KORAD KD3003D/KD3005D

Contents

KORAD KD3003D/KD3005D Linear DC Power Supply User Manual

Adjustable for Laptop/Phone Repair

1. Introduction

This manual provides essential information for the safe and effective use of your KORAD KD3003D or KD3005D Linear DC Power Supply. These adjustable power supplies are designed for precision applications such as laptop and phone repair, offering stable and reliable power output. Please read all instructions carefully before operation to ensure safety and prevent damage.

KORAD KD3003D/KD3005D Linear DC Power Supply front view with display and controls.
Front view of the KORAD KD3003D/KD3005D Linear DC Power Supply, showing the digital display and control knobs.

2. Safety & Warnings

Read all instructions before use to ensure safety and prevent damage.

  • WARNING: Keep this product and its small parts out of reach of children under 3 years old due to choking hazard.
  • WARNING: Do not disassemble, modify or repair this product by yourself. Unauthorized modifications will void the warranty and may cause safety hazards.
  • WARNING: Do not expose the product to water, moisture, extreme temperatures (below 0°C or above 40°C) or direct sunlight for long periods.
  • WARNING: Stop using the product immediately if it shows signs of damage, cracking, overheating or malfunction.
  • WARNING: Keep the product away from open flames, flammable materials and high-voltage sources.
  • WARNING: Please use only the original charging cable and adapter. Do not overcharge the battery.
  • WARNING: Wear protective gloves when installing sharp-edged parts.
Rear view of the KORAD power supply showing the fan, power input, and warning labels.
Rear view of the power supply, highlighting the fan, power input, and important warning labels.

3. Product Features

The KORAD KD series power supplies offer a range of advanced features for precise and safe operation:

  • Full Power Output: Designed for long load times.
  • Digital Encoder Adjustment: Provides both coarse and fine tuning for voltage and current.
  • Smart Temperature-Controlled Fan: The fan operates at low speed when the unit is on, with its speed adjusting based on temperature to ensure optimal cooling.
  • Constant Voltage (CV) and Constant Current (CC) Modes: Automatically switches between modes based on load conditions.
  • High-Resolution Four-Digit Display: Offers precise readings with 10mV/1mA resolution.
  • Pure Copper Transformer: Ensures low noise and low ripple output.
  • LOCK Function: Prevents accidental changes to settings during operation.
  • Comprehensive Protection: Includes short circuit protection and overcurrent protection (OCP).
Diagram showing the key features of the KORAD KD series power supply.
Detailed diagram illustrating the main features of the KD series power supplies.

4. Setup

  1. Preparation: Remove all protective films and packaging materials from the product. Check that all parts are complete and undamaged.
  2. Installation/Setup: Follow the product-specific installation guide to assemble or connect the product correctly. Ensure the power supply is placed on a stable, level surface with adequate ventilation.
  3. Power Connection: Connect the provided power cord to the AC input on the rear of the unit and then to a suitable power outlet.
  4. Output Connections: Connect your test leads to the output terminals (red for positive, black for negative, green for ground).
KORAD KD3003D power supply with included accessories: power cord and test leads.
The KD3003D model shown with its standard accessories, including the power cord and test leads.

5. Operating Instructions

This section details the basic operation of your KORAD DC Power Supply.

5.1 Power On/Off

Press the 'POWER' button on the front panel to turn the unit on or off.

5.2 Adjusting Voltage and Current

  • Voltage Adjustment: Use the 'VOLTAGE' knob to set the desired output voltage. Push the knob to switch between coarse and fine adjustment modes. Rotate to change the value.
  • Current Adjustment: Use the 'CURRENT' knob to set the desired output current limit. Push the knob to switch between coarse and fine adjustment modes. Rotate to change the value. The power supply will not output more than the set current limit.

5.3 Lock Function

To prevent accidental changes to the voltage settings, press and hold the 'VOLTAGE' knob to activate the lock function. The 'LOCK' indicator light will illuminate. To unlock, press and hold the 'VOLTAGE' knob again.

5.4 Overcurrent Protection (OCP)

The unit features Overcurrent Protection (OCP). When OCP is enabled and a short circuit or overcurrent condition occurs, the power supply will automatically stop outputting power to protect the connected device and itself. To enable OCP, press and hold the 'CURRENT' knob. The 'OCP' indicator light will illuminate. To reset after an OCP event, briefly adjust the current knob or cycle the power.

5.5 Visual Demonstration

This video demonstrates the adjustment of voltage and current, the lock function, and the overcurrent protection (OCP) feature of the KORAD power supply.
KORAD power supply connected to a multimeter to measure voltage output.
Voltage measurement setup using the KORAD power supply and a multimeter.
KORAD power supply connected to a multimeter to measure large current output.
Demonstration of large current measurement from the KD series power supply using a multimeter.
KORAD power supply connected to a multimeter to measure small current output.
Demonstration of small current measurement from the KD series power supply using a multimeter.

6. Maintenance & Storage

  • Cleaning: Turn off the device before cleaning. Use a soft, lint-free cloth to wipe the surface. Do not use harsh chemicals or abrasive cleaners.
  • Storage: Store in a dry place at room temperature (15°C - 35°C).
  • Long-term Storage: If not used for a long time, charge the device to 50% every 3 months (applicable to battery-powered products).

7. Troubleshooting

If you encounter issues with your KORAD power supply, consider the following general troubleshooting steps:

  • No Power: Ensure the power cord is securely connected to both the unit and the power outlet. Check the power switch.
  • No Output Voltage/Current: Verify that the output terminals are correctly connected to your load. Check if the OCP (Overcurrent Protection) is triggered (OCP light on). If so, clear the fault and briefly adjust the current knob or cycle power. Ensure the voltage and current settings are not at zero.
  • Unstable Output: Check for loose connections. Ensure the load is within the specified voltage and current ranges.
  • Unit Overheating: Ensure adequate ventilation around the unit. Check if the fan is operating. If overheating persists, reduce the load or discontinue use.
  • Lock Function Engaged: If controls are unresponsive, check if the 'LOCK' indicator is on. Press and hold the 'VOLTAGE' knob to unlock.

For more detailed troubleshooting or persistent issues, please refer to the official user manual PDF or contact customer support.

8. Specifications

The following table provides the technical specifications for the KORAD KD3003D and KD3005D models. Note: The following indicators are for a 20-minute warm-up period, at an ambient temperature of 25°C ± 5°C.

Table of technical specifications for KORAD KD3003D and KD3005D power supplies.
Technical specifications for KD3003D and KD3005D models.
FeatureKD3003DKD3005D
Voltage Range0-30V0-30V
Current Range0-3A0-5A
Load Effect (Voltage)≤0.01%+2mV≤0.01%+2mV
Load Effect (Current)≤0.1%+5mA≤0.1%+10mA
Power Effect (Voltage)≤0.01%+3mV≤0.01%+3mV
Power Effect (Current)≤0.1%+3mA≤0.1%+3mA
Output Resolution (Voltage)10mV10mV
Output Resolution (Current)1mA1mA
Setting Accuracy (Voltage)≤0.5%+20mV≤0.5%+20mV
Setting Accuracy (Current)≤0.5%+5mA≤0.5%+10mA
Ripple (20-20M) (Voltage)≤1mVrms≤2mVrms
Ripple (20-20M) (Current)≤3mArms≤3mArms
Output Temperature Coefficient (Voltage)≤150ppm≤150ppm
Output Temperature Coefficient (Current)≤150ppm≤150ppm
Return Value Resolution (Voltage)10mV10mV
Return Value Resolution (Current)1mA1mA
AccessoriesUser manual*1, Power cord*1
Dimensions (L*W*H)260mm * 110mm * 160mm
Weight4.1kg4.9kg

8.1 Model Comparison

The following table compares the features of different KORAD power supply models, including KD-D, KA-D, and KA-DS series.

Comparison table of KORAD power supply models: KD-D, KA-D, KA-DS series, detailing current error, lock function, overcurrent protection, short circuit protection, overvoltage protection, data storage, output start/stop, and power display.
Comparison of features across KD-D, KA-D, and KA-DS series models.
  • KA-P Series: Features a communication interface for PC software connection. Other functions are similar to KA-D.
  • KA-PS Series: Features a communication interface for PC software connection. Other functions are similar to KA-DS.

9. User Tips

No specific user tips were available from reviews or Q&A for this product. Always ensure proper ventilation and use appropriate safety measures when working with electrical equipment.

10. Compliance Information

This product complies with the relevant EU legislation, including Machinery Regulation (EU) 2023/1230. This product bears the CE, UKCA and FC marks.

11. Disposal & Recycling

This symbol indicates that this product should not be treated as household waste. According to the WEEE Directive (2012/19/EU), it must be disposed of at an appropriate electronic waste collection point for recycling to prevent potential negative consequences for the environment and human health.

12. Warranty & Support

For warranty information and technical support, please refer to the documentation included with your product or contact the manufacturer directly. The manufacturer's contact information is:

  • Manufacturer: Changsha Sematic E-commerce Co., Ltd.
  • Email: 364824110@qq.com
  • Phone: +86 13627416939

An official user manual in PDF format is available for download: User manual (PDF)

© 2023 KORAD. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.