Ultenic T20 Pro

Contents

Ultenic T20 Pro Robot Vacuum Cleaner User Manual

Model: T20 Pro

Brand: Ultenic

1. Important Safety Instructions

Basic precautions should always be observed when using any electrical equipment, including the following:

WARNING:

  • READ ALL SAFETY INSTRUCTIONS AND THE ENTIRE MANUAL. Failure to heed the warnings and instructions may result in electric shock, fire, or serious injuries. Please read all instructions before using this device.
  • This device is intended for children 8 years of age and older. People with reduced physical, sensory, or intellectual abilities, or those who lack experience and knowledge should be supervised or instructed in safely using the device; they must also be aware of possible hazards. Children should not play with this device. Cleaning and maintenance should not be performed by children without supervision.

To reduce the risk of injury or damage, please observe the following safety precautions when installing, using and maintaining the device:

  • Please read all instructions regarding safety and operation before using the device.
  • Keep the safety and user manual for future reference. If you accidentally lose the manual, you may visit the official website to download the electronic version. A PDF version of this manual is available at Ultenic T20 Pro User Manual (PDF).
  • Follow all operating and usage instructions.

Restrictions

  • Please read all contents of this manual carefully before using this product.
  • Please do not use the Vacuum Cleaner to vacuum detergent, kerosene, glass dregs, needles, wet items, sewage, matches and other items.
  • Please do not use the Vacuum Cleaner to vacuum toys, paper balls and other large objects, otherwise it will cause blockage of the Vacuum Cleaner, motor burnout and other failures.
  • Please keep the Vacuum Cleaner away from fire and other hot places.
  • Please make sure to install the filter modules and the roller brush of the floor brush.
  • Please make sure not to block the suction inlet or block the roller brush, as this may cause motor failure when using the Vacuum Cleaner.
  • Please do not pour or spill water or other liquids into the machine to avoid short circuits and burning out the machine.
  • Please fully charge the battery when using a new battery or the battery used for the first time after long-term storage. Please ensure that it is charged and discharged at least every three months when the machine is not used for a long time.
  • The appliance is only to be used with the power supply unit provided with the appliance.
  • The plug must be removed from the socket-outlet before cleaning or maintaining the appliance.
  • When cleaning the Vacuum Cleaner, use a dry cloth to wipe it. Do not use gasoline, banana water and other cleaners that are easy to crack or fade the shell.
  • Please do not use or store the Vacuum Cleaner in high temperature, low temperature and other adverse conditions, and do not use them outdoors or on wet surfaces. It is recommended to use them indoors at an ambient temperature of 0-30°C. Please store it in a cool and dry place, and do not expose it to sunlight for a long time.
  • Do not allow children to use or play with the Vacuum Cleaner.
  • When the Vacuum Cleaner can not work, it must be tested and repaired at the designated service center. Do not disassemble the machine by yourself. Waste battery packs should be safely recycled and disposed of, please do not dispose of them at will.
  • If the power cord is damaged, to avoid danger, you must go to the manufacturer's local maintenance department or similar department to have it replaced by a professional.

2. Product Overview

Familiarize yourself with the components of your Ultenic T20 Pro Robot Vacuum Cleaner.

Ultenic T20 Pro Robot Vacuum Cleaner and Auto-Emptying Dock with App Interface
The Ultenic T20 Pro Robot Vacuum Cleaner with its auto-emptying dock and a view of the mobile app interface.

Main Unit Components:

  • Dust Bucket: Collects debris during vacuuming.
  • LED Display: Shows status, battery level, and error codes.
  • Outlet HEPA: Filters exhaust air.
  • Suction Power: Indicates current suction level.
  • ON/OFF Button: Powers the device on or off.
  • Battery: Provides power for operation.
  • Dust Bucket Release Button: For removing the dust bucket.
  • Dust Bucket Cover Release Button: For opening the dust bucket.
  • Battery Pack Release Button: For removing the battery pack.

Accessories:

  • Folding Tube: Connects the main unit to the floor brush. Features a folding tube adjustment button.
  • Upholstery Tool: Designed for delicate fabrics.
  • Long Crevice Nozzle: For tight spots and narrow gaps.
  • Water Tank: For mopping function.
  • Power Adaptor: For charging the device.
  • Floor Brush: Main cleaning head.
  • Mop Cloth: Attaches to the water tank for mopping.
  • Charging Dock/Emptying Base: For automatic dust collection and charging.

3. Assembly

Before assembly, ensure the vacuum cleaner is powered off.

3.1. Battery Installation and Removal

  1. Installation: Insert the battery pack into the main body until you hear a click sound from the battery pack release button.
  2. Removal: Press the battery pack release button and pull out the battery pack.
Diagram showing battery installation and removal
Illustration of how to install and remove the battery pack from the main unit.

3.2. Metal Tube and Floor Brush Installation

Connect the metal tube and the floor brush to the main body in turn. A clicking sound from the metal tube connection button and the floor brush connection button indicates a proper connection.

3.3. Installing Accessories (Upholstery Tool, Crevice Tool)

  • Upholstery Tool: Attach this tool to gently lift dirt and dust from delicate upholstery fabrics.
  • Crevice Tool: Attach this tool for deep cleaning in tight spots like edges, corners, and narrow gaps.

3.4. Dust Bucket Removal and Installation

  1. Remove: Press both dust cup release buttons simultaneously with one hand, and remove the dust cup upwards with the other hand.
  2. Install: Align the dust cup limit buckle, press down the dust cup until you hear a click sound.

3.5. Mopping Function Setup

The water tank assembly can be attached to the bottom of the floor brush for simultaneous vacuuming and mopping.

  1. Fill the tank with water, evenly dampen the mop pad, then attach both the mop pad and the water tank.
  2. Fix the water tank firmly onto the floor brush.
  3. Press the "Open" button to activate the water flow system, which releases water through air pressure difference.
  4. After cleaning, pour out remaining water and press "Close" to prevent floor wetting.

Important Notes for Mopping:

  • Clean mop pad after each room.
  • Never add cleaning solutions (risk of corrosion).
  • The water-filled tank increases overall weight and operating resistance - this integrated design is industry-standard for combo units.

3.6. Using the Telescopic Tube

Press the folding tube adjustment button to fold the tube. Lift the folding tube upward until you hear a clicking sound to straighten it.

3.7. Wall Hanger Installation and Use

  1. Install the wall hanger: Insert expansion tubes into pre-mounting holes on the wall. Thread two fixing screws through the wall hanger's mounting holes, align with expansion tube holes, insert screws, and tighten clockwise.
  2. Use the wall hanger: After fixing the wall mount, hang the vacuum on it. Insert the vacuum cleaner's attachment into the side wall mount's fixing holes. Insert the adapter into the charging wall mount's hole. The machine will charge automatically when hung.
Diagram showing the robot vacuum charging on its wall-mounted dock
The robot vacuum automatically recharges when docked on the wall hanger.

4. Operation

4.1. Charging the Vacuum

  1. Insert the charging adapter plug into an AC outlet, then insert the adapter charging head into the main unit for direct charging.
  2. You can also dismantle the battery pack and use the adapter to charge it separately.
  3. Insert the charging adapter into the charging wall mount, and then put the host directly on the wall mount for charging.

4.2. Switching On/Off and Switching Gears

Robot vacuum cleaner display showing battery and mode settings
The robot vacuum's LED display showing battery level and cleaning mode.
  • Power Button: Click the power button to turn the machine on, and click it again to turn it off.
  • Cleaning Modes: The machine defaults to ECO gear. Click the adjustment button again to switch to NORMAL gear, then again to TURBO gear. The machine will shut down if the power button is clicked in any gear.
  • Charge Protection: 100% battery is displayed when fully charged.
  • Low Battery Indicator: When battery is below 10%, the display screen will not flash, but the "min" icon will flash until the device powers off.
  • Empty Battery: If the device is out of battery and the power button is pressed, the number "0" will display and flash twice per second for 5 seconds, with the "min" indicator staying steadily lit. The device cannot be started.

4.3. Lamp Display Situations

  • HEPA Filter Not Installed: The HEPA missing warning indicator flashes red and turns off after 8 seconds. The host unit will not power on.
  • HEPA Cleaning Reminder: After 15 hours of use, the HEPA cleaning indicator will flash green. Clean the HEPA filter and press and hold the "Mode" speed adjustment button for 5 seconds to reset. The HEPA cleaning light will then turn off.
  • Floor Brush Blocking Protection: If the floor brush is blocked, it will stop after 1 impact. The host will not stop, but the icon will flash at 0.6Hz for 8 seconds. If the floor brush stops blocking, the host will not stop.
  • Duct Clogging Protection: If duct clogging is identified, the icon will blink at 0.6Hz for 8 seconds before shutdown.

5. Maintenance

5.1. Clean the Dust Bucket and Filter

If the vacuum cleaner is blocked or suction drops significantly, the HEPA should be cleaned.

  1. Take down the dust bucket.
  2. Remove the HEPA filter from the dust bucket.
  3. Remove dust from the HEPA, knock the HEPA or wash it with clean water.
  4. Dry the HEPA in the sun.
  5. Put it back into the dust bucket after the HEPA is completely dried.

Do not bend or twist the HEPA during cleaning or rinsing. The HEPA can only be used after being completely dried.

5.2. Cleaning the Electric Floor Brush

  1. Push the lock button down to the unlocked state, and take out one end of the roller brush and pull out the whole brush. Note: Some dust may fall out when pulled.
  2. Clean up any wound hair or debris on the roller brush. If washed with water, it must be dried after rinsing before it can be put back to use.

6. Troubleshooting

Refer to the table below for common issues and their solutions.

Fault Possible Issues Solution
The machine cannot be started The battery is not installed correctly
The battery is dead
The dustbin is full
Please install the battery correctly
Charge the battery
Please empty the rubbish in the dustbin
Vacuum cleaner has no suction/suction becomes smaller The suction of the dust pipe or floor brush is blocked by a foreign body
Dustbin or HEPA is not installed correctly
Filter HEPA blockage
Clean up the suction of the dust pipe or floor brush
Reinstall the dustbin and HEPA
Clean and filter HEPA, dry it and put it back
Dust is leaking from the air outlet HEPA is not installed correctly Install HEPA correctly
The roller brush stops turning, and the floor brush blockage indicator lights up in red The roller brush is entangled or stuck, resulting in protection Clear the winding or blockage and turn it back on
The full dust indicator lights up in red The dustbin is full The dustbin needs to be dumped

Note: This vacuum cleaner must be used with the original battery and power adapter. Do not use the battery for any purpose other than this vacuum cleaner.

7. Specifications

Please use the original charger of this product for charging.

Category Detail
General Brand: Ultenic
Type: Robot Vacuum Cleaner
Model: T20 Pro
Color: Black
Specification Suction Power: 8000Pa
Suction Mode: ECO/Standard/Max
Map Storage: 5 levels
Climbing Height: 15mm
Carpet Boost: YES
2-IN-1 Tank Capacity: 340ml (dustbin) + 250ml (water tank)
Robot Height: 9.7cm
Battery: 3200mAh
Running Time: ≤180min (eco mode)
Charging Time: <6H
Noise Level: ≤60dB
Quick Mapping: 10-15min
Weight & Size Product Weight: 5.7kg
Package Weight: 7.8kg
Product Size (L x W x H): 320x320x97mm
Package Size (L x W x H): 400x400x350mm
Working Voltage 29.6V
Adapter Rated Input 100-240V~50/60Hz
Adapter Rated Output 36V = 0.5A

Package Contents:

Diagram showing all items included in the Ultenic T20 Pro package
Visual representation of the Ultenic T20 Pro Robot Vacuum Cleaner package contents.
  • 1 x Robot Vacuum Cleaner (with 2-in-1 Dust Bin and Water Tank)
  • 1 x Charging Dock/Emptying Base
  • 1 x Mop Holder
  • 2 x Dust Bags
  • 2 x HEPA Filters (1 installed + 1 spare)
  • 2 x Side Brushes (1 installed + 1 spare)
  • 2 x Mops (1 installed + 1 spare)
  • 1 x Cleaning Brush
  • 1 x Cleaning Solution
  • 1 x User Manual
  • 1 x Quick Start Guide

8. User Tips

  • Regular Filter Cleaning: To maintain optimal suction and prevent dust leakage, regularly clean the HEPA filter and dustbin. Reset the HEPA cleaning reminder in the app after cleaning.
  • Obstacle Avoidance: While the AI obstacle avoidance is advanced, it's always a good practice to clear larger obstacles and loose cables from the cleaning path to ensure uninterrupted operation.
  • Mopping Best Practices: For best mopping results, ensure the mop pad is evenly dampened and clean it after each room. Avoid using harsh cleaning solutions in the water tank to prevent corrosion.
  • Map Management: Utilize the multi-map management feature to store floor plans for different levels of your home. Customize cleaning modes, restricted areas, and room names for efficient and tailored cleaning.
  • Scheduled Cleaning: Take advantage of the smart cleaning schedule feature in the app to program your robot to clean automatically, fitting seamlessly into your daily routine.

9. Frequently Asked Questions (FAQ)

Q: How do I connect the robot vacuum to my home Wi-Fi?
A: Download the Ultenic app, create an account, and follow the in-app instructions to connect your T20 Pro to your Wi-Fi network. Ensure your phone is connected to a 2.4GHz Wi-Fi network during setup.
Q: Can the robot vacuum clean in the dark?
A: Yes, the Ultenic T20 Pro uses LiDAR navigation, which works effectively in low-light conditions or complete darkness to map and navigate your home.
Q: What should I do if the robot gets stuck frequently?
A: Check for common obstacles like loose cables, thick rugs, or furniture it might get wedged under. Use the 'No-Go Zones' feature in the app to mark areas where the robot frequently gets stuck.
Q: How often should I replace the HEPA filter and side brushes?
A: The replacement frequency depends on usage. Generally, HEPA filters should be replaced every 3-6 months, and side brushes every 6-12 months. Check the app for maintenance reminders.

10. Warranty and Support

For after-sales service, warranty registration, or to replace any accessories, please contact Ultenic customer support.

Customer Service:

Email: support@proscenic.com

Manufacturer:

Shenzhen Proscenic Technology Co., Ltd.
Suzhou RIBNO ElectricAppliance Co.,Ltd.(Authorized)
Add: No.408 Mudong Road, Mudu Town, Wuzhong District, 215101 Suzhou, China

UK Representative:

Goal Reach Consulting Ltd.
Office 1029, 3 Hardman Street, 10th Floor, Spinningfields, Manchester M3 3HF, UK
E-mail: goalservice@hotmail.com

EC Representative:

ULT Europe GmbH
Kreuzstraße 60, Düsseldorf, North Rhine-Westphalia, 40210, Germany
E-mail: support@proscenic.com

Declaration of Conformity: This product conforms to IECE60312.


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.