined by GEL
Battery Charge Voltage Reference Table
Figure 8: Battery Charge Voltage Reference for Different Types

5.6. Working Mode

The controller operates in different modes depending on the solar input and battery state.

CodeWorking Mode
3.0Night mode, no charging
4.0MPPT mode
7.0Absorption mode
8.0Floating mode

6. Maintenance

  • Regularly inspect all wiring connections for tightness and corrosion.
  • Keep the controller clean and free from dust and debris. Use a dry cloth for cleaning.
  • Ensure adequate ventilation around the controller to prevent overheating. Check that the cooling fan (if present) is operating correctly.
  • Monitor the LCD display for any error codes or unusual readings.

7. Troubleshooting

7.1. Error Codes

If an error occurs, an error code will be displayed on the LCD. Refer to the table below for common error codes and their meanings.

CodeError
E00No Error
E01Battery over voltage
E02PV over voltage
E08Over-discharge
E20Device over heating
Error Code and Working Mode Table
Figure 9: Error Codes and Working Modes

8. Specifications

ItemParameter
ModelsIcharger MPPT
Charging mode3-stage: constant current (MPPT), constant voltage, floating
System voltage12/24/36/48V Auto
Max PV input power720W/12V; 1440W/24V; 2160W/36V; 2880W/48V
Max PV input voltage180 Voc
Battery voltage automatic recognition12V system (DC8.7V-DC15.5V); 24V system (DC16V-DC31V); 36V system (DC33V-DC41V); 48V system (DC42V-DC64V)
Overcharging protection voltage12V system (16V); 24V system (32V); 36V system (48V); 48V system (64V)
Limited current protection61A
Max efficiency≥98.1%
PV utilization≥99%
Auto Temperature Compensation-3mV/2V/°C
Protection Function
Temperature protection80°C
Fan-on temperature>45°C
Fan-off temperature<40°C
Properties
Size (mm)214 x 115 x 50
Net weight (Kg)1.1
Gross weight (Kg)1.2
Electromagnetic compatibilityAccord to EN61000, EN55022, EN55024
EnclosureIP21
Environmental temperature-20°C ~ +55°C
Storage temperature-40°C ~ +75°C
Technical Parameters Table
Figure 10: Detailed Technical Specifications
Product Dimensions
Figure 11: Product Dimensions (214mm H x 115mm W x 50mm D)

9. User Tips

  • Immediate Testing: It is highly recommended to test the controller immediately upon receipt to ensure it is fully functional.
  • Mode Monitoring: If using Lithium batteries, pay close attention to the working mode transitions (e.g., from 'Floating mode' 8.0 to 'MPPT mode' 4.0) in the morning. If the mode does not change automatically and charging does not start, manual intervention or further investigation into settings may be required.

10. Warranty and Support

For warranty claims or technical support, please contact your retailer or the manufacturer directly. Keep your purchase receipt as proof of purchase.

© 2024 ANENJI. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.