NEEWER 10093452

Contents

NEEWER C Stand with Boom Arm & Sliding Legs Instruction Manual

Model: 10093452

Introduction

Thank you for choosing the NEEWER C Stand with Boom Arm and Sliding Legs. This professional-grade light stand is constructed from 100% stainless steel, designed for exceptional stability and versatility in various shooting environments. It features an adjustable center column, a flexible boom arm, and unique sliding legs to adapt to uneven surfaces. This manual provides detailed instructions for assembly, operation, maintenance, and troubleshooting to ensure optimal performance and longevity of your equipment.

NEEWER C Stand with Boom Arm and Sliding Legs
A full view of the NEEWER C Stand assembled with its boom arm and grip heads.

Package Contents

Please verify that all the following components are included in your package:

  • 1 x Upgraded C-Stand
  • 1 x Holding Arm (Boom Arm)
  • 2 x Grip Head

Note: The monolight shown in some promotional images is not included.

Setup Instructions

Follow these steps to assemble your NEEWER C Stand:

  1. Unfold the Legs: Carefully rotate the stand legs outwards until they are fully extended and in the proper position for stability.
  2. Secure the Legs: Tighten the screws located at the base of the stand to firmly secure the legs in their open position. Ensure all legs are locked to prevent accidental collapse.
  3. Attach Grip Heads: Slide the grip heads onto the main column and the boom arm. Tighten the handles on the grip heads to secure them in your desired position.
  4. Insert Boom Arm: Insert the boom arm into one of the grip heads. Adjust its position and angle as needed, then tighten the grip head handle to lock it in place.
Step-by-step instructions for setting up the C-stand legs.
Visual guide for rotating and securing the C-stand legs.

Operating the C Stand

Height Adjustment

The 3-section center column allows for flexible height adjustments. Loosen the locking knobs on each section, extend the column to your desired height, and then securely tighten the knobs. The stand features an inner buffer spring to reduce impact from sudden drops, but always ensure a firm grip when adjusting height with equipment attached.

C-stand height adjustment range from minimum to maximum.
The C-stand can be adjusted from a minimum height of 58.6 inches (149 cm) to a maximum of 121.6 inches (309 cm). The boom arm is 47 inches (120 cm) long.

Flexible Sliding Legs

The uppermost leg of the C stand is designed to slide up or down. This feature allows the stand to adapt to complex and uneven shooting surfaces, such as stairs or sloped ground, providing enhanced stability where traditional stands might fail. Non-slip rubber pads on the feet further improve stability and protect surfaces.

Comparison of upgraded C-stand stability on uneven ground versus a standard light stand.
This image illustrates the stability of the upgraded C-stand on stairs and uneven surfaces, contrasting it with a conventional light stand that cannot maintain stability in similar conditions.
Diagram showing the flexible leg feature of the C-stand and its key attributes.
The diagram highlights the flexible leg design, allowing the uppermost leg to slide for adaptation to complex shooting environments. Key features listed are Stable Structure, Adjustable Height, Universal Adapter, and Stainless Steel Construction.

Using the Boom Arm and Grip Heads

The 3.9 ft (120 cm) extension arm is equipped with 1/4" and 3/8" mounting screws, offering broad compatibility with various photographic equipment. The two metal grip heads are designed to securely lock the extension arm and allow for flexible angle adjustments. Each grip head features four holes with multiple bore diameters (15mm, 11mm, 7mm, 4mm) to accommodate different rods, arms, flags, and umbrella shafts.

Detailed view of the sturdy grip head with multiple bore diameters and locking mechanism.
This image displays the grip head, showing its multiple bore diameters (15mm, 11mm, 7mm, 4mm) suitable for various poles, and illustrates the fixed and movable handle heads for secure locking.

Applications

The NEEWER C Stand is suitable for a wide range of applications, including:

  • Photography
  • Video Creation
  • Outdoor Shooting
Examples of the C-stand in various photography and video applications.
This image demonstrates the wide application of the C-stand in photography, video creation, and outdoor shooting scenarios, supporting lights and modifiers.

Maintenance

  • Cleaning: Wipe down the stainless steel surfaces with a soft, damp cloth to remove dust and dirt. For stubborn grime, a mild detergent can be used, followed by thorough drying to prevent water spots.
  • Lubrication: Periodically apply a small amount of silicone-based lubricant to the moving parts, such as the sliding leg mechanism and locking knobs, to ensure smooth operation.
  • Inspection: Regularly check all screws, knobs, and joints for tightness. Tighten any loose components to maintain stability and safety.
  • Storage: When not in use, collapse the C Stand and store it in a dry, clean environment to prevent corrosion and damage.

Troubleshooting

  • Stand feels unstable: Ensure all leg screws are fully tightened and the legs are spread to their maximum extent. If on uneven ground, utilize the flexible sliding leg feature to balance the stand.
  • Boom arm slips: Verify that the grip head handles are securely tightened. Ensure the boom arm is correctly seated within the grip head's bore.
  • Difficulty adjusting height: Check if the locking knobs are fully loosened. If movement is stiff, apply a small amount of lubricant to the inner column sections.
  • Scratches on floor: Ensure the non-slip rubber pads on the feet are intact. Replace if worn or missing.

Specifications

FeatureDetail
Brand NameNEEWER
Model Number10093452
Material100% Stainless Steel
Maximum Height121.6 inches / 309 centimeters
Minimum Height58.6 inches / 149 centimeters
Boom Arm Length47 inches / 120 centimeters
Maximum Load (Stand)44 lb / 20 kg
Maximum Load (Boom Arm)17.6 lb / 8 kg
Grip Head Bore Diameters15mm, 11mm, 7mm, 4mm
Boom Arm Mounting Screws1/4" and 3/8"
ColorSilver
OriginMainland China

User Tips

  • Always use sandbags or counterweights on the boom arm when extending it with heavy equipment to prevent tipping.
  • When adjusting the height, especially with gear mounted, hold the equipment firmly to prevent sudden drops, even with the internal buffer spring.
  • Take advantage of the sliding legs on uneven terrain to ensure a perfectly level and stable setup for your lighting.
  • Before each use, quickly check all locking mechanisms to ensure they are secure.

Warranty and Support

For warranty information, technical support, or service inquiries, please refer to the official NEEWER website or contact your authorized dealer. Keep your purchase receipt as proof of purchase for any warranty claims.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.