Heltecbms 18650/21700 Battery Storage Case

Contents

Heltecbms 18650/21700 Battery Storage Case Instruction Manual

Model: HT-B18650P, HT-B21700P Series

1. Safety & Warnings

Read all instructions before use to ensure safety and prevent damage.

  • Warning: Keep the device and its cord out of reach of children under 3 years old.
  • Always ensure correct battery polarity when inserting cells.
  • Do not short-circuit the battery holder.
  • Use appropriate protective boards for series/parallel configurations to prevent overcharging or overdischarging.

2. Product Overview

The Heltecbms battery storage cases are designed for DIY assembly of 18650 and 21700 lithium-ion battery packs. They come in regular and enhanced versions, offering flexibility for various applications.

Comparison of Regular and Enhanced Battery Holders
Figure 2.1: The difference between regular and enhanced versions of the battery holders. Enhanced versions feature springs for better current handling.
Nickel-plated spring clips detail
Figure 2.2: Detail of nickel-plated spring clips. Regular models have no spring under the shrapnel (manganese steel plated with nickel), while enhanced versions have springs (nickel-plated copper) capable of carrying large currents.
Stretching design to prevent deformation
Figure 2.3: Stretching design to effectively secure the battery and reduce the risk of holder deformation.

3. Setup and Installation

3.1 Basic Battery Insertion

  1. Put lithium cells into the slots of the plastic battery holder one by one.
  2. Assemble multiple holders to form your needed series-parallel battery layout.

3.2 DIY Assembly with PCB Boards

These battery holders are designed as components suitable for use with PCB boards, offering a high degree of freedom for DIY projects. You can choose from 1-string, 2-string, 3-string, or 4-string battery slots, all compatible with a PCB board (PCB board needs to be prepared by yourself).

DIY assembly with PCB board
Figure 3.1: Illustration of plug-in battery compartments on a PCB board for easy installation.

3.3 Splicing Multiple Holders

The battery holders feature a concave and convex design for unlimited splicing, allowing for flexible configurations.

Concave and convex design for splicing
Figure 3.2: The connection is simple, tight, and firmly fixed on both sides using the concave and convex design.

Splicing Method:

Align the side shell with the one with the groove up and down, and then push the groove into the groove from top to bottom with force. The holders support both vertical and horizontal splicing.

Splicing type battery slot
Figure 3.3: Different splicing type battery slots available (18650/21700/5AA/7AAA).

3.4 Connecting Positive and Negative Terminals

To avoid short circuiting, always insert the battery positive terminal into the spring end first, and then insert the entire battery into the box. To remove the battery, take it out from the nut end.

Positive and Negative Battery Slots
Figure 3.4: Illustration of the positive (spring end) and negative (nut end) connections. Components for connection include M3x16MM screws, M3 nuts, square terminal posts, and wire nuts.

Splicing Standard List (for welding/stitching):

  • Battery box *1
  • M3x16mm (full-threaded screw) *1
  • M3x16mm (semi-threaded screw) *1
  • M3 brass square columns *2
  • M3 brass nuts *3
  • 10mm spring (spring steel zinc-coated) *1
  • M3 wire nose *2
  • Transparent top cover *1 (optional)
  • Transparent side cover *2 (optional)

4. Operating Instructions

4.1 Series and Parallel Connections

When assembling, carefully read the instructions to correctly connect in series or in parallel.

  • Parallel Demand: Optional 2/3/4 slots for battery specifications.
  • Series Demand: The connection must be made using the "single section slot" option. In a high-current environment, the series connection must achieve complete physical isolation insulation through a single section of the slot. It is strictly prohibited to make any changes to the series connection within the multi-section parallel slots.
Series/Parallel connection specification
Figure 4.1: Visual representation of series/parallel connection considerations.

4.2 Current Handling and Output Voltage

Both 18650 and 21700 battery cells can sustain a continuous current of 3-5A in regular holders. Enhanced versions can handle a higher current of 24-35A.

Continuous and stable current
Figure 4.2: Illustration of continuous current capabilities for regular and enhanced versions.

For 3-Cell Series Battery Box:

  • Output Voltage: 11.1 - 12.6V.
  • Maximum Output Current: 3-5A.

For 3-Cell Parallel Battery Box:

  • Output Voltage: 3.7 - 4.2V.
  • Maximum Output Current: 3-5A.

The positive and negative electrode collection lines are suitable for discharging of 1-3A. If a discharge of 5A is required, please replace the lines yourself.

Current carrying capacity for flat-head batteries
Figure 4.3: The holders are suitable for flat-head 18650/21700 batteries and can carry a current of 5-10A.

5. Maintenance

The battery holders are constructed from environmentally friendly ABS thickened material, providing high strength and good texture. The nickel-plated springs are designed for durability and rust prevention.

  • Keep the battery holders clean and free from dust and debris.
  • Avoid exposing the holders to extreme temperatures or moisture.
  • Periodically check the spring contacts for any signs of corrosion or deformation.

6. Troubleshooting

  • Battery Damage (Overcharging/Overdischarging): A protective board must be installed at the load end. Without it, batteries may be damaged.
  • Poor Contact / Soft Spring: Excessive current (above 3-5A for standard versions) may cause the spring to become soft, leading to poor contact. Ensure current limits are respected or use enhanced versions for higher currents.
  • Short Circuiting: Always insert the battery positive terminal into the spring end first.
  • Deformation: The stretching design helps prevent deformation, but avoid excessive force or improper handling.

7. Specifications

7.1 General Product Features

  • Material: Environmentally friendly ABS (thickened), PC + ABS (black), PC (covers).
  • Conductive Material: 18650/21700: Brass; 5AA/7AAA: Iron plated with nickel.
  • Springs: Nickel-plated, strong elasticity, rust-proof.
  • Design: New molds, tightly structured, stretching design to prevent deformation, concave and convex for splicing.
  • Durability: Anti-drop height of 3.8 meters (for free welding/stitching models).

7.2 Product Dimensions

18650 Product Size
Figure 7.1: 18650 Product Sizes (Regular and Enhanced versions have the same size).
  • 1x 18650: 78mm (L) x 20.86mm (W) x 20mm (H)
  • 2x 18650: 78mm (L) x 39.53mm (W) x 20mm (H)
  • 3x 18650: 78mm (L) x 58.01mm (W) x 20mm (H)
  • 4x 18650: 78mm (L) x 76.57mm (W) x 20mm (H)
21700 Product Size
Figure 7.2: 21700 Product Sizes (Regular and Enhanced versions have the same size).
  • 1x 21700: 83mm (L) x 23.8mm (W) x 21.8mm (H)
  • 2x 21700: 83mm (L) x 45.19mm (W) x 21.8mm (H)
  • 3x 21700: 83mm (L) x 66.59mm (W) x 21.8mm (H)
  • 4x 21700: 83mm (L) x 87.98mm (W) x 21.8mm (H)

7.3 Electrical Parameters

Product Parameters Table
Figure 7.3: Detailed product parameters including size, weight, shrapnel material, internal resistance, and continuous current.
Table 7.1: Product Parameters (Summary)
Battery TypeShrapnel MaterialInternal Resistance (mΩ)Continuous Current (A)
21700 (1-4 battery)Manganese steel with nickel plating11.463-5A
18650 (1-4 battery)Manganese steel with nickel plating11.463-5A
21700 reinforce (1-4 battery)Nickel-plated copper0.6924-35A
18650 reinforce (1-4 battery)Nickel-plated copper0.6924-35A
Table 7.2: PCB Layout Parameters
Battery TypeSpacing between positive and negative pole pins (mm)Spacing of pins at the same level (mm)Inner diameter of the pad (mm)Welding pad outer diameter (mm)
21700 (1-4 battery)7824.13 (1-battery), 21.39 (2-4 battery)24
18650 (1-4 battery)7121 (1-battery), 18.5 (2-4 battery)24

8. User Tips

  • Users have reported that the battery holders provide a good, secure fit for batteries.
  • Consider the enhanced version for applications requiring higher current output.
  • Always double-check polarity before inserting batteries to prevent damage.

9. Warranty and Support

9.1 Manufacturer Information

Manufacturer: chengdu heltec energy Technology Co., Ltd
Address: No.16th Chenghong Rd., Chengdu, SiChuan, China.
Email: echo@heltec-bms.com

9.2 EU Authorized Representative

Representative: eVatmaster Consulting GmbH
Address: CN-Bettinastr.30, 60325 Frankfurt am Main, Germany
Tel: 0049-6995179070
Email: contact@evatmaster.com

For technical support or warranty inquiries, please contact the manufacturer or the relevant authorized representative.

10. Additional Resources

10.1 Application Scenarios

Scenarios for using assembled battery compartments
Figure 10.1: Examples of assembled battery compartments suitable for small chargers, energy-saving space, and creative products.
Pin-type application scenarios
Figure 10.2: Pin-type application scenarios suitable for model aircraft, current groups of PCB boards, small power supplies, etc.

10.2 Manufacturer Overview

Video 10.1: An overview of the manufacturing facility where Heltecbms products are produced.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.