ANENJI ANJ-48V-60A

Contents

ANENJI 60A MPPT Solar Charge Controller

User Manual

Model: ANJ-48V-60A

1. Introduction

Thank you for choosing the ANENJI 60A MPPT Solar Charge Controller. This device is designed to efficiently manage power from your solar panels to charge your batteries, ensuring optimal performance and longevity of your solar power system. This manual provides essential information for the safe installation, operation, and maintenance of your controller.

For a complete reference, you may also consult the official user manual PDF: ANENJI MPPT Solar Charging Controller Product Manual (PDF).

2. Safety Information, Warnings, and Cautions

Please read all instructions carefully before installation and operation to prevent damage to the controller, batteries, or other components, and to ensure personal safety.

  • Professional Installation: Only qualified professionals should install these controllers.
  • Water Exposure: Keep the controller away from water. Do not use wet towels to wipe the controller.
  • Wiring: Ensure all wiring is correct and pay close attention to terminal wiring sequence. Do not reverse wiring.
  • Environmental Temperature: Operate the controller within an environmental temperature range of -20°C to +55°C. Avoid direct sunlight exposure.
  • Heat Dissipation: Maintain good heat dissipation around the controller. Ensure adequate airflow.
  • Wiring Material: Use pure copper wires for all connections and ensure all polarities are connected correctly.
  • Load Output: The load output terminal is designed for DC loads less than 5A current. Specifically, for lamps only (12V system less than 60W, 24V/36V/48V system less than 100W). Connecting to other loads or exceeding these limits will damage the controller.
  • Battery Output Polarity: The output for the battery does not have polarity reverse protection. Ensure correct polarity when connecting batteries.
  • Parameter Settings: Do not adjust any parameters if you are not a professional, as the controller operates effectively in its default condition, except for lithium batteries which may require specific configuration.
  • Screw Usage: Use only the provided screws for mounting. Using other screws or applying excessive torque can damage the internal PCB.

3. Product Features

  • 60A MPPT Solar Charge Controller
  • Intelligent Maximum Power Point Tracking (MPPT) technology for optimal energy harvest
  • Built-in DSP controller with high performance
  • Automatic battery voltage detection for 12V/24V/36V/48V systems
  • Three-stage charging (constant current, constant voltage, floating) optimizes battery performance and extends battery life
  • Multi-function LCD display for system status monitoring
  • Overcharge protection and over-temperature protection
  • Reverse polarity protection for solar panels
  • Suitable for various battery types: sealed lead acid, vented, gel, NiCd, and lithium batteries
  • Easy to mount and install
Product Characteristics of ANENJI 60A MPPT Solar Charge Controller

Image: Key product characteristics including MPPT technology, various protections, and battery compatibility.

4. Setup and Installation

4.1. Air Circuit Breaker and Wires Requirement

Item Requirement
Models Icharger MPPT
Copper Wires 6mm² x 2PCS
Air Circuit Breakers 100A

4.2. Wire Connection Sequences

For the ICharger MPPT, it is recommended to connect two wires to each PV+ terminal and two wires to each PV- terminal. The same method applies to BAT+ and BAT- connections.

Wiring Diagram for Solar Charge Controller

Image: General wiring diagram showing PV Array connected to the controller, which then connects to the battery and an inverter/load.

MPPT Solar Charge Controller Terminal Block Diagram

Image: Detailed terminal block diagram showing connections for PV+, PV-, BAT+, BAT-, LOAD+, and LOAD-.

4.3. Installation Steps

  1. Ensure the battery voltage is above 12V for the controller to boot up. Install an air circuit breaker between the controller and the batteries. Turn off this circuit breaker. Connect the batteries to the controller, ensuring correct polarity.
  2. Install an air circuit breaker between the controller and the PV modules. Turn off this circuit breaker. Ensure the PV polarity is correct. Connect the wires between the PV modules and the controller.
  3. Turn on the air circuit breaker connected between the controller and the batteries.
  4. Turn on the air circuit breaker connected between the controller and the PV modules.

5. Operating Instructions

5.1. LCD Display Introduction

The multi-function LCD display provides real-time information about your solar system. Navigate through the menus using the control buttons.

  • Menu 1: BAT Volt & Charge Curr (Battery Voltage and Charging Current)
  • Menu 2: BAT SOC & Charge KW (Battery State of Charge and Charging Kilowatts)
  • Menu 3: PV Volt & Temp (PV Voltage and Controller Temperature)
  • Menu 4: BAT Type & SYS Volt (Battery Type and System Voltage)
  • Menu 5: Load Mode (Load Operating Mode)
  • Menu 6: ERROR & Charge State (Error Codes and Charging Status)

5.2. Press Key Operation

The controller features three buttons: ENTER, UP (▲), and DOWN (▼), and ESC. Their functions vary depending on the mode.

Press Key Operation Table for Solar Charge Controller

Image: Table detailing button functions in View Mode and Setting Mode.

Function Key System Mode Operation Operation Indication
ENTER View Mode Long Press Enter SET mode
Short Press (▲) Screen page up
Short Press (▼) Screen page down
Setting Mode Long Press Exit from setting & saving the present settings data
Short Press (ENTER) Enter the next setting page
Short Press (▲/▼) Adjust the parameter by increase/decrease the value
ESC View/Setting Mode Short Press Exit SET Mode without saving data (or no function in View Mode)

5.3. Battery Type Setting

The controller supports various battery types. You can select from LI (Lithium), USE (User-defined), FLd (Flooded), SEL (Sealed), and GEL. Navigate to the battery type setting menu and select the appropriate type for your system.

Applicable Battery Types for Solar Charge Controller

Image: Visual representation of compatible battery types: Sealed lead-acid, Exhaust gel, and Lithium battery.

5.4. System Voltage Setting

The controller automatically detects system voltage (12V/24V/36V/48V). However, you can manually set it to AUTO, 12V, 24V, 36V, or 48V if needed, especially when using the 'USE' battery type.

5.5. Parameter Setting

Advanced users can adjust various charging parameters for specific battery types (USE, LI, SEL/GEL/FLD). These parameters include Equalization Charge Voltage (EQU), Boost Charge Voltage (BST), Float Charge Voltage (FLD), Boost-Return Voltage (BST_R), Low Voltage Reconnect (LRV), and Low Voltage Disconnect (LDV).

Caution: All steps for manual setting must be carried out when the PV modules are disconnected from the controller.

Battery Type System Volt EQU BST FLD BST_R LRV LDV
GEL Auto --- 14.2V 13.8V 13.2V 12.6V 11.1V
SEL Auto 14.6V 14.4V 13.8V 13.2V 12.6V 11.1V
FLD Auto 14.8V 14.6V 13.8V 13.2V 12.6V 11.1V
USE Auto/12/24/36/48 Defined by GEL (user-configurable) ---
LI 12/24/36/48 Defined by GEL (user-configurable) ---

5.6. Working Modes

Code Working Mode
3.0 Night mode, no charging
4.0 MPPT mode
7.0 Absorption mode
8.0 Floating mode

6. Maintenance

  • Cleaning: Periodically clean the controller's exterior with a dry cloth. Do not use wet cloths or solvents.
  • Connections: Regularly check all wiring connections to ensure they are tight and free from corrosion.
  • Heat Dissipation: Ensure the controller's ventilation openings are clear of dust and debris to maintain proper heat dissipation. The fan will activate when the internal temperature exceeds 45°C and turn off below 40°C.
  • Environment: Keep the controller in a dry, well-ventilated area, away from direct sunlight and corrosive gases.

7. Troubleshooting

The controller's LCD display will show error codes if a fault occurs. Refer to the table below for common error codes and their meanings.

Code Error
E00 No Error
E01 Battery over voltage
E02 PV over voltage
E08 Over-discharge
E20 Device over heating

8. Specifications

Item Parameter
Models Icharger MPPT
Charging Mode 3-stage: constant current (MPPT), constant voltage, floating
System Voltage 12V/24V/36V/48V Auto
Max PV Input Power 720W/12V; 1440W/24V; 2160W/36V; 2880W/48V
Max PV Input Voltage 180 Voc
Battery Voltage Automatic Recognition 12V system (DC8.7V-DC15.5V); 24V system (DC16V-DC31V); 36V system (DC33V-DC41V); 48V system (DC42V-DC64V)
Overcharging Protection Voltage 12V system (16V); 24V system (32V); 36V system (48V); 48V system (64V)
Limited Current Protection 61A
Max Efficiency ≥98.1%
PV Utilization ≥99%
Auto Temperature Compensation -3mV/2V/°C
Temperature Protection 80°C
Fan-on Temperature >45°C
Fan-off Temperature <40°C
Size (mm) 214 x 115 x 50
Net Weight (Kg) 1.1
Gross Weight (Kg) 1.2
Electromagnetic Compatibility Accord to EN61000, EN55022, EN55024
Enclosure IP21
Environmental Temperature -20°C ~ +55°C
Storage Temperature -40°C ~ +75°C
Dimensions of ANENJI 60A MPPT Solar Charge Controller

Image: Dimensional diagram showing the controller's width (115mm), height (214mm), and depth (50mm).

9. User Tips

  • Inspect Upon Arrival: Carefully inspect the product and its packaging immediately upon receipt for any signs of damage, missing parts, or water exposure. Report any issues to the seller promptly.
  • Verify Connections: Double-check all wiring connections before powering on the system to prevent damage from incorrect polarity or loose terminals.

10. Warranty and Support

ANENJI products are manufactured to high-quality standards. For any technical support or warranty inquiries, please contact your point of purchase or the official ANENJI support channels. Please retain your proof of purchase for warranty claims.

© 2023 ANENJI. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.