1. Introduction
1.1. Preface
To help you ward off bodily injury or property loss that may arise from improper operation, please read all the information carefully before using our products.
1.2. Intended Use
Our products are designed to provide reliable wireless communication services for users across many industry sectors. In order to use the products safely and to achieve the best performance, they must be used as intended. The operator of the product is responsible for damage to the product or damage caused by the product if the product was used beyond the intended use instructions.
Intended use includes that:
- The product is used by users who have full knowledge of its RF exposure and can exercise control over their RF exposure to meet the occupational limits in FCC/ICNIRP and international standards.
- All the security instructions set forth in this document are always heeded.
- The general, national and in-house safety regulations are heeded.
- The product is exclusively used with the frequencies licensed by the respective authority.
- The product is configured appropriately by the dealer.
Besides, intended use also requires the product operator to be well-trained and to be familiar with the applicable standards, regulations and commissions.
1.3. Package Contents
The standard package for the BD-V12B includes the following items. If any item is missing, please verify with your dealer.
- 1 × Radio
- 1 × Li-Ion battery pack (1500mAh)
- 1 × Wrist strap
- 1 × Belt clip
- 1 × Owner's Manual
- 1 × Adapter (with Type-C cable)
- Optional: Headset, Multi-unit charger, programming cable
2. Safety Information and Regulations
2.1. RF Radiation Information
Compliance with RF Exposure Standards: The radio complies with the following RF energy exposure standards and guidelines:
- United States Federal Communications Commission, Code of Federal Regulations; 47 CFR 1.1307, 1.1310 and 2.1093
- American National Standards Institute (ANSI) / Institute of Electrical and Electronic Engineers (IEEE) C95.1:2005; Canada RSS102 Issue 5 March 2015
- Institute of Electrical and Electronic Engineers (IEEE) C95.1:2005 Edition
2.2. RF Exposure Compliance and Control Guidelines and Operating Instructions
To control your exposure and ensure compliance with the occupational/controlled environmental exposure limits, always adhere to the following procedures.
Guidelines:
- Do not remove the RF Exposure Label from the device.
- User awareness instructions should accompany device when transferred to other users.
- Do not use this device if the operational requirements described herein are not met.
Operating Instructions:
- Transmit no more than the rated duty factor of 50% of the time. To transmit (talk), press the Push-to-Talk (PTT) key. To receive calls, release the PTT key. Transmitting 50% of the time, or less, is important because the radio generates measurable RF energy only when transmitting (in terms of measuring for standards compliance).
- Keep the radio unit at least 2.5 cm away from the face. Keeping the radio at the proper distance is important as RF exposure decreases with distance from the antenna. The antenna should be kept away from the face and eyes.
- When worn on the body, always place the radio in an approved holder, holster, case, or body harness or by use of the correct clip for this product. Use of non-approved accessories may result in exposure levels which exceed the FCC's occupational/controlled environmental RF exposure limits.
- Use of non-approved antennas, batteries, and accessories causes the radio to exceed the FCC RF exposure guidelines.
- Contact your local dealer for the product's optional accessories.
- Do not operate the product near any medical or electronic equipment that is vulnerable to RF signals.
- Do not hold the product while driving.
- Do not operate the product in any area where use of wireless communication equipment is completely prohibited.
2.3. FCC Regulations
Federal Communication Commission (FCC) requires that all radio communication products should meet the requirements set forth in the above standards before they can be marketed in the U.S, and the manufacturer shall post a RF label on the product to inform users of operational instructions, so as to enhance their occupational health against exposure to RF energy.
FCC Statement: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. Verification of harmful interference by this equipment to radio or television reception can be determined by turning it off and then on. The user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a different circuit to that of the receiver's outlet.
- Consult the dealer or an experienced radio/TV technician for help.
Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including that may cause undesired operation.
Note: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
FCC Part 15.21 Warning Statement: NOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE. SUCH MODIFICATIONS COULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT.
2.4. IC Statement (Industry Canada)
The device has been tested and complies with SAR limits, users can obtain Canadian information on RF exposure and compliance. After examining this equipment for compliance with DAS limits and/or RF field intensity limits, users can on exposure to radio frequencies and the conformity and compliance of obtaining the corresponding information. This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
This device complies with the Canadian Industry Canada regulations applicable to license-exempt radio devices. L'exploitation est autorisée under the following two conditions: (1) The device must not cause any interference, and (2) The user of the device must accept any interference. Electromagnetic interference, even if the interference is likely to compromise its operation.
2.5. EU Regulatory Compliance
As certified by the qualified laboratory, the product is in compliance with the essential requirements and other relevant provisions of the Directive 2014/53/EU. All applicable EU regulations are regarded (2006/66/EC, 2011/65/EU, 2012/19/EU). Please note that the above information is applicable to EU countries only.
2.6. Precautions for Portable eTerminals
Operating Prohibitions: To protect you against any property loss, bodily injury or even death, be sure to observe the following safety instructions:
- Do not operate the product in a location containing fuels, chemicals, explosive atmospheres and other flammable or explosive materials. In such location, only an approved Ex-protection model is allowed for use, but any attempt to assemble or disassemble it is strictly prohibited.
- Do not operate the product near or in any blasting area.
Important Tips: To help you make better use of the product, be sure to observe the following instructions:
- Do not use any unauthorized or damaged accessory.
- Keep the product at least 2.5 centimeters away from your body during transmission.
- Do not keep the product receiving at high volume for a long time.
- For vehicles with an air bag, do not place the product in the area over the air bag or in the air bag deployment area.
- Keep the product and its accessories out of reach of children and pets.
- Please operate the product within the specified temperature range.
- Continuous transmission for a long time may lead to heat accumulation within the product. In this case, please keep it at a proper location for cooling.
- Handle the product with care.
- Do not disassemble, modify or repair the product and its accessories without authorization.
Protect your hearing:
- When using the radio without a headset or earpiece, do not place the radio's speaker directly against your ear.
- Use the lowest volume necessary to do your job.
- Turn up the volume only if you are in noisy surroundings.
- Turn down the volume before adding headset or earpiece.
- Limit the amount of time you use headsets or earpieces at high volume.
- Use careful with the earphone, as possible excessive sound pressure from earphones and headphones can cause hearing loss.
3. Main Controls and Parts of the Radio
The Baofeng BD-V12B features a compact design with essential controls for easy operation:
- Antenna: For transmitting and receiving signals.
- Power/Volume Knob (Encoder): Rotate clockwise to turn on and increase volume; counter-clockwise to decrease volume and turn off.
- LED Indicator: Displays radio status (Red: Transmitting, Green: Receiving, Flashes Green: Analog Scan, Flashes Yellow: Encryption Scan).
- PTT Key (Push-to-Talk): Press and hold to transmit; release to receive.
- SK-Monitor Key (Programmed Key): Can be programmed for functions like Monitor, High/Low Power, or Emergency Alarm.
- Speaker: For audio output.
- Microphone: For voice input.
- Speaker/Mic Jack: For connecting external audio accessories.
- Battery Pack: Removable and rechargeable.
- Battery Release Latch: To remove the battery pack.
- Type-C Port: Located at the bottom of the battery for charging.
4. Setup
4.1. Battery Recharge
To charge the battery in your radio:
- Insert the random original adapter into an AC socket, and then insert the adapter cable into the Type-C socket at the bottom of the battery (open the protective cover).
- Ensure that the Type-C socket at the bottom of the battery is in good contact with the charging terminal of the cable. The charging indicator light at the bottom of the battery turns red and charging begins.
- It takes approximately 2-5 hours to fully charge the battery. The charging indicator light at the bottom of the battery is off when charging is complete.
When the charging indicator light at the bottom of the battery goes off, it indicates that the charging is complete. Remove the cable from the Type-C port at the bottom of the battery and cover the interface protection cover.
Baofeng recommends your radio is turned off while being charged.
5. Operation
5.1. Power On/Off and Volume Adjustment
- To turn on: Rotate the [Power/Volume] knob clockwise until you hear a mechanical "click". If voice prompts are enabled, you will hear "Power on and channel number".
- To adjust volume: Continue rotating the [Power/Volume] knob clockwise to increase volume, or counter-clockwise to decrease volume.
- To turn off: Rotate the [Power/Volume] knob counter-clockwise until you hear a mechanical "click".
5.2. Channel Selection
The radios can store up to 16 channels, and the channel type allows programming to analog or/and encrypted. In standby mode, turn the channel knob to select the channel you want. When the voice prompt function is enabled, the corresponding channel is broadcasted by voice.
- If the channel is encrypted, it will be accompanied by "Encryption and channel number".
- Attention: It is necessary to set the members of the group on the same channel in order to communicate through radios.
5.3. Making a Call
To communicate, all radios in your group must be set to the same channel. Briefly press the [SK1] (Monitor key) to enable the Monitor feature in order to make sure that the frequency is not busy, and then press the [PTT] key. Release the [PTT] key to receive. Only one user at a time can talk during radio communications. Therefore, it is important not to transmit when you are receiving a communication and use the transmission mode sparingly to allow other users to talk. Transmission consumes a significant amount of energy and should therefore be used sparingly to prolong the battery life. If you are unable to contact a station that you have no problems in receiving, the station may be using CTCSS tones or DCS codes.
5.4. Making an Encryption Call
Select an encryption channel, press and hold the [PTT] key. The radio will be in the transmitting state, and the red indicator light will be constantly on. Then speak in a normal tone into the microphone. After releasing the [PTT] key, the yellow light briefly flashes once, and the radio is in an acceptable state. When receiving a call, the yellow indicator light remains on.
Note: Set the group members on the same channel and encryption sequence (0-31) to achieve interconnection.
5.5. Monitor Function
Before using the monitor function, check whether it is an analog channel. The monitor function is only available for analog channels. In standby mode, press and hold [SK1] (Monitor key) to turn on the monitor function. Release [SK1] (Monitor key) to exit the monitor state.
On analog channels, you can use [SK1] (Monitor key) to hear weaker signals that are difficult to hear during normal operation, and to adjust the volume when there is no signal on the channel you have selected.
5.6. Channel Scan
This function can be activated only by means of the optional programming software. Program at least two scanning channels for the radio before using the scanning function.
Analog Scanning:
- Press and hold the [PTT] + [SK1] key on the 16th channel to turn on the radio and enter the analog scan. The scan starts from the current channel, and the signal light is flashing "green". Press the [SK1] key again to exit the scan.
- The green light illuminates when scanning pauses on a channel.
- At any time during scanning, simply press the [SK1] key to pause the radio scanning. The radio returns to the channel of the last received signal for transmission. If no valid signal is received during the scanning period, then return to the scanning start channel for transmission.
- Scanning method: In carrier scanning mode, scanning stops when a signal is detected, and scanning continues after 5 seconds of carrier signal loss. After scanning the signal, the voice prompts the channel number scanned.
Encryption Scanning:
- Press and hold the [PTT] + [SK1] key on the 14th channel to turn on the radio and enter the encryption scan. The scan starts from the current channel, and the signal light is flashing yellow. Press the [SK1] key again to exit the scan.
- When scanning pauses on a channel, the yellow light will light up.
- At any time during scanning, simply press the [SK1] key to pause the radio scanning. The radio returns to the channel of the last received signal for transmission. If a valid signal is continuously received during the scanning period, it will return to the scanning start channel for transmission.
- Scanning method: In carrier scanning mode, scanning stops when a signal is detected, and scanning continues after 5 seconds of carrier signal loss. After scanning the signal, the voice prompts the channel number scanned.
5.7. Prompt Voice Switch Settings
Select the 10th channel using the encoder. Press and hold the [PTT] + [SK1] to turn on the radio, and turn the prompt voice on or off. If the prompt voice function is on, there will be voice prompts when the encoder is turned on or operated. If you turn off the prompt voice function, there is only a "beep" prompt when you turn on or operate the encoder.
5.8. VOX (Voice Operated Exchange)
The VOX feature enables hands-free conversations without using the PTT button. Just speak in the direction of the microphone and the communication will be automatically activated. The VOX sensitivity can be adjusted in 5 different levels (1-5) through the programming software. Level 2 is set by default and has the lowest VOX sensitivity, while 5 is the highest.
With the programming software, you can enable/disable the VOX feature and select the sensitivity levels.
Note: In channel 5, press and hold the [PTT] + [SK1] keys to turn on the radio and prompt "VOX on, welcome 5" to turn on/off voice control.
5.9. Frequency Sweep Function
Rotate the channel knob to Channel 1, press and hold the [PTT] + [SK1] key to turn on the radio. The voice will announce "Power On" to enter the sweep function and the green light will flash; Press the [SK1] key to prompt a "beep" sound and the green light remains on, and start scanning. After scanning, it will be automatically stored and prompted with two beeps. (The green light remains on during scanning, and the green light flashes when scanning is stopped)
Rotate to channel 2, press the [SK1] key to continue scanning. After scanning, it will be automatically stored and prompted with a "beep" sound, with the indicator light as described above;
Rotate to channel 3 and press the [SK1] key to continue scanning. After scanning, it will be automatically stored and prompted with a "beep" sound; Operate in sequence until channel 16.
Complete the frequency sweep task, shut down and restart to exit the frequency sweep mode, and the frequency sweep task ends.
5.10. Quick Group Formation (Wireless Clone Function)
Rotate the channel knob to channel 2, press and hold the [PTT] + [SK1] key to turn on both the transmitter and receiver. The receiver and transmitter prompt "beep" to enter wireless replication. When the transmitter presses the [PTT] key, the red light remains on, and the receiver green light automatically remains on. Copy all the configuration parameters of channels 1-16 of the transmitter, and the receiver prompts "beep" twice to complete the replication. Both prompt lights turn off and automatically restart, the replication task has ended.
5.11. Voice Frequency Hopping
Set frequency hopping on/off for each channel through CPS software. When the frequency hopping function is enabled, it cannot communicate with the regular settings.
5.12. CTCSS/DCS Tones
CTCSS and DCS tones are similar to access codes and enable the radio to communicate only with the users that are tuned on the same channel and have set the same code. For each channel, you can set up to 51 CTCSS tones and 210 DCS codes. The CTCSS/DCS tones are a sort of "access codes" and enable the radio to communicate only with the other users set on the same frequency and on the same CTCSS/DCS tone.
Note: Channels with frequency hopping function must be synchronously set with CTCSS or DCS.
5.13. Quick Operation Radio (Without CPS Programming Software)
You can perform the following quick operations through the combination of [PTT] + [SK1]:
- On the 1st channel, press and hold the [PTT] + [SK1] to turn on the radios, and the green light flashes to perform frequency scanning.
- On the 2nd channel, press and hold the [PTT] + [SK1] to open the radios, which can be wirelessly copied to quickly group up.
- On the 5th channel, press and hold the [PTT] + [SK1] to turn on the radio and turn the VOX function on or off. Accompanied by a voice prompt VOX On or VOX Off.
- On the 10th channel, press and hold the [PTT] + [SK1] to turn on the radio and turn on or off the prompt voice function.
- On the 15th channel, press and hold the [PTT] + [SK1] to turn on the radio and switch the prompt language between Chinese and English.
- On the 16th channel, press and hold the [PTT] + [SK1] to turn on the radio and turn on or off the analog channel scanning function.
- On the 14th channel, press and hold the [PTT] + [SK1] to turn on the radio and turn on or off the encrypted channel scanning function.
6. Maintenance
6.1. Battery Maintenance Instructions
To help your battery work normally or prolong its life, be sure to observe the following instructions:
- Accumulated dust on charging connector may affect normal charging. Please use a clean and dry cloth to wipe it on a regular basis.
- It is recommended to charge the battery under 5°C~40°C. Violation of the said limit may cause battery life reduction or even battery leakage.
- To charge a battery attached to the product, turn it off to ensure a full charge.
- Do not remove the battery or unplug the power cord during charging to ensure a smooth charging process.
- Do not dispose of the battery in fire.
- Do not expose the battery to direct sunlight for a long time nor place it close to other heating sources.
- Do not squeeze and penetrate the battery, nor remove its housing.
- Do not charge your battery suffering deformation, leakage and overheat.
- Do not charge your battery with an unauthorized charger.
- Do not charge your battery in a location where strong radiation is present.
- Overcharge shall always be prohibited for it may shorten the life of your battery.
6.2. Transportation Instructions
- Damaged batteries must not be transported.
- To avoid short circuit, separate the battery from metal parts or from each other if two or more batteries are transported in one packaging.
- The radio must be switched off and secured against switch-on, if the battery is attached.
The content of the shipment must be declared in the shipping documents and by a Battery Shipping Label on the packaging. Contact your hauler for the local regulations and further information.
6.3. Precautions for Disposal
Once the service life of our products (including but not limited to radios and batteries) has ended, they shall not be disposed as household garbage. Their recycling and disposal shall satisfy your local regulations.
7. Troubleshooting Guide
| Problem | Solution |
|---|---|
| The radio doesn't switch on | The battery may be exhausted. Recharge it. Uncorrected installation. |
| Battery recharge doesn't last long | The battery pack is old. Change it with a new one. Battery pack is not completely charged. |
| Reception LED turns on but no sound heard | Make sure the volume is not too low. Make sure to have the same CTCSS and DCS codes of your group. |
| The keypad doesn't work | Keypad lock function hasn't been enabled. |
| Reception of other group signal while transmitting | Change another CTCSS/DCS for your group. |
Note: If the above solutions cannot fix your problems, or you may have other queries, please contact your dealer for more technical support.
8. Technical Specifications
| General | |
|---|---|
| Frequency range | 400~480 MHz* |
| Working temperature | -10/+60°C |
| Operating voltage | 3.7V |
| Operate mode | Simplex |
| Dimensions | 164*60*32.5 mm (with antenna) |
| Weight | 160 g (Battery pack included) |
| Antenna Impedance | 50Ω |
| Transmitter | |
| Frequency stability | ±2.5PPM |
| Output power | <2WERP (0.5W-3W) |
| Max frequency deviation | ≤2.5KHz |
| Audio distortion | ≤3% |
| Adjacent channel power | < 60 dB |
| Receiver | |
| RF sensibility | <0.2UV@20 dB SINAD |
| Audio distortion | ≤3% |
| Audio response | 300Hz+3KHz |
| Adjacent channel selectivity | Within European legal terms |
WARNING: Direct plug-in ac/dc power supply must be used for disconnecting the transceiver from the mains; the desktop charger must be positioned close to the unit and easily accessible.
NOTE: The frequency range is the hardware design frequency, and the actual frequency that can be used must be strictly in accordance with the regulatory requirements of the country and region where it is used.
9. User Tips
- For optimal range, ensure the antenna is securely attached and unobstructed during use.
- Utilize the intelligent noise reduction feature in loud environments for clearer communication.
- Take advantage of the wireless cloning function to quickly set up multiple radios with the same channel configurations.
- When using the Type-C charging, any standard USB power source (like a phone charger or power bank) can be used for convenience.
- Regularly check the battery level and recharge as needed to avoid interruptions during critical communications.
- Explore the programmable SK-Monitor key to customize a frequently used function for quick access.
10. Warranty and Support
10.1. Disclaimer
The Company endeavors to achieve the accuracy and completeness of this manual, but no warranty of accuracy or reliability is given. All the specifications and designs are subject to change without notice due to continuous technological development. No part of this manual may be copied, modified, translated, or distributed in any manner without the prior written consent of the Company. We do not guarantee, for any particular purpose, the accuracy, validity, timeliness, legitimacy or completeness of the third-party products and contents involved in this manual.
10.2. Contact Information
Fujian Baofeng Electronics Co., Ltd.
Address: Changfu Industrial Zone Xiamei, Nan'an, Quanzhou, Fujian, China
E-mail: wangjianhui@baofengradio.com
Website: http://www.baofengradio.com
Print version: BF-V12D_V1.0
For further assistance or to view the full item guides and documents, please refer to the official user manual PDF: User manual (PDF)