1. Introduction
This manual provides detailed instructions for the safe and efficient operation of your AHT JH3-004 3-in-1 Vacuum Casting & Melting Furnace. This versatile machine combines high-temperature melting, vacuum degassing, and precision jewelry casting into a single unit, designed for working with gold, silver, copper, brass, and other low-melting alloys. Please read this manual thoroughly before initial use to ensure proper setup, operation, and maintenance.
Video: Overview of the AHT JH3-004 3-in-1 Vacuum Casting & Melting Furnace in operation.
2. Safety Information
⚠ WARNING: This product can expose you to chemicals including lead and cadmium, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
General Safety Precautions:
- Always wear appropriate personal protective equipment (PPE), including heat-resistant gloves, safety glasses, and a face shield, when operating the furnace.
- Ensure the work area is well-ventilated to prevent inhalation of fumes.
- Do not touch hot surfaces. Allow the machine to cool completely before handling components.
- Keep flammable materials away from the furnace during operation.
- Ensure the power supply matches the machine's voltage requirements (110V or 220V depending on model).
- Never leave the machine unattended during operation.
- Keep children and unauthorized personnel away from the equipment.
- Disconnect power before performing any maintenance or cleaning.
3. Product Components & Accessories
The AHT JH3-004 unit integrates several key components for its 3-in-1 functionality. Familiarize yourself with each part and the included accessories.

Figure 3.1: Main components of the AHT JH3-004 unit, including Melting Furnace, Flask, Vacuum Chamber, Power Socket, Melting Switch, Temperature Controller, Vacuum Gauge, and Pressure Adjustment Valve.
Main Unit Features:
- Melting Furnace: For high-temperature melting of metals.
- Vacuum Chamber: Used for vacuum degassing and casting.
- Temperature Controller: Digital display for precise temperature setting and monitoring.
- Melting Switch: On/Off control for the melting function.
- Vacuum Gauge: Monitors vacuum levels.
- Pressure Adjustment Valve: Controls vacuum release.
- Vacuum Pump Connection Port: For connecting an external vacuum pump (not included).
- Power Socket: Main power input.
Included Accessories:

Figure 3.2: Standard accessories included with the AHT JH3-004.
- 3-inch Steel Bell
- Vacuum Hood
- Hose
- Pliers
- 2 kg Crucible
- Steel Bell Set
- Rubber Sole
- Power Cable
4. Technical Specifications
| Feature | Specification |
|---|---|
| Product Type | 3-in-1 Vacuum Casting & Melting Furnace |
| Model | JH3-004 |
| Power | 1500W |
| Voltage Options | 110V or 220V (SKU dependent) |
| Max Temperature | 1150℃ / 2102℉ |
| Crucible Capacity | 2 kg |
| Core Functions | Smelting, Vacuum Degassing, Jewelry Casting |
| Compatible Metals | Gold, Silver, Copper, Brass, Low-melting Alloys |
| Control System | Digital Temperature Control (PID Smart Control) |
| Certification | Patented Design (PAT: 202130317186.4) |
| Dimensions (L x W x H) | 16.3" x 14.2" x 20" (approx. 41.4cm x 36.1cm x 50.8cm) |
| Weight | 44 lbs (approx. 20 kg) |
| Air Flow (Vacuum) | 4 CFM (for unit) / Recommended 8 CFM for 4L Chamber (external pump) |
| Ultimate Vacuum (external pump) | 60 Microns |
| Motor Power (external pump) | 3/4 HP |
| Oil Capacity (external pump) | 22 fl. oz. (650 mL) |
| Origin | Mainland China |
Note: An external vacuum pump is required for vacuum functions and is NOT included with the unit. Refer to the recommended specifications for optimal performance.
5. Setup Instructions
- Unpacking: Carefully remove all components from the packaging. Inspect for any damage.
- Placement: Place the unit on a stable, heat-resistant, and level surface in a well-ventilated area. Ensure adequate clearance around the machine for heat dissipation.
- Power Connection: Connect the provided power cable to the power socket on the unit and then to a grounded electrical outlet matching the machine's voltage (110V or 220V).
- Vacuum Pump Connection (if applicable):
- An external vacuum pump is required for vacuum degassing and casting. This pump is NOT included.
- Connect the provided hose to the "Vacuum pump connection port" on the unit and to your external vacuum pump.
- Ensure all connections are secure to prevent air leaks.

Figure 5.1: Vacuum control panel showing the vacuum pressure gauge, vacuum release, and vacuum pump connection port.
- Initial Checks: Before first use, ensure all switches are in the "OFF" position and all components are correctly assembled.
6. Operating Instructions
6.1. Metal Melting
- Place the 2 kg crucible into the melting furnace chamber.
- Using the provided scoop, carefully add the metal (gold, silver, copper, brass, or low-melting alloys) into the crucible.
- Close the melting furnace lid securely.
- Turn on the main power switch.
- Use the digital temperature controller to set the desired melting temperature (Set Value, SV). The Process Value (PV) will show the current temperature.

Figure 6.1: Digital Temperature Control interface. A steady light indicates heating in progress, a blinking light indicates the set temperature has been reached.
- Flip the "Smelting Switch" to "ON". The furnace will begin heating.
- Monitor the temperature display. Once the blinking light indicates the set temperature is reached, the metal should be molten.
- Using heat-resistant pliers and gloves, carefully remove the crucible with the molten metal.

Figure 6.2: Illustration of the metal melting process within the furnace.
6.2. Vacuum Degassing & Jewelry Casting
This process helps eliminate bubbles for flawless casting results.

Figure 6.3: The 3-in-1 functionality: Vacuum Extraction, High-Temp Melting, and Vacuum Extraction for Rapid Mold Fill.
- Prepare your casting flask/mold.
- Place the casting flask/mold under the vacuum hood on the casting chamber.
- Place the vacuum hood over the flask/mold, ensuring a tight seal.
- Turn on your external vacuum pump.
- Engage the vacuum by turning the "Vacuum release" toggle lever to the "Vacuum" position. The vacuum gauge will show the pressure dropping.
- Once the desired vacuum level is reached (e.g., 60 Microns), carefully pour the molten metal from the crucible into the casting flask/mold. The vacuum will assist in rapid mold fill and bubble elimination.
- After pouring, maintain the vacuum for a short period (e.g., 30-60 seconds) to allow the metal to solidify under vacuum.
- Release the vacuum by turning the "Vacuum release" toggle lever to the "Release" position.
- Carefully remove the vacuum hood and the cast item.
- Allow the cast item to cool. For faster cooling, you may submerge the mold in water (ensure the metal has solidified sufficiently to prevent thermal shock damage to the mold).
- Once cooled, carefully remove the semi-finished jewelry from the mold.
- Polish the item as needed to achieve the desired finish.

Figure 6.4: Step-by-step visual guide for casting a jewelry model, from placing the flask in the vacuum hood to polishing the finished piece.

Figure 6.5: Example of molten metal being cast into a bar mold.
7. Maintenance
Regular maintenance ensures the longevity and optimal performance of your AHT JH3-004 unit.
- Cleaning: After each use, allow the unit to cool completely. Wipe down exterior surfaces with a dry, soft cloth. Remove any metal residue from the melting chamber and casting area.
- Crucible Inspection: Regularly inspect the crucible for cracks or excessive wear. Replace if damaged to prevent metal leakage.
- Vacuum System: Check the hose and connections for any signs of wear or leaks. Ensure the vacuum pump (external) is maintained according to its manufacturer's instructions, including oil changes if applicable.
- Storage: Store the unit in a clean, dry environment away from dust and moisture when not in use.
8. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Furnace not heating | No power, Smelting Switch OFF, faulty heating element. | Check power connection, ensure switch is ON. If problem persists, contact support. |
| Inconsistent melting temperature | Incorrect temperature setting, worn thermocouple, unstable power. | Verify temperature settings. Ensure stable power supply. Contact support if thermocouple is suspected. |
| Poor vacuum / Bubbles in casting | Loose vacuum hose connection, faulty external vacuum pump, worn rubber seals, vacuum release valve open. | Check all hose connections. Inspect rubber seals for wear. Ensure vacuum release valve is in "Vacuum" position. Verify external vacuum pump functionality. |
| Metal not pouring smoothly | Metal not fully molten, crucible spout blocked. | Increase melting temperature or time. Ensure crucible is clean and free of blockages. |
9. User Tips
While no specific user reviews or Q&A were provided, here are some general tips for optimal use:
- Pre-heat Molds: For best casting results, pre-heat your casting molds/flasks before pouring molten metal. This helps prevent thermal shock and ensures better metal flow.
- Crucible Care: Avoid using the same crucible for different types of metals to prevent contamination. Clean crucibles thoroughly after each use.
- Vacuum Pump Quality: Invest in a high-quality external vacuum pump with sufficient flow rate and ultimate vacuum for the best degassing and casting performance.
- Practice: If new to metal casting, start with less valuable metals to practice the process and refine your technique before working with precious materials.
10. Warranty & Support
For warranty information, technical support, or service inquiries, please refer to the documentation provided at the time of purchase or contact your vendor directly. Keep your purchase receipt as proof of purchase.
Disclaimer: This manual is intended for informational purposes only. The manufacturer and seller are not responsible for any damage or injury caused by improper use or modification of the product.