1. Introduction
This manual provides essential information for the proper installation, operation, and maintenance of your Flipsky 2.4G Wireless Remote Controller Receiver. This receiver is designed for use with various Flipsky remote controllers, including VX1, VX1Pro, VX2, VX3, VX3Pro, and VX4Pro, in applications such as electric skateboards, e-scooters, efoils, and esurfs.
Please read this manual thoroughly before using the product to ensure safe and optimal performance.
Video 1: Product overview of the Flipsky receiver.
2. Package Contents
- Flipsky 2.4G Wireless Remote Controller Receiver (specific model may vary)
- Connection wires (may be pre-attached or included separately depending on receiver variant)
- External antenna (for models requiring one)
Figure 1: Example of a Flipsky receiver with integrated antenna and pre-attached signal wires.
3. Setup and Installation
3.1. Connection to ESC
- Identify the receiver port on your Electronic Speed Controller (ESC). This is typically a 3-pin port labeled 'PPM', 'UART', or 'Receiver'.
- Connect the receiver to the ESC using the provided wires. Ensure correct polarity: Signal (usually white/yellow), Positive (red), and Ground (black/brown). Refer to your ESC manual for specific pinouts.
Figure 2: Flipsky receiver board with external wire antenna and flat patch antenna, showing connection points.
3.2. Antenna Placement
- For receivers with external antennas (wire or patch type), ensure the antenna is positioned away from large metal objects, carbon fiber, or other components that could shield the signal.
- Mount the antenna in a location that provides clear line-of-sight to the remote controller for optimal signal reception. Do not bend or cut the antenna wire.
3.3. Mounting the Receiver
- Secure the receiver firmly within your device (e.g., skateboard enclosure) using double-sided tape or other appropriate mounting hardware.
- Ensure the receiver is protected from physical damage, moisture, and excessive vibration.
3.4. Binding with Remote Controller
The binding process pairs your receiver with your specific Flipsky remote controller. The exact steps may vary slightly by remote model, but generally follow this procedure:
- Ensure both the receiver (powered via ESC) and the remote controller are turned off.
- Turn on your remote controller and put it into binding mode (refer to your remote's manual for specific instructions, often involves holding a button while powering on).
- Power on the receiver (by powering on your ESC/device). The receiver's LED should indicate it is searching for a signal (e.g., blinking rapidly).
- Once the remote and receiver successfully bind, the receiver's LED will typically become solid, indicating a stable connection.
- Turn off both the remote and receiver, then power them on again to confirm the binding is saved and functional.
Important: Ensure your remote controller firmware and receiver are compatible. Older remote versions may not bind with newer receivers, and vice-versa.
4. Operating Instructions
Once properly installed and bound, the receiver operates automatically. Its primary function is to receive signals from your Flipsky remote controller and transmit them to the ESC to control your device.
- Always turn on your remote controller first, then power on your device (which powers the receiver).
- Observe the receiver's LED indicator. A solid light typically indicates a successful connection.
- Before operating, perform a quick functional check to ensure throttle and steering/control inputs respond correctly and safely.
- When finished, power off your device first, then turn off your remote controller.
5. Maintenance
- Keep Dry: Although the receiver is described as waterproof, it is best practice to avoid prolonged exposure to water or extreme moisture to prevent potential damage to electronic components. Ensure all connections are dry before powering on.
- Clean Connections: Periodically inspect all wire connections for corrosion or looseness. Ensure they are clean and securely seated.
- Antenna Inspection: Check the antenna for any physical damage, kinks, or cuts. A damaged antenna can severely reduce signal range and reliability.
- Physical Protection: Ensure the receiver remains securely mounted and protected from impacts or excessive vibrations.
6. Troubleshooting
6.1. Receiver Not Binding
- Compatibility: Verify that your remote controller model and firmware version are compatible with the receiver. Some older remote versions may not bind with newer receivers.
- Binding Procedure: Double-check that you are following the correct binding procedure for both your remote and receiver.
- Power Cycle: Try power cycling both the remote and receiver multiple times during the binding process.
- Interference: Ensure there are no strong 2.4GHz interference sources nearby during binding.
6.2. No Signal or Intermittent Connection
- Antenna Placement: Ensure the receiver's antenna is not obstructed by metal, carbon fiber, or other materials. Reposition the antenna for better line-of-sight.
- Antenna Damage: Inspect the antenna for any damage. Replace if necessary.
- Power Supply: Verify the receiver is receiving stable power from the ESC.
- Range: Test the connection at a closer range to rule out range issues.
- Re-bind: Attempt to re-bind the receiver to the remote controller.
7. Specifications
| Feature | Specification |
|---|---|
| Brand | FLIPSKY |
| Wireless Frequency | 2.4 GHz |
| Compatibility | Flipsky VX1, VX1Pro, VX2, VX3, VX3Pro, VX4Pro Remote Controllers |
| Material | Composite Material |
| Application | Electric Skateboard, E-Scooter, Efoil, Esurf |
| Water Resistance | Waterproof (for DIY Electric Skateboard E-Scooter applications) |
8. User Tips
- Verify Compatibility: Before attempting to bind, always confirm that your specific remote controller model (e.g., VX2 Version 1) is compatible with the receiver you have purchased. Firmware differences can prevent binding.
- Binding Patience: The binding process can sometimes be finicky. If it doesn't work on the first try, power cycle both devices and try again, ensuring you follow the steps precisely.
- Antenna Care: A well-placed and undamaged antenna is crucial for reliable connection. Avoid coiling or placing the antenna near power wires or metal.
9. Warranty and Support
For warranty information, technical support, or service inquiries, please contact your retailer or the manufacturer directly. Keep your proof of purchase for warranty claims.