1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your Beitian M9 M10 GNSS Receiver. This device is a high-performance Global Navigation Satellite System (GNSS) receiver designed for precise positioning and navigation applications, supporting multiple constellations including GPS, BDS, Galileo, QZSS, and SBAS.
For a comprehensive technical overview, please refer to the official datasheet available here.
2. Product Overview
The Beitian GNSS receiver features a robust 'mushroom head' design with a built-in module antenna, making it suitable for various outdoor and industrial applications. It offers versatile connectivity through a DB9 serial port, allowing integration with a wide range of systems.
2.1 Components
- GNSS Receiver Unit (Mushroom Head)
- Integrated Antenna
- DB9 Serial Cable (3.0m length)
- Mounting Base (Magnetic bottom)
2.2 Product Views
3. Specifications
The following table details the technical specifications of the Beitian M9 M10 GNSS Receiver (BE-29D model):
| Feature | Description |
|---|---|
| Chip | M10050 |
| Receiver Type | GPS L1 C/A, QZSS L1 C/A/S, BDS B1I/B1C, Galileo E1B/C, SBAS L1 C/A (WAAS, EGNOS, MSAS, GAGAN) |
| Default Position System | GPS, BDS, GALILEO |
| Augmentation System | SBAS, QZSS |
| Channel | N/A |
| Tracking & Navigation Sensitivity | -166dBm |
| Reacquisition Sensitivity | -160dBm |
| Cold Start Sensitivity | -148dBm |
| Hot Start Sensitivity | -160dBm |
| Horizontal Position Accuracy | 2.0m CEP |
| Velocity Accuracy | 0.05m/s |
| Dynamic Heading Accuracy | 0.3 deg |
| Time Pulse Accuracy | RMS 30ns (99% 60ns) |
| Cold Start Acquisition | 27s |
| Hot Start Acquisition | 1s |
| Aided Start Acquisition | 1s |
| Baud Rate | 4800bps - 921600bps (default 38400bps) |
| Data Output Level | RS-232 level |
| Protocol | NMEA, UBX |
| NMEA Messages | RMC, VTG, GGA, GSA, GSV, GLL |
| Update Rate | 0.25Hz-18Hz (default 1Hz) |
| FLASH Memory | Configuration can be changed and saved |
| Time Pulse Signal Frequency | Configurable from 0.25 Hz to 10 MHz (default 1s, high level 100ms) |
| Operational Altitude Limit | 80,000m |
| Operational Velocity Limit | 500m/s |
| Operational Dynamics Limit | <4g |
| Power Voltage | DC 9.0V-34.0V (Typical: 12.0V) |
| Power Current | 30mA/12.0V |
| Dimension | Φ140mm*150.5mm |
| Weight | <1500g |
| Connector | DB9 serial female |
| Cable Length | 3.0m |
| Mounting | Magnetic bottom |
| Operating Temperature | -40 °C ~ +85°C |
| Wireless Function | Yes |
| PCB Included | Yes |
| Origin | Mainland China |
| GPS Type | Receiver & Antenna |
4. Setup and Installation
Proper installation is crucial for optimal performance of your GNSS receiver. Follow these steps for setup:
4.1 Physical Installation
- Mounting Location: Choose a location with a clear, unobstructed view of the sky to ensure maximum satellite visibility. The receiver features a magnetic bottom for easy attachment to metallic surfaces.
- Orientation: Ensure the 'mushroom head' dome is facing upwards.
4.2 Electrical Connection (DB9 Serial Port)
The receiver connects via a DB9 serial female connector. The pinout is as follows:
| PIN | Name | I/O | Description |
|---|---|---|---|
| 9 | VCC | I | DC Voltage 9.0V-34.0V, Typical: 12.0V |
| 2 | TX | O | RS-232 Serial Data Output |
| 3 | RX | I | RS-232 Serial Data Input |
| 5 | GND | G | Ground |
- Power Connection: Connect the VCC (Pin 9) to a DC power source within the 9.0V-34.0V range. Ensure proper polarity. Connect GND (Pin 5) to the system ground.
- Data Connection: Connect the TX (Pin 2) and RX (Pin 3) pins to your host device's serial port (e.g., computer, microcontroller) for data communication.
5. Operation
Once powered, the GNSS receiver will begin acquiring satellite signals. Data is output via the serial port in standard NMEA and UBX protocols.
5.1 Data Output Protocol
The receiver supports NMEA 0183 and UBX protocols. The default NMEA messages include RMC, VTG, GGA, GSA, GSV, and GLL. The default baud rate is 38400bps, but it can be configured from 4800bps to 921600bps.
The update rate is configurable from 0.25Hz to 18Hz, with a default of 1Hz. The configuration settings are stored in FLASH memory and will not be lost upon power cycle.
5.1.1 NMEA Message Descriptions
Below are examples and descriptions of common NMEA messages output by the receiver:
GNGGA - Global Positioning System Fix Data
Example: $GPGGA,092725.00,4717.11399,N,00833.91590,E,1,08,1.01,499.6,M,48.0,M,,*5B
| Field No. | Name | Description |
|---|---|---|
| 0 | xxGGA | GGA Message ID (xx = current Talker ID) |
| 1 | time | UTC time (hhmmss.ss) |
| 2 | lat | Latitude (ddmm.mmmmm) |
| 3 | NS | North/South indicator |
| 4 | lon | Longitude (dddmm.mmmmm) |
| 5 | EW | East/West indicator |
| 6 | quality | Quality indicator for position fix (1=Autonomous, 2=Differential, 4=RTK Fixed, 5=RTK Float, 6=Estimated/Dead reckoning) |
| 7 | numSV | Number of satellites used (range: 0-12) |
| 8 | HDOP | Horizontal Dilution of Precision |
| 9 | alt | Altitude above mean sea level (meters) |
| 10 | altUnit | Altitude units: M (meters) |
| 11 | sep | Geoid separation (difference between ellipsoid and mean sea level) |
| 12 | sepUnit | Geoid separation units: M (meters) |
| 13 | diffAge | Age of differential corrections (seconds) |
| 14 | diffStation | ID of station providing differential corrections |
| 15 | cs | Checksum |
| 16 | <CR><LF> | Carriage return and line feed |
GNGLL - Geographic Position - Latitude/Longitude
Example: $GPGLL,4717.11364,N,00833.91565,E,092321.00,A,A*60
| Field No. | Name | Description |
|---|---|---|
| 0 | xxGLL | GLL Message ID (xx = current Talker ID) |
| 1 | lat | Latitude (ddmm.mmmmm) |
| 2 | NS | North/South indicator |
| 3 | lon | Longitude (dddmm.mmmmm) |
| 4 | EW | East/West indicator |
| 5 | time | UTC time (hhmmss.ss) |
| 6 | status | Data validity status (A=valid, V=invalid) |
| 7 | posMode | Positioning mode (A=Autonomous, D=Differential, E=Estimated/Dead reckoning, F=RTK Float, R=RTK Fixed, N=No fix) |
| 8 | cs | Checksum |
| 9 | <CR><LF> | Carriage return and line feed |
GNGSA - GNSS DOP and Active Satellites
Example: $GPGSA,A,3,23,29,07,08,09,18,26,28,,,,,1.94,1.18,1.54,1*0D
| Field No. | Name | Description |
|---|---|---|
| 0 | xxGSA | GSA Message ID (xx = current Talker ID) |
| 1 | opMode | Operation mode (M=Manual, A=Automatic) |
| 2 | navMode | Navigation mode (1=No fix, 2=2D, 3=3D) |
| 3-14 | svid | Satellite ID (up to 12) |
| 15 | PDOP | Position Dilution of Precision |
| 16 | HDOP | Horizontal Dilution of Precision |
| 17 | VDOP | Vertical Dilution of Precision |
| 18 | systemId | NMEA defined GNSS System ID |
| 19 | cs | Checksum |
| 20 | <CR><LF> | Carriage return and line feed |
GNGSV - GNSS Satellites in View
Example: $GPGSV,3,1,09,09,,,17,10,,,40,12,,,49,13,,,35,1*6F
| Field No. | Name | Description |
|---|---|---|
| 0 | xxGSV | GSV Message ID (xx = current Talker ID) |
| 1 | numMsg | Total number of GSV messages |
| 2 | msgNum | Message number (1 to numMsg) |
| 3 | numSV | Number of known satellites in view |
| 4+ | svid | Satellite ID |
| 5+ | elv | Elevation (degrees, range: 0-90) |
| 6+ | az | Azimuth (degrees, range: 0-359) |
| 7+ | cno | Signal strength (C/N0, range: 0-99) |
| 8+ | signalId | NMEA defined GNSS Signal ID |
| ... | ... | Repeats for up to 4 satellites per message |
| Last | cs | Checksum |
| Last | <CR><LF> | Carriage return and line feed |
GNRMC - Recommended Minimum Specific GNSS Data
Example: $GPRMC,083559.00,A,4717.11437,N,00833.91522,E,0.004,77.52,091202,,,A,V*57
| Field No. | Name | Description |
|---|---|---|
| 0 | xxRMC | RMC Message ID (xx = current Talker ID) |
| 1 | time | UTC time (hhmmss.ss) |
| 2 | status | Data validity status (A=valid, V=invalid) |
| 3 | lat | Latitude (ddmm.mmmmm) |
| 4 | NS | North/South indicator |
| 5 | lon | Longitude (dddmm.mmmmm) |
| 6 | EW | East/West indicator |
| 7 | spd | Speed over ground (knots) |
| 8 | cog | Course over ground (degrees) |
| 9 | date | UTC date (ddmmyy) |
| 10 | mv | Magnetic variation value |
| 11 | mvEW | Magnetic variation E/W indicator |
| 12 | posMode | Positioning mode (A=Autonomous, D=Differential, E=Estimated/Dead reckoning, F=RTK Float, R=RTK Fixed, N=No fix) |
| 13 | navStatus | Navigational status indicator (V=Equipment not providing navigational status information) |
| 14 | cs | Checksum |
| 15 | <CR><LF> | Carriage return and line feed |
GNVTG - Track Made Good and Ground Speed
Example: $GPVTG,77.52,T,,M,0.004,N,0.008,K,A*06
| Field No. | Name | Description |
|---|---|---|
| 0 | xxVTG | VTG Message ID (xx = current Talker ID) |
| 1 | cogt | Course over ground, true (degrees) |
| 2 | cogtUnit | Course over ground units: T (degrees true) |
| 3 | cogm | Course over ground, magnetic (degrees) |
| 4 | cogmUnit | Course over ground units: M (degrees magnetic) |
| 5 | sogn | Speed over ground (knots) |
| 6 | sognUnit | Speed over ground units: N (knots) |
| 7 | sogk | Speed over ground (km/h) |
| 8 | sogkUnit | Speed over ground units: K (kilometers per hour) |
| 9 | posMode | Positioning mode (A=Autonomous, D=Differential, E=Estimated/Dead reckoning, F=RTK Float, R=RTK Fixed, N=No fix) |
| 10 | cs | Checksum |
| 11 | <CR><LF> | Carriage return and line feed |
5.1.2 NMEA 4.10 and Above Flags
The NMEA 4.10 standard introduces specific flags for status, quality, and position mode. Refer to the datasheet for a detailed breakdown of these flags.
6. Maintenance
The Beitian GNSS receiver is designed for durability and requires minimal maintenance. Follow these guidelines to ensure its longevity:
- Cleaning: Gently wipe the exterior with a soft, damp cloth. Avoid using harsh chemicals or abrasive materials.
- Environmental Protection: While robust, avoid prolonged exposure to extreme conditions beyond its specified operating temperature range (-40 °C to +85 °C).
- Cable Inspection: Periodically check the DB9 serial cable for any signs of wear, cuts, or damage. Replace if necessary.
7. Troubleshooting
If you encounter issues with your GNSS receiver, try the following troubleshooting steps:
- No Satellite Fix:
- Ensure the receiver has a clear, unobstructed view of the sky.
- Verify power supply is within the specified voltage range (9.0V-34.0V DC) and correctly connected.
- Check the cable connection for any damage or loose contacts.
- Allow sufficient time for cold start acquisition (up to 27 seconds).
- No Data Output:
- Confirm the serial port connection (TX/RX) to your host device is correct.
- Verify the baud rate setting on your host device matches the receiver's default (38400bps) or configured baud rate.
- Check the serial port settings (e.g., parity, data bits, stop bits) on your host device.
- Inaccurate Positioning:
- Relocate the receiver to an area with better sky visibility, away from tall buildings, dense foliage, or strong electromagnetic interference.
- Ensure the receiver is oriented correctly (dome facing upwards).
8. User Tips
- For applications requiring high precision, ensure the receiver is stationary during initial acquisition.
- When integrating with custom systems, always double-check the serial communication parameters (baud rate, data format) to avoid data corruption.
- Consider using a serial terminal program to monitor raw NMEA data during initial setup to confirm proper data output.
9. Frequently Asked Questions (FAQ)
- Q: What satellite systems does this receiver support?
- A: It supports GPS, BDS, Galileo, QZSS, and SBAS (WAAS, EGNOS, MSAS, GAGAN).
- Q: Can I change the data output rate?
- A: Yes, the update rate is configurable from 0.25Hz to 18Hz, with a default of 1Hz.
- Q: Is the configuration saved if power is removed?
- A: Yes, the receiver has FLASH memory to store configuration settings, so they are retained even after power loss.
10. Regulatory Information
This device complies with relevant industry standards for electronic equipment. Any modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment.