1. Introduction
Thank you for purchasing the HamGeek RK-ZYNQ7020-F ZYNQ7020 Development Board. This manual provides essential information for the safe and effective use of your development board. It covers basic product information, safety warnings, operational instructions, technical specifications, maintenance, and troubleshooting.
The RK-ZYNQ7020-F development board utilizes Zynq7000 series chips, specifically the XC7Z020CLG484-2 model. The ZYNQ7020 chip integrates both a Processor System (PS) and Programmable Logic (PL) for versatile applications.
This board features a comprehensive design with a rich array of peripheral interfaces, including DDR3, EMMC, QSPI, onboard JTAG+UART integration, SD card, USB2.0 HOST/SLAVE, PS Gigabit Ethernet, PL Gigabit Ethernet, RS485x2, FMC(LPC), CANx2, HDMI-compatible, MIPI, EEPROM, RTC, SPILCD, 40PIN IO, PS LED KEY, and PL LED KEY.
For detailed technical specifications, specific manuals, or software for this model, please contact customer support.
2. Package Contents
Upon opening the package, please verify that all the following items are included:
- 1 x RK-ZYNQ7020-F Development Board
- 1 x 12V 3A Power Adapter
- 1 x Card Reader
- 1 x 32G SD Card
- 1 x Type-C Cable

3. Safety Warnings
Before using this product, please read and comply with all safety instructions to prevent damage or injury.
3.1 Electrical Safety
- Use only the power adapter provided with the product or a compliant power supply (12V 3A).
- If the power cord is damaged, discontinue use immediately and contact customer support for a replacement.
- Always disconnect the power before cleaning the device.
3.2 Usage Environment
- Operating temperature range: -10°C to 40°C.
- Avoid direct sunlight, high temperatures, and dusty environments.
- Keep ventilation good and do not block heat dissipation holes.
- Do not use in humid environments unless the product specifically states a waterproof rating (this product has an IP20 rating for indoor use, meaning it is not waterproof).
3.3 Operational Safety
- Do not disassemble or modify the product yourself, as there are no user-repairable parts inside.
- Prevent liquid from entering the product interior.
- If the product emits smoke, unusual odors, or abnormal noise, immediately disconnect the power and contact customer support.
4. Product Overview: Components and Interfaces
The RK-ZYNQ7020-F development board is designed with a comprehensive set of components and interfaces to support various FPGA and embedded system development tasks. Below is a detailed diagram identifying the key features.

Key Components and Interfaces:
- **ZYNQ XC7Z020-CLG484-2 Chip**: The core processing unit, integrating PS and PL.
- **DDR3 1GB**: High-speed memory for the Processor System.
- **EMMC 8GB**: Embedded MultiMediaCard for storage.
- **QSPI 256MB**: Quad SPI Flash for configuration and data storage.
- **SD Card Slot**: For external storage and boot options.
- **USB HOST/SLAVE**: USB 2.0 interface for connecting peripherals or acting as a device.
- **PS Gigabit Ethernet**: Ethernet port connected to the Processor System.
- **PL Gigabit Ethernet**: Ethernet port connected to the Programmable Logic.
- **RS485 x2**: Two RS485 interfaces for industrial communication.
- **CAN x2**: Two CAN bus interfaces for automotive and industrial applications.
- **FMC-LPC (Low Pin Count)**: Flexible Mezzanine Card connector for expansion.
- **HDMI OUT**: HDMI output for display.
- **MIPI**: Mobile Industry Processor Interface for camera or display.
- **EEPROM 256KB**: Electrically Erasable Programmable Read-Only Memory.
- **RTC (Real-Time Clock) with Battery**: For timekeeping functions.
- **SPILCD 1.47" 320x172**: Small SPI LCD display.
- **40PIN IO**: General-purpose input/output pins.
- **JTAG UART**: Debugging and programming interface.
- **POW LED**: Power indicator LED.
- **RST KEY**: Reset button.
- **PS LED KEY**: Processor System LEDs and Keys.
- **PL LED KEY**: Programmable Logic LEDs and Keys.
- **DIP Switch**: For boot mode selection and other configurations.
- **FPGA DONE indicator**: LED indicating FPGA configuration completion.
- **12V Power Input**: Power supply connector.

Pinout and Voltage Settings (Bottom View):
The bottom side of the board provides detailed pinout information and adjustable voltage settings for specific interfaces. Refer to Figure 4.2 for the physical layout.
| Setting | Voltage (V) | Description |
|---|---|---|
| 8A | DEFAULT | Default setting |
| 6.0K | 1.8V | ADJ1/RA1: 2.5V/4.7K (FMC) |
| 4.7K | 2.5V | ADJ2/RA2: 3.3V/3.24K (40P IO) |
| 3.24K | 3.3V |
5. General Operating Instructions
5.1 First Use
- Ensure the product is fully charged before use (if applicable, though this is a development board, ensure stable power).
- Check if the power supply voltage is consistent with the product specifications (AC100-240V, 50/60Hz, applicable worldwide for the adapter; the board requires 12V DC input).
5.2 Basic Operations
- **Power On/Off**: Press and hold the power button for 3 seconds to turn the board on or off.
- **Function Selection**: Short press the mode button to switch functions (if available and configured).
- **Display Screen**: The onboard 1.47" LCD (320x172) can display current values or status, depending on the programmed application.
6. Instrument-Specific Instructions (General Guidance)
While the RK-ZYNQ7020-F is a development board, if it is used in applications that fall under the category of instruments and meters (e.g., testing instruments), please consider the following additional information:
6.1 Measurement Safety Level
- Confirm the product's corresponding measurement category (CAT I/II/III/IV) and rated voltage for your specific application. Do not use it outside the specified range.
- When measuring an unknown voltage, always start with the highest range.
6.2 Calibration and Maintenance
- It is recommended to calibrate annually to ensure measurement accuracy for precision applications.
- For calibration services, please contact a professional organization or customer support.
6.3 Applicable Standards (for reference)
This product series is designed with reference to the following standards:
- Electrical safety: EN 61010-1
- Electromagnetic compatibility: EN 61326-1
- Specific requirements are subject to the conformity declaration corresponding to the model number.
7. Technical Specifications
Below are the general technical specifications for the RK-ZYNQ7020-F Development Board. Please refer to the product label for specific details if variations exist.
| Parameter Category | General Scope | Remark |
|---|---|---|
| Input power | AC100-240V, 50/60Hz or DC5V/9V/12V | Please refer to the product label. The board itself requires 12V DC. |
| Operating temperature | -10℃ ~ 40℃ | |
| Storage temperature | -20℃ ~ 60℃ | |
| Protection level | IP20 (for indoor use) | Except for waterproof models |
| Authentication information | CE, RoHS | Compliant with EU directives |
Physical Dimensions and Weight:
- **Length**: 15 cm
- **Width**: 14 cm
- **Height**: 10 cm
- **Weight**: 0.5 kg

8. Maintenance and Care
- **Cleaning**: Wipe the outer casing with a soft, dry cloth. Do not use chemical solvents.
- **Storage**: When not in use for an extended period, clean the board and store it in a cool, dry place.
- **Battery (if applicable)**: If the board contains a removable battery (e.g., for RTC), and it will not be used for an extended period, please remove the battery to prevent leakage.
9. Troubleshooting Common Problems
If you encounter issues with your development board, refer to the table below for common problems and their solutions.
| Problem | Possible Reasons | Solution |
|---|---|---|
| Unable to power on | Power not connected/battery depleted | Check the power connection, ensure the adapter is correctly plugged in, and try again. |
| No display/Display error | Poor connection/Incorrect settings | Restart the device and check all connections, especially to the display. Verify DIP switch settings for boot mode. |
| Inaccurate measurement values (instrument-related) | Range error/calibration required | Confirm the measurement range and contact calibration services if necessary. |
| Other faults | Contact customer service for technical support. |
10. EU Compliance Information
10.1 CE Declaration of Conformity
This product complies with the essential requirements of the following EU directives:
- Low Voltage Directive (LVD) 2014/35/EU
- Electromagnetic Compatibility Directive (EMC) 2014/30/EU
- RoHS Directive 2011/65/EU
10.2 Waste Electrical and Electronic Equipment (WEEE)
The wheeled bin symbol marked with an X on the product indicates that, according to EU Directive 2012/19/EU, this product must not be disposed of as unsorted municipal waste. It must be collected and recycled separately to prevent potential harm to the environment and human health from uncontrolled waste disposal.
11. Warranty and Support
Warranty Policy
The product comes with a 12/24 months warranty from the date of purchase. Please refer to store announcements for the exact duration applicable to your purchase.
Technical Support
For detailed technical documentation, calibration certificates, or hard copies of the manual, please contact customer support via email at hamgeeks@163.COM. Responses are typically provided within 24 working hours.
Alternatively, you can contact the EU Responsible Person for compliance-related inquiries:
- **Name**: Apex CE Specialists GmbH
- **Address**: Habichtweg 1, 41468 Neuss, Germany
- **Phone Number**: +35321-2066339
- **Email**: Info@apex-ce.com
The user manual is also available as a PDF document: View User Manual (PDF).
12. Disclaimer
This instruction manual is a general version. The actual product functions and parameters shall prevail. The manufacturer reserves the right to change product designs and specifications without prior notice.