JIKONG PB Serial BMS Communication Board

Contents

JIKONG Communication Board for PB Serial BMS User Manual

Model: PB Serial BMS Communication Board

1. Introduction

The JIKONG Lithium Battery Intelligent Protection Board (BMS) is a management system designed for large capacity series lithium battery packs. It features voltage acquisition, high current active balancing, overcharge/over-temperature protection, coulomb meter, Bluetooth communication, and host computer monitoring. It supports lithium iron phosphate and ternary lithium battery types.

The board utilizes energy transfer active balancing technology to achieve a continuous 1A/2A balance current, ensuring battery consistency, extending range, and delaying aging. It comes with a mobile APP (Android/iOS) for checking battery status, modifying parameters, and controlling charge/discharge switches. Its compact size and comprehensive functions make it suitable for high-power energy storage, base station backup power, and solar power systems.

2. Key Features

  • LED Bluetooth status indicator
  • APP Bluetooth remote operation
  • Battery capacity calculation
  • Supports PC operations
  • High precision voltage acquisition (±3mV)
  • High precision current acquisition
  • Support information screen display
  • Accurate time logging
  • RS485 communication support
  • CAN communication support
  • Heating function support
  • Alarm dry contact function
  • Charge overcurrent protection
  • Charge overvoltage protection
  • Charge over temperature protection
  • Low temperature protection during charge
  • Discharge overcurrent protection
  • Discharge undervoltage protection
  • Discharge over temperature protection
  • Short circuit protection
  • Battery parallel current limiting function

3. Specifications

3.1. Basic Parameters

ParameterValueUnit
Supply Voltage20-70V
Standby Power Consumption12mW
Operating Power Consumption1100mW
Operating Temperature-30-70°C
Maximum Number of Collection Strings16S
Maximum Balancing Current1-2A
Maximum Charging Current (10P)100A
Maximum Charging Current (15P)150A
Maximum Charging Current (20P)200A
Maximum Discharge Current (10P)100A
Maximum Discharge Current (15P)150A
Maximum Discharge Current (20P)200A
Maximum Instantaneous Current (10P)200A
Maximum Instantaneous Current (15P)300A
Maximum Instantaneous Current (20P)400A
Maximum Internal Loop Resistance (10P)1mΩ
Maximum Internal Loop Resistance (15P)0.45mΩ
Maximum Internal Loop Resistance (20P)0.35mΩ
Protective Plate Size300*100*24mm
Finished Weight1000g

3.2. Default Parameters

ParameterLi-ion (Default)LiFePO4 (Default)LTO (Default)Unit
Balancing Initial Voltage332V
Maximum Balancing Current1-21-21-2A
Unit Overcharge Voltage4.23.62.7V
Single Overcharge Protection Recovery4.173.542.64V
Monomer Undervoltage Protection2.822.61.8V
Single Undervoltage Protection Recovery2.852.651.85V
Automatic Shutdown Voltage2.82.51.7V
SOC-0% Voltage2.92.61.85V
SOC-100% Voltage4.183.52.65V
Trigger Balancing Differential Pressure0.010.010.01V
Charging Overcurrent Protection Delay333S
Charging Overcurrent Protection Release Time606060S
Discharge Overcurrent Protection Delay300300300S
Discharge Overcurrent Protection Release Time606060S
Short-circuit Protection Delay555µS
Short-circuit Protection Release Time303030S
Charging Overtemperature Protection Temperature707070°C
Charge Overtemperature Restore Temperature606060°C
Discharge Overtemperature Protection Temperature707070°C
Discharge Overtemperature Recovery Temperature606060°C
Charging Low Temperature Protection Temperature-20-20-20°C
Charge Low Temperature Restore Temperature-10-10-10°C
MOS Overtemperature Protection Temperature100100100°C
MOS Overtemperature Protection Recovery Temperature808080°C
Device Address000/

3.3. Other Product Properties

  • Certification: CE
  • Balance Function: Active Balanced BMS
  • Hardware or Smart: SMART BMS
  • Charge and Discharge Port: Common Port BMS
  • Type: LIFEPO4 Battery BMS
  • Origin: Mainland China
  • Function: Overcharge Protection, Over Discharge Protection, Overcurrent Protection, Short Circuit Protection
  • Usage Scenario: Power BMS, Energy Storage BMS, 3C Digital BMS
  • Charging Current: 10A

4. Product Overview

The JIKONG Communication Board is designed to work with specific PB Serial BMS models. Ensure compatibility before use.

JIKONG Communication Board and compatible BMS models
Figure 1: JIKONG Communication Board and compatible PB Serial BMS models.

4.1. Product Dimensions

The dimensions of the JIKONG PB1/2A16S-10/15/20P series protection board are 300mm × 100mm × 24mm.

Dimensions of the JIKONG PB1/2A16S-10/15/20P series protection board
Figure 2: Dimensions of the JIKONG PB1/2A16S-10/15/20P series protection board.

4.2. Interface Board Diagram

The interface board includes various connectors, LEDs, and DIP switches for configuration and communication.

Interface board diagram with connectors and DIP switches
Figure 3: Interface board diagram showing connectors and DIP switches.
Close-up of the interface board showing DIP switches and LEDs
Figure 4: Close-up of the interface board showing DIP switches and LEDs.

4.3. Connector Pin Definitions

ConnectorPin No.Pin NameDefinition
P1 (Interface Board)Interface board interface
P4 (URAT Display Interface)1K-Activation signal negative electrode
2K+Activate the positive signal
3GNDNegative terminal
4RXUART RX, 5V
5TXUART TX, 5V
6VCCDisplay power output
P5 (Display Interface)1VCCDisplay power output
2ADisplay RS485 signal negative
3BDisplay RS485 signal positive
4GNDNegative terminal
5K+Activate the positive signal
6K-Activation signal negative electrode
P6 (Acquisition Interface)1NT1Connect the NTC1 temperature probe
2GNDConnect the NTC1 temperature probe
3B0Total negative battery
4B1The first battery positives
5B2The second battery positive
6B3The third battery positive
7B4The fourth battery positive
P7 (Acquisition Interface)1NTC2Connect the NTC2 temperature probe
2GNDConnect the NTC2 temperature probe
P8 (Acquisition Interface)1NT3Connect the NTC3 temperature probe
2GNDConnect the NTC3 temperature probe
3B8Reserved pin
P9 (Acquisition Interface)1NT4Connect the NTC4 temperature probe
2GNDConnect the NTC4 temperature probe
P10 (Heating Interface)1HT-Heater element negative electrode
P11 (Power Input)1B+Power input positive
D1 (Bluetooth Connection Indicator)Steady on when connected, blinking when disconnected.
P-Connect to external load or negative terminal of charger (M6 screw)
B-Connect to the negative battery terminal (M6 screw)

4.4. DIP Switch Settings for Device Address

The DIP switches are used to set the device address for parallel function. The address range is 0-15.

AddressDIP Switch 1DIP Switch 2DIP Switch 3DIP Switch 4
0 (Host)OFFOFFOFFOFF
1 (Slave)ONOFFOFFOFF
2 (Slave)OFFONOFFOFF
3 (Slave)ONONOFFOFF
...............
15 (Slave)ONONONON

Note: ON indicates the LED is on, OFF indicates the LED is off.

Example of DIP switch settings for slave address 1
Figure 5: Example of DIP switch settings for slave address 1.
Example of DIP switch settings for slave address 2
Figure 6: Example of DIP switch settings for slave address 2.

5. Setup and Installation

5.1. Wiring Method

The JIKONG PB1/2A16S-10/15/20P series protection board is suitable for 7-16 series lithium battery packs. The specific wiring method varies depending on the number of cells in the battery pack. Always ensure correct polarity and secure connections.

Wiring diagram for JIKONG PB1/2A16S-10/15/20P
Figure 7: Wiring diagram for JIKONG PB1/2A16S-10/15/20P. Consult this diagram for proper connections based on your battery configuration.

5.2. Device Activation

Before powering on the protection board, verify that the balance cable is properly connected and that P- and B- are correctly connected. Ensure the protection board is securely fixed to the battery core. Incorrect connections can lead to malfunctions or damage.

The protection board does not have a power-on control switch. It is designed for charging activation mode, meaning the charger voltage should be 2V higher than the battery voltage. After battery assembly, connect the charger to activate the protection board.

Alternatively, the board supports key activation and display activation. If you have an optional display screen and button, simply insert the cable into the display interface and press the button to activate.

6. Operation

6.1. APP Installation

The mobile APP for this product can be obtained by scanning the QR code below. An Android device with version 7 or higher is required.

QR Code for APP (Image not available in ALLOWED_URLS)
Figure 8: Scan this QR code to download the JIKONG BMS APP.

6.2. Parameter Setting

Parameters can be set via the mobile APP. Refer to the 'Default Parameters' table in Section 3.2 for initial values. Users can adjust settings such as cell count, battery capacity, balance trigger differential pressure, voltage calibration, and current calibration.

6.3. Active Equalization

The protection board uses active equalization to transfer energy from high-voltage cells to low-voltage cells. When the balance function is enabled and the voltage difference between any two battery strings exceeds the set value, equalization automatically starts. It stops when the difference falls below the set value. The default balance current is 1A/2A. It is recommended that the balance current does not exceed 0.2C of the battery capacity. If not needed, the balancing function can be turned off in the APP's BMS control page.

6.4. Heating Function

The board includes a heating function to prevent charging and discharging failures due to low battery activity in cold temperatures. The designed heating current is 10A. Users can enable/disable this function via the APP. It is recommended to install a temperature control switch (45-65°C normally closed type) in series with the heating circuit as a secondary protection to prevent thermal runaway.

6.5. Dry Contact Function

Two dry contacts are provided to control external devices like alarms or fans. When the BMS detects an overtemperature, overcharge, or overdischarge state, the alarm interface can switch the dry contact status to trigger a buzzer or activate a fan. Users can select two trigger conditions and configure them via the APP.

Dry contact wiring diagram
Figure 9: Dry contact wiring diagram for external alarm equipment.

6.6. Protection Functions

The BMS provides comprehensive protection features:

  • Charge Overvoltage Protection: Prevents overcharging by shutting off charging when any cell voltage exceeds the set limit. Charging resumes when all cell voltages drop below the recovery voltage.
  • Discharge Undervoltage Protection: Prevents over-discharging by shutting off discharge when any cell voltage falls below the set limit. Discharge resumes when all cell voltages rise above the recovery voltage. The board will automatically shut down if any cell voltage drops below the automatic shutdown voltage.
  • Charge Overcurrent Protection: Triggers if the charging current exceeds the set continuous charging current for a specified delay. Charging is then stopped and resumes after the overcurrent release time.
  • Discharge Overcurrent Protection: Triggers if the discharge current exceeds the set continuous discharge current for a specified delay. Discharge is then stopped and resumes after the overcurrent release time.
  • Overtemperature Protection: Shuts down charging/discharging if the temperature exceeds the set overtemperature limit. Operation resumes when the temperature falls below the recovery value.
  • Low Temperature Protection: Shuts down charging if the temperature falls below the set low temperature limit. Charging resumes when the temperature rises above the recovery value.
  • Short Circuit Protection: Automatically protects against short circuits. The delay and recovery times can be adjusted via the APP. If a short circuit occurs during charging or discharging, the board will stop operation and resume after the recovery time.

6.7. Emergency Switch

In case of issues like over-temperature, over-discharge, over-charge, or string drops during normal use, activating the emergency switch via the APP's BMS control page will enable charge and discharge for 30 minutes. This provides an emergency operational period, even if a single cell voltage has reached the automatic shutdown level, to prevent unexpected power loss.

6.8. Intelligent Sleep

The intelligent sleep function can be enabled or disabled via the APP. Its purpose is to reduce the board's energy consumption when in standby (charging and discharging current less than 1A for 26 consecutive hours). The board can be reactivated by pressing a button or connecting a charger.

6.9. Communication Function

The board supports CAN and RS485 communication. The default CAN communication rate is 250K. Users can select the appropriate protocol in the APP based on their inverter brand. It features two RS485 communication interfaces: RS485-1 for communication with inverters and other settings, and RS485-2 for parallel connection of battery packs and communication with a host computer. The default baud rate is 115200. The communication address can be set using the DIP switches (0-15).

6.10. Charge Current Limiting Function

The board includes a charge current limiting function. Users can set the continuous charging current, delay, and release time via the APP. If the charging current exceeds the set limit, the current limiting function activates, maintaining the charging current at approximately 10A to protect the battery.

6.11. Parallel Function

The parallel function allows simultaneous monitoring of multiple BMS units by a host computer via the RS485 bus. To use this function, you will need a USB to RS485 serial port cable and the JIKONG host computer software.

The parallel function supports up to 16 BMS units. Each BMS must have a unique address from 0 to 15. BMS with address 0 acts as the host, and BMS units with addresses 1 to 15 act as slaves. The host computer connects to the host BMS via a USB to RS485 serial port cable. The RS485-2 ports on the BMS units are then connected to each other using RJ45 Ethernet cables in sequence.

Parallel Function Connection Diagram (Image not available in ALLOWED_URLS)
Figure 10: Diagram illustrating the connection of multiple BMS units for parallel function.

6.12. LED Indicators

The board features various LED indicators to show its status:

StatusNormal/Alarm/ProtectionON/OFF IndicatorRUNALML1-L6Instructions
Power OffNormalOFF
BalanceNormalONFlickerOFFBattery based displayOFF
ChargingNormalONFlickerOFFBattery based displayOFF
ChargingOvercurrent, Overtemperature, Overvoltage, Charging FailureONFlickerFlickerBattery based displayOFF
DischargeNormalONFlickerOFFBattery based displayOFF
DischargeOvercurrent, Overtemperature, Undervoltage, Discharge FailureONFlickerFlickerBattery based displayOFF
Other AlarmPassword not changed, Short circuit, TemperatureONFlickerFlickerBattery based displayOFF

6.13. Power LED Description

Capacity (Electric Quantity)Charging (L5-L1)Discharge (L5-L1)
0-20%OFFOFFOFFOFFONOFFOFFOFFOFFON
20-40%OFFOFFOFFONONOFFOFFOFFONON
40-60%OFFOFFONONONOFFOFFONONON
60-80%OFFONONONONOFFONONONON
80-100%ONONONONONONONONONON

Note: ON indicates the LED is on, OFF indicates the LED is off.

7. Maintenance

To ensure optimal performance and longevity of your JIKONG Communication Board, consider the following:

  • Regular Inspection: Periodically check all wiring connections for tightness and signs of wear or corrosion.
  • Cleanliness: Keep the board free from dust and debris. Use a soft, dry cloth for cleaning. Avoid using liquids or abrasive cleaners.
  • Environmental Conditions: Ensure the operating environment remains within the specified temperature range (-30°C to 70°C) and humidity levels to prevent damage.
  • Firmware Updates: Check the JIKONG APP or official website for any available firmware updates for your BMS, as these may include performance improvements or bug fixes.

8. Troubleshooting

If you encounter issues with your JIKONG Communication Board, refer to the following general troubleshooting steps:

  • Check Connections: Verify all wiring, especially the balance cable, P- and B- connections, are secure and correctly polarized.
  • Review LED Indicators: Consult the LED indicator tables in Section 6.12 and 6.13 to understand the current status or any active alarms/protections.
  • APP Diagnostics: Use the JIKONG APP to check battery working status, error codes, and modify parameters. The APP can provide detailed diagnostic information.
  • Protection Triggers: If a protection (e.g., overvoltage, overcurrent, overtemperature) is active, identify the cause and rectify it. The system will typically resume operation once the condition is resolved and the recovery time has passed.
  • Emergency Switch: In critical situations, the emergency switch can provide a temporary operational window (30 minutes) to address issues.
  • DIP Switch Settings: For parallel configurations, ensure the DIP switch settings for device addresses are correct as per Section 4.4.

For more detailed troubleshooting or persistent issues, refer to the official PDF user manual or contact JIKONG technical support.

9. User Tips

No specific user tips or FAQs were available from provided reviews or Q&A content.

10. Support and Documentation

For detailed technical specifications, wiring diagrams, and comprehensive instructions, please refer to the official user manual PDF:

View User Manual (PDF)

This PDF document provides in-depth information that may not be fully covered in this summary manual.

For further assistance, please contact JIKONG customer support.

11. Manufacturing Process Overview

Watch a brief video showcasing the manufacturing process of the JIKONG BMS boards, highlighting the precision and care involved in production.

Video 1: JIKONG BMS Manufacturing Process. This video demonstrates the automated and manual assembly stages of the circuit boards.
Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.