1. Introduction
Thank you for purchasing the SMSL VMV P2 MKII High-Resolution Headphone Amplifier. This device is designed to deliver exceptional audio performance for both headphones and as a preamplifier output. Featuring advanced technology such as a 99-piece Op-Amp parallel matrix, a fully balanced PLFC+ circuit, and a built-in GaN switching power supply, the VMV P2 MKII ensures a pristine and powerful listening experience. This manual provides essential information for setting up, operating, and maintaining your amplifier.
2. Safety Information
Please read and understand the following safety precautions before using the device to prevent injury to yourself or damage to the equipment.
- Power Supply: Use only the provided power cable and ensure the voltage matches the requirements specified on the unit.
- Water and Moisture: This product is not waterproof. Do not expose the unit to rain, moisture, dripping, or splashing. Do not place objects filled with liquids, such as vases, on the apparatus.
- Heat: Do not place the unit near heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Ensure adequate ventilation around the unit.
- Ventilation: Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
- Physical Shock: Avoid dropping, bumping, or subjecting the unit to strong vibrations.
- Cleaning: Unplug the unit from the power outlet before cleaning. Use a dry cloth only.
- Servicing: Do not attempt to service this product yourself. Refer all servicing to qualified service personnel.
- Cables: Avoid pulling or excessively bending connected cables. Ensure cables are securely connected but not under undue stress.
3. Package Contents
Please check that all items are present in the package:
- SMSL VMV P2 MKII Unit ×1
- Power Cable ×1
4. Product Overview
4.1. Front Panel

Figure 4.1: Front and Rear Panel Layout
- Input/Standby Button: Short press to cycle through inputs; long press to enter/exit standby mode.
- Output/Gain Button: Short press to cycle through output modes (Headphone/Pre-out); long press to cycle through gain levels (Low/Mid/High).
- Knob: Rotate to adjust volume.
- Gain Indicator Light: Indicates the current gain level.
- Standby Indicator Light: Indicates standby status.
- Output Indicator Light: Indicates the active output mode.
- Input Indicator Light: Indicates the active input.
- 4.4mm Headphone Jack: Balanced headphone output.
- 6.35mm Headphone Jack: Unbalanced headphone output.
- XLR Balanced Input: Balanced audio input.
4.2. Rear Panel
Refer to Figure 4.1 for the rear panel layout.
- RCA Input: Unbalanced audio input.
- XLR Balanced Input: Balanced audio input.
- USB Port: For firmware upgrades.
- RCA Pre-output: Unbalanced preamplifier output.
- XLR Pre-output: Balanced preamplifier output.
- AC IN (100V-240V AC): Power input connector.
4.3. Dimensions

Figure 4.2: Product Dimensions
The dimensions of the unit are approximately 280 × 51 × 235.7mm (Width × Height × Depth).
5. Setup
5.1. Connecting Audio Sources
- Balanced Input: Connect your audio source (e.g., DAC, CD player) to the XLR Balanced Input (10 or 12) on the rear panel using XLR cables.
- Unbalanced Input: Connect your audio source to the RCA Input (11) on the rear panel using RCA cables.
5.2. Connecting Headphones
The VMV P2 MKII offers multiple headphone outputs:
- 4.4mm Balanced: For headphones with a 4.4mm balanced connector (8).
- 6.35mm Unbalanced: For headphones with a 6.35mm (1/4 inch) unbalanced connector (9).
- XLR 4 Pin: For headphones with an XLR 4-pin balanced connector (located near 8, not explicitly numbered but visible in diagrams).
Ensure your headphones are compatible with the selected output type.
5.3. Connecting to External Amplifiers or Active Speakers (Preamplifier Output)
The VMV P2 MKII can also function as a preamplifier:
- Balanced Pre-output: Connect to your power amplifier or active speakers using XLR cables to the XLR Pre-output (15).
- Unbalanced Pre-output: Connect to your power amplifier or active speakers using RCA cables to the RCA Pre-output (14).
5.4. Power Connection
Connect the provided power cable to the AC IN (16) on the rear panel and then to a suitable power outlet (100V-240V AC).
6. Operation
6.1. Power On/Off (Standby)
- To power on the unit from standby, long press the Input/Standby Button (1).
- To put the unit into standby mode, long press the Input/Standby Button (1). The Standby Indicator Light (5) will illuminate.
6.2. Input Selection
Short press the Input/Standby Button (1) to cycle through the available audio inputs (XLR, RCA). The Input Indicator Light (7) will show the active input.
6.3. Volume Control
Rotate the Knob (3) clockwise to increase the volume and counter-clockwise to decrease it. The precision volume potentiometer ensures consistent left-right channel balance.
6.4. Gain Settings
Long press the Output/Gain Button (2) to cycle through the three gain levels: Low, Mid, and High. The Gain Indicator Light (4) will show the current setting. Choose the appropriate gain level for your headphones; Low gain is optimized for high-sensitivity In-Ear Monitors (IEMs).
6.5. Output Mode Selection
Short press the Output/Gain Button (2) to switch between Headphone Output and Preamplifier Output. The Output Indicator Light (6) will show the active output mode.
7. Maintenance
7.1. Cleaning
To maintain the appearance and performance of your VMV P2 MKII:
- Always disconnect the power cable before cleaning.
- Use a soft, dry, lint-free cloth to wipe the exterior surfaces.
- Do not use abrasive cleaners, waxes, or solvents (such as alcohol, vinegar, acetone) as they may damage the finish.
7.2. Storage
When not in use for extended periods, store the amplifier in a cool, dry, and dust-free environment. Avoid direct sunlight or extreme temperatures.
8. Troubleshooting
If you encounter any issues with your VMV P2 MKII, please refer to the following common troubleshooting steps:
- No Sound:
- Ensure the power cable is securely connected and the unit is powered on (not in standby).
- Check that the correct input source is selected.
- Verify that headphones or external amplifiers are properly connected to the correct output.
- Increase the volume using the Knob (3).
- Ensure the correct output mode (Headphone or Pre-out) is selected.
- Distorted Sound:
- Check the audio cables for damage or loose connections.
- Ensure the input source is not sending an excessively high signal that could cause clipping.
- Try a different gain setting. High gain with sensitive headphones might introduce distortion.
- Channel Imbalance:
- The VMV P2 MKII features a high-precision volume potentiometer designed to minimize channel imbalance. If you experience imbalance, ensure your audio source and cables are functioning correctly.
- Test with different headphones or cables to isolate the issue.
- Unit Not Responding:
- Disconnect the power cable, wait for 30 seconds, and then reconnect it to perform a hard reset.
8.1. Comprehensive Protection Features
The VMV P2 MKII includes multiple built-in protection circuits to safeguard your equipment and headphones:

Figure 8.1: Protection Features
- DC Protection: Blocks harmful DC signals, protecting your headphones.
- Over-Voltage Protection: Monitors input voltage, preventing over-voltage damage.
- Over-Load Protection: Limits output current, preventing overload.
- Temperature Protection: Monitors operating temperature, preventing overheating.
In critical situations, the output will automatically cut off to protect your valuable headphones.
9. User Tips
- Optimizing Gain: For high-sensitivity In-Ear Monitors (IEMs), start with the 'Low' gain setting to ensure a clean, noise-free background and prevent accidental over-driving.
- Preamplifier Functionality: Utilize the dedicated preamplifier outputs (XLR or RCA) to integrate the VMV P2 MKII into a larger audio system with power amplifiers or active speakers, leveraging its Hi-End circuit quality.
- Firmware Updates: Keep an eye on the official SMSL website for potential firmware updates. The USB port allows for easy upgrades to continuously unlock new optimizations and features.
10. Specifications
| Feature | Specification |
|---|---|
| Product Name | SMSL VMV P2 MKII High-Resolution Headphone Amplifier |
| Inputs | Balanced ×1, Unbalanced ×1 |
| Headphone Outputs | 4.4mm Balanced ×1, XLR 4 Pin ×1, 6.35mm Unbalanced ×1 |
| Pre-Outputs | Balanced ×1, Unbalanced ×1 |
| Output Power (Balanced) | 14W×2 (16Ω) / 8W×2 (32Ω) / 1W×2 (300Ω) / 500mW×2 (600Ω) |
| Output Power (Unbalanced) | 4W×2 (16Ω) / 2W×2 (32Ω) / 300mW×2 (300Ω) / 150mW×2 (600Ω) |
| SNR | 135dB |
| Dynamic Range | 135dB |
| THD+N | 0.00006% (−123dB, 1kHz, 32Ω) |
| Input Impedance | 47kΩ |
| AMP Output Impedance | Near 0Ω |
| Pre-Output Impedance | Balanced 44Ω / Unbalanced 22Ω |
| Frequency Response | 20Hz–100kHz (−0.5dB) |
| Power Consumption | <100W |
| Dimensions (W×H×D) | 280 × 51 × 235.7mm |
| Weight | 3.25kg (7.16 lbs) |
10.1. Performance Graphs

Figure 10.1: THD+N Performance

Figure 10.2: SNR Performance

Figure 10.3: Frequency Response

Figure 10.4: Dynamic Range
11. Firmware Upgrades
The VMV P2 MKII is equipped with a dedicated USB port (13) to support future firmware upgrades. These upgrades can continuously unlock new optimizations and features, enhancing the performance and functionality of your amplifier. Please visit the official SMSL website for information on available firmware updates and instructions on how to perform them.
12. Warranty and Support
For detailed warranty information, terms, and conditions, please refer to the official SMSL website or the documentation provided with your purchase. General warranty coverage typically includes manufacturing defects for a specified period from the date of purchase.
Warranty Exclusions generally include:
- Damage caused by accidents, misuse, abuse, neglect, or unauthorized modifications.
- Damage from improper operation or maintenance, connection to improper voltage supply, or attempted repair by anyone other than an authorized service center.
- Normal wear and tear.
For technical support, service inquiries, or to report any issues, please contact SMSL customer service through their official channels. You may also find additional information and support resources on the official SMSL website.
Additional Resources:
A PDF version of the user manual may be available for download. Please check the official SMSL product page or the following link for the PDF manual: SMSL VMV P2 MKII User Manual (PDF)