1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your CO LIGHT 3-inch Motorcycle Fog/Driving Lights. Designed for off-road use, these LED auxiliary lights feature Amber DRL and White light options, IP67 waterproofing, and are suitable for motorcycles, ATVs, SUVs, and other vehicles. Please read this manual thoroughly before installation and use to ensure proper function and safety.
2. Product Overview
The CO LIGHT 3-inch Motorcycle Fog/Driving Lights are high-intensity LED lights designed to enhance visibility and safety in various driving conditions. They feature multiple lighting modes and robust construction for durability.
2.1 Key Components
- High-Intensity LEDs: 11000LM/PC, 100W/PC for powerful illumination.
- Glass Reflector: Tempered glass spot reflector for better transparency.
- Amber DRL: 10W strong penetration, follows motor start-up.
- Die-Cast Aluminum Housing: Provides durability and efficient heat dissipation.
- PMMA Lens: Durable lens material.


2.2 Available Models
- D040-AWY: High Low Beam White + Yellow DRL with Dimmer Switch Strobe.
- D040-AY: High Low Beam Yellow DRL with Ordinary Switch Strobe.
- D040-AW: High Low Beam White DRL with Ordinary Switch Strobe.

3. Setup and Installation
3.1 Package Contents
Before installation, verify that all components are present:
- 2x LED Work Lights
- Wire Harness (with relay, fuse, and switch)
- Mounting Brackets (U-shaped or Tube Support, depending on selection)
- Necessary mounting hardware (screws, nuts, washers, Allen key)
- Amber/Yellow covers (optional, depending on model)
- Cable ties

3.2 Mounting the Lights
The lights offer flexible installation options with four-sided openings for 360° adjustment. Choose a suitable location on your motorcycle, ATV, or SUV that provides optimal light projection and does not obstruct other vehicle functions.
- Attach the chosen mounting brackets to the lights using the provided hardware.
- Secure the lights to your vehicle. Common mounting points include crash bars, handlebars, or dedicated auxiliary light mounts.
- Adjust the angle of the lights for desired beam direction.



3.3 Wiring Instructions
The lights come with a motor wire harness for simplified connection. Refer to the wiring diagrams below for correct installation.
- Connect the positive (+) wire from the harness to your vehicle's battery positive terminal.
- Connect the negative (-) wire from the harness to your vehicle's battery negative terminal or a suitable ground point.
- Connect the ACC wire to an ignition-switched power source (e.g., accessory circuit) so the DRL automatically turns on with the vehicle.
- Connect the High Beam Positive wire to the original vehicle's high beam circuit. This allows the lights to flash for 3 seconds when the horn is activated (if configured).
- Connect the Overtake wire (if present on your model) to a momentary switch or the vehicle's overtake signal to activate the high beam.
- Plug the 4-pin or 5-pin waterproof IP68 connectors from the lights into the corresponding connectors on the wire harness.
- Secure all wiring to prevent chafing or interference with moving parts.


4. Operating Instructions
The CO LIGHT 3-inch Motorcycle Fog/Driving Lights offer various lighting modes controlled by the included switch.
4.1 DRL Automatic On
When powered, the DRL (Daytime Running Light) function will automatically activate.
4.2 Mode Switching (Dimmer Switch - D040-AWY)
For models with a dimmer switch (e.g., D040-AWY), the following operations apply:
- Short Press to Toggle: Cycle through Low Beam, High Beam, and High & Low Beams.
- Short Press: One-click off.
- Long Press 1st Time: High Beam Strobe.
- Long Press 2nd Time: High Beam Alternating Strobe.
- Long Press 3rd Time: Low Beam Cycle Flash.
- Long Press (DRL button): Turn DRL Off / On.


4.3 Mode Switching (Ordinary Switch - D040-AY, D040-AW)
For models with an ordinary switch, the following operations apply:
- When high beam is on: Click to flash the high beam simultaneously/alternately.
- When high beam is not on: Click to flash the low beam simultaneously/alternately.
- Brightness Adjustable: (100/80/60/40%) for both low/high beam in steady and flash modes.

4.4 Light Performance
- Amber DRL: Car Start DRL lighting.
- White High Beam: 25W*2 Long Spot Beam.
- Yellow Low Beam: 25W*2 Even Beam Pattern.
- Combo High Beam: 25W*4 Longer Shooting.




Video 1: Product demonstration of various light modes and functions.
5. Maintenance
These LED lights are designed for durability and require minimal maintenance. Follow these guidelines to ensure long-lasting performance:
- Cleaning: Regularly clean the lens with a soft cloth and mild soap solution to remove dirt and debris. Avoid abrasive cleaners that could scratch the lens.
- Inspection: Periodically check all mounting hardware and wiring connections to ensure they are secure and free from corrosion or damage.
- Waterproofing: The lights are IP68 rated, meaning they are protected against dust and immersion in water. Ensure all connections are properly sealed during installation to maintain this rating.
- Cooling Fins: The die-cast aluminum cooling fins are designed for efficient heat dissipation. Keep them clear of obstructions to prevent overheating.



6. Troubleshooting
If you encounter issues with your CO LIGHT 3-inch Motorcycle Fog/Driving Lights, refer to the following common problems and solutions:
- Lights not turning on:
- Check all wiring connections for looseness or corrosion.
- Verify the fuse in the wire harness is intact. Replace if blown.
- Ensure the battery has sufficient charge.
- Test the switch for proper functionality.
- Flickering lights:
- Inspect wiring for loose connections or damaged insulation.
- Ensure stable power supply from the vehicle.
- One light not working:
- Check the specific connection for that light.
- Swap the light with the working one to determine if the issue is with the light unit or the wiring.
If problems persist after attempting these solutions, please contact customer support.
7. Specifications
| Feature | Specification |
|---|---|
| Light Source | 5-inch High Power High Intensity LED Chips |
| Voltage | 9~32V DC |
| Color Temperature | 6500K |
| Luminous Flux | 90000LM (Total) |
| Wattage | LED Work Light Bar (Implied 100W/PC from image) |
| Lens Material | PMMA |
| Housing Material | Die-cast Aluminum |
| Mounting Brackets | Aluminum, Middle bracket (U-shaped or Tube Support) |
| Ingress Protection | IP68 |
| Lifespan | 50,000 hours |
| Certification | ISO9001, CE, ROHS |
| Operation Temperature | -40°C ~ 80°C |
| Beam Angle | Combo (Driving Beam) |
| Application Scenarios | Off-road (Motorcycle, ATV, SUV, Truck, Forklift, Trains, Boat, Special Vehicles, Engineering Vehicles) |
7.1 Product Dimensions



8. User Tips
- For optimal visibility, ensure the lights are aimed correctly. Adjust the beam angle to avoid blinding oncoming traffic while maximizing your field of view.
- Consider using the Amber DRL function during daytime for increased conspicuity, especially in adverse weather conditions.
- Regularly check the tightness of mounting bolts, especially after off-road use, to prevent vibration-induced loosening.
- If installing on a motorcycle, ensure the wiring is routed away from hot engine parts and moving components to prevent damage.
9. Warranty & Support
CO LIGHT products are backed by a 5-year warranty, ensuring quality and reliability. For any technical assistance, troubleshooting beyond this manual, or warranty claims, please contact CO LIGHT Global Store customer support directly.
CO LIGHT Global Store
Opened: March 1, 2024