1. Introduction
This manual provides essential information for the installation, operation, and maintenance of your SUMRY HGX 4KW 24V Hybrid Solar Inverter. This pure sine wave inverter is designed for off-grid solar systems, featuring an MPPT solar charge controller and an LCD touch display for easy monitoring and control. Please read this manual thoroughly before installation and use to ensure safe and efficient operation.
Figure 1: SUMRY HGX 4KW 24V Hybrid Solar Inverter
2. Key Features
- Pure Sine Wave Output: Ensures compatibility with a wide range of electronic devices.
- Integrated MPPT Solar Charge Controller: Maximizes power harvest from solar panels.
- Hybrid Functionality: Operates in off-grid mode, capable of working without a battery.
- LCD Touch Display: User-friendly interface for monitoring system status and settings.
- Wide Battery Compatibility: Supports various battery types including Flooded, Gel, Lithium-iron phosphate, Lithium-ion, AGM/Sealed, and user-defined custom batteries.
- Communication Ports: Equipped with RS458/RS232 for external communication.
- Robust Design: Constructed with an aluminum alloy casing for durability.
Figure 2: Inverter Front Panel with LCD Display and Controls
3. Installation and Setup
3.1 Safety Precautions
- Ensure all power sources are disconnected before installation.
- Only qualified personnel should perform electrical installations.
- Wear appropriate personal protective equipment (PPE).
- Install the inverter in a well-ventilated area, away from flammable materials.
3.2 Physical Connections
Refer to the diagram below for proper connection of the inverter's rear panel ports.
Figure 3: Rear Panel Connection Diagram
- Battery Input: Connect your 24V battery bank to the designated battery terminals (+ and -). Ensure correct polarity.
- AC Output: Connect your AC loads (appliances) to the AC output terminals.
- RS458/RS232 Communication Port: Use this port for connecting to monitoring software or other communication devices.
- AC Input: Connect the grid AC power source (if applicable for hybrid operation) to the AC input terminals.
- PV Input: Connect your solar panel array to the PV input terminals (+ and -).
3.3 Solar Photovoltaic Panel Wiring
The inverter supports both series and parallel configurations for solar panels. Ensure the total voltage and current of your PV array remain within the inverter's specifications.
Figure 4: Solar Panel Series/Parallel Wiring Methods
- Series Connection: Increases the voltage of the system. The total voltage must be less than the hybrid inverter's maximum PV input voltage (Voc/inverter). For example, 6 panels of 41.92V in series result in 251.52V.
- Parallel Connection: Increases the current of the system. The total current should not exceed the maximum PV input current of the hybrid inverter. For example, 2 strings of 3 panels (each string in series) connected in parallel, with each string having 10.35A, results in 20.7A total current.
- Important: The entire photovoltaic system should use the same type of photovoltaic panel.
- PV Cable Dimensions: Recommended cable dimensions are 6-8A/mm².
3.4 Battery Compatibility
The SUMRY HGX inverter is compatible with a variety of 24V battery types. Select the appropriate battery type in the inverter's settings for optimal charging and discharge performance.
Figure 5: Compatible Battery Types
Supported battery types include:
- Flooded (FLD)
- Gel
- Lithium-iron phosphate (LI)
- Lithium-ion (LI)
- AGM/Sealed (SLD)
- User custom Battery (USER)
4. Operation
4.1 Powering On/Off
- Ensure all connections are secure before powering on.
- Turn on the battery breaker (if installed).
- Turn on the PV array breaker (if installed).
- Press the ON/OFF button on the inverter's front panel to power on the unit.
- To power off, reverse the sequence: turn off the inverter, then the PV breaker, and finally the battery breaker.
4.2 LCD Touch Display
The LCD touch display provides real-time information about the inverter's status, battery charge, PV input, AC output, and various settings. Use the touch interface to navigate menus and adjust parameters such as battery type, charging current, and output voltage range.
Figure 6: Typical Inverter Applications
5. Maintenance
- Regular Cleaning: Keep the inverter's vents and surfaces clean and free from dust to ensure proper heat dissipation. Use a dry, soft cloth.
- Connection Checks: Periodically inspect all electrical connections (battery, PV, AC) for tightness and signs of corrosion.
- Battery Health: Monitor battery voltage and health, especially for lead-acid batteries, to ensure optimal performance and lifespan.
- Environmental Conditions: Ensure the inverter is operating within its specified temperature and humidity ranges.
6. Troubleshooting
If the inverter is not functioning as expected, perform the following basic checks:
- No Power/Display Off:
- Check battery connections and ensure the battery is charged.
- Verify the ON/OFF switch is in the 'ON' position.
- Inspect all wiring for loose connections or damage.
- No AC Output:
- Check AC output connections to loads.
- Ensure the inverter is not in an overload condition (check LCD display).
- Verify battery voltage is sufficient.
- No PV Charging:
- Check PV panel connections and ensure they are clean and unobstructed.
- Verify PV input voltage is within the MPPT range (55-280VDC).
- Ensure the PV breaker is 'ON'.
For persistent issues, consult a qualified technician or contact customer support.
7. Specifications
| Feature | Specification |
|---|---|
| Model Number | HGX 4KW 110V |
| Type | Hybrid Solar Inverter |
| Material | Aluminum alloy |
| Origin | Mainland China |
| Power Rating | 4000W |
| Battery Voltage | 24VDC |
| AC Input Voltage | 110/120V |
| Selectable Voltage Range | 90-140 VAC |
| Wave Form | Pure Sine Wave |
| Frequency Range | 50Hz/60Hz |
| MPPT Voltage Range | 55-280VDC |
| Max PV Array Power | 5600W |
| Max AC Charge Current | 110A |
| Supported Battery Types | Lead acid battery, lithium battery, Lifepo4 battery (Flooded, Gel, Lithium-iron phosphate, Lithium-ion, AGM/Sealed, User custom) |
| Package Dimensions (L x W x H) | 42cm x 66cm x 88cm |
| Package Weight | 25.0 kg |
8. Warranty and Support
The SUMRY HGX 4KW 24V Hybrid Solar Inverter comes with a 1-year warranty from the date of purchase. This warranty covers manufacturing defects and malfunctions under normal use conditions.
For technical support, troubleshooting assistance, or warranty claims, please contact your retailer or the manufacturer's customer service. Ensure you have your purchase receipt and product model number readily available.
9. User Tips
- Always ensure proper ventilation around the inverter to prevent overheating.
- Regularly check the LCD display for any error codes or warnings.
- For optimal battery life, configure the correct battery type and charging parameters in the inverter settings.
- Consider using appropriate surge protection devices for both AC and DC inputs to protect the inverter from electrical spikes.
10. Frequently Asked Questions (FAQ)
- Q: Can this inverter work without batteries?
- A: Yes, the SUMRY HGX 4KW Hybrid Solar Inverter is designed to work in off-grid mode and can operate without a battery, directly powering loads from solar panels or the grid (if connected).
- Q: What is the maximum PV input voltage?
- A: The MPPT voltage range is 55-280VDC, and the maximum PV array power is 5600W. Ensure your solar panel array's open-circuit voltage (Voc) does not exceed the inverter's maximum input voltage.
- Q: How do I select the battery type?
- A: The battery type can be selected via the LCD touch display menu. Refer to the operating section of this manual for navigation instructions. It supports Flooded, Gel, Lithium-iron phosphate, Lithium-ion, AGM/Sealed, and user-defined custom batteries.