PowMr POW-ELITE10.6KW / POW-LIO48300-IP65

Contents

PowMr 10.6KW Hybrid Inverter & 16kWh 48V LiFePO4 Battery User Manual

Model: POW-ELITE10.6KW / POW-LIO48300-IP65

1. Introduction

This manual describes the assembly, installation, operation, and troubleshooting of the PowMr 10.6KW Hybrid Inverter and 16kWh 48V LiFePO4 Battery system. Please read this manual carefully before installation and operation. Keep this manual for future reference.

This hybrid PV inverter and battery system is designed to provide continuous power to connected loads by utilizing PV power, utility power, and battery power. It is suitable for residential and commercial energy storage systems.

Key features of this combo include:

  • Perfect Communication Match: RS485 and CAN ports are pre-configured for direct BMS communication between the inverter and battery, eliminating the need for extra configuration.
  • Outdoor-Grade Protection: The inverter boasts an IP66 rating, and the battery an IP65 rating, ensuring protection against rain, snow, dust, and high humidity for reliable outdoor operation.
  • Scalable Capacity: The system allows for expansion, starting with one battery and adding more later. Up to 9 inverters and 16 batteries can be paralleled for larger homes or light commercial use.
  • Smart Energy Management: Real-time monitoring of solar generation, battery status, grid usage, and load consumption is available via the inverter's LCD and the i.Solar app.
  • Ultra-Fast UPS Switch: A transfer time of less than 10ms for critical loads ensures uninterrupted power for essential appliances during outages.

A detailed user manual in PDF format is available for download: PowMr Solar Inverter User Manual (PDF)

2. Safety Instructions

⚠ WARNING: This chapter contains important safety and operating instructions. Read and keep this manual for future reference.

  1. Before using the unit, read all instructions and cautionary markings on the unit, the batteries, and all appropriate sections of this manual.
  2. CAUTION – To reduce risk of injury, charge only deep-cycle lead acid type rechargeable batteries. Other types of batteries may burst, causing personal injury and damage.
  3. Do not disassemble the unit. Take it to a qualified service center when service or repair is required. Incorrect re-assembly may result in a risk of electric shock or fire.
  4. To reduce risk of electric shock, disconnect all wirings before attempting any maintenance or cleaning. Turning off the unit will not reduce this risk.
  5. CAUTION – Only qualified personnel can install this device with battery.
  6. NEVER charge a frozen battery.
  7. For optimum operation of this inverter/charger, please follow required spec to select appropriate cable size. It's very important to correctly operate this inverter/charger.
  8. Be very cautious when working with metal tools on or around batteries. A potential risk exists to drop a tool to spark or short circuit batteries or other electrical parts and could cause an explosion.
  9. Please strictly follow installation procedure when you want to disconnect AC or DC terminals. Please refer to INSTALLATION section of this manual for the details.
  10. Fuses are provided as over-current protection for the battery supply.
  11. GROUNDING INSTRUCTIONS - This inverter/charger should be connected to a permanent grounded wiring system. Be sure to comply with local requirements and regulation to install this inverter.
  12. NEVER cause AC output and DC input short circuited. Do NOT connect to the mains when DC input short circuits.
  13. Warning!! Only qualified service persons are able to service this device. If errors still persist after following troubleshooting table, please send this inverter/charger back to local dealer or service center for maintenance.

3. Product Overview

The PowMr Hybrid Inverter and LiFePO4 Battery system is designed for efficient and reliable energy management. Below are the key components and their identification.

3.1. System Diagram

PowMr Inverter and Battery outdoor rated IP66+IP65
Figure 1: PowMr Hybrid Inverter and LiFePO4 Battery system, outdoor rated IP66+IP65.
PowMr 6.6/10.6KW All in One Solar Inverter features
Figure 2: Key features of the PowMr 6.6/10.6KW All-in-One Solar Inverter, including 50Hz/60Hz frequency range, 48VDC battery voltage, MPPT 135/210A max charge current, and 120-450VDC MPPT voltage range.
PowMr 316AH 51.2V LiFePO4 Battery features
Figure 3: Key features of the PowMr 316AH 51.2V LiFePO4 Battery, including 16.1792KWh nominal energy, 200A max charging current, A+ 6000+ cycles, and RS232/RS485/CAN/Dry communication interface.

3.2. Inverter Components

Inverter views (front, top, bottom, internal)
Figure 4: Various views of the inverter, showing its external design and internal components.

The inverter features the following:

  1. PV connectors
  2. AC Grid connectors
  3. Battery connectors
  4. AC output connectors
  5. AC Generator connectors
  6. Sharing current ports & external sensor ports
  7. Parallel communication ports
  8. Dry contact/USB/RS-232/BMS communication ports
  9. LCD display
  10. Cold start button

For parallel model installation and operation, please check the separate parallel installation guide in Appendix I.

3.3. Battery Components

Battery views (front, side, top, internal)
Figure 5: Various views of the battery, showing its external design and internal components.

The battery is a POW-LIO48300-IP65 model, featuring a vertical design with wheels for easy movement and an IP65 rating for outdoor suitability.

3.4. Product Video Overview

Video 1: A brief overview of the PowMr 10.6 kW all-in-one solar inverter, highlighting its design for residential and commercial energy storage, 10600 watts pure sine wave output, adjustable voltage, parallel operation up to nine units (95.4 kilowatts total), dual MPPTs with 1.7 times PV oversizing (18 kilowatts solar input, 500-volt max open-circuit voltage), compatibility with 48-volt lithium or lead-acid batteries, 210 amps charging current, BMS communication, IP66 rating, built-in Wi-Fi, and remote monitoring capabilities.

4. Installation

4.1. Unpacking and Inspection

Before installation, carefully inspect the unit. Ensure that nothing inside the package is damaged. The package should contain the Inverter unit, Software CD, Manual, RS-232 cable, Parallel communication cable, Current sharing cable, Mounting screws, Mounting plate, WiFi antenna, and DC terminals (for 8.6KW, 10.6KW models).

4.2. Preparation and Mounting

Before connecting any wiring, remove the bottom cover by unscrewing the four screws. This hybrid inverter is designed for indoor or outdoor use (IP66), but ensure the installation site meets the following conditions:

  • Not in direct sunlight.
  • Not in areas where highly flammable materials are stored.
  • Not in potential explosive areas.
  • Not in direct cool air.
  • Not near television antenna or antenna cable.
  • Not higher than an altitude of about 2000 meters above sea level.

⚠ WARNING!! FIRE HAZARD. SUITABLE FOR MOUNTING ON CONCRETE OR OTHER NON-COMBUSTIBLE SURFACE ONLY.

Mounting Steps:

  1. Fix two brackets on the two sides of the inverter with 8 screws.
  2. Install the inverter by screwing two screws on the top of two brackets.
  3. Fix the remaining two mounting holes with screws.
  4. The inverter should be installed in a shaded, rain-proof, or protected location.
Inverter front view with 'Hot surface. Do not touch' warning
Figure 6: Inverter front view, showing the LCD display and a 'Hot surface. Do not touch' warning label.

4.3. Battery Connection

⚠ CAUTION: For safety and regulation compliance, install a separate DC over-current protector or disconnect device between the battery and inverter.

⚠ WARNING! All wiring must be performed by qualified personnel. Use appropriate cable for battery connection to reduce risk of injury.

Recommended Battery Cable and Terminal Size:

MODELTypical AmperageWire SizeTorque Value
6.6KW125A1*2AWG1.98 Nm
8.6KW190A1*1/0 AWG5 Nm
10.6KW210A1*1/0 AWG5 Nm

Connection Steps:

  1. Remove insulation sleeve 18-19mm for two conductors.
  2. Insert battery wires according to polarities indicated on the terminal block and tighten the terminal screws. Ensure correct polarity at both the battery and the inverter/charger.
  3. For 8.6KW and 10.6KW models, assemble battery ring terminals and fix two cable glands into positive and negative terminals. Insert the ring terminal flatly into the battery connector and tighten screws with a torque of 5Nm.

⚠ CAUTION!! Do not place anything between the flat part of the inverter terminal and the ring terminal. Otherwise, overheating may occur.

⚠ CAUTION!! Do not apply anti-oxidant substance on the terminals before terminals are connected tightly.

⚠ CAUTION!! Before making the final DC connection or closing DC breaker/disconnector, ensure positive (+) is connected to positive (+) and negative (-) is connected to negative (-).

4.4. AC Input/Output Connection

⚠ CAUTION!! Install a separate AC breaker (recommended 50A) between the inverter and AC input power source. Do NOT mis-connect input and output connectors.

Recommended Cable Requirement for AC Wires:

MODELGaugeTorque Value
6.6KW10 AWG1.2~1.6 Nm
8.6KW/10.6KW8 AWG1.2~1.6 Nm

Connection Steps:

  1. Before making AC input/output connection, open the DC protector or disconnector first.
  2. Remove insulation sleeve 10-11mm.
  3. Insert AC input wires according to polarities (Ground, LINE, Neutral) indicated on the terminal block and tighten the terminal screws.
  4. The inverter is equipped with dual-output (AC output 1 and AC output 2). Insert AC output wires according to polarities and tighten terminal screws.
  5. Ensure all wires are securely connected.

⚠ CAUTION: Important! Be sure to connect AC wires with correct polarity. If L and N wires are connected reversely, it may cause utility short-circuited when these inverters are worked in parallel operation.

⚠ CAUTION: Appliances like air conditioners require 2-3 minutes to restart. Check if your appliance has a time-delay function before installation to prevent damage from power shortages.

4.5. PV Connection

⚠ CAUTION: Install a separate DC circuit breaker between the inverter and PV modules. Switch off the inverter before connecting PV modules to prevent damage.

PV Module Selection Parameters:

  • Open circuit Voltage (Voc) of PV modules must not exceed the max. PV array open circuit voltage of the inverter (500 Vdc).
  • Open circuit Voltage (Voc) of PV modules should be higher than the min. battery voltage.

Solar Charging Mode Specifications:

ParameterValue
Max. PV Array Open Circuit Voltage500 Vdc
PV Array MPPT Voltage Range120~450Vdc
MPP Number2

Connection Steps:

  1. Remove insulation sleeve 10-11 mm for positive and negative conductors.
  2. Check correct polarity of connection cable from PV modules and PV input connectors.
  3. Connect positive pole (+) of connection cable to positive pole (+) of PV input connector. Connect negative pole (-) of connection cable to negative pole (-) of PV input connector.
Dual MPPT Inputs for Flexible and Efficient Power Generation
Figure 7: Diagram illustrating dual MPPT inputs (PV1 and PV2) for flexible and efficient power generation from solar panels.

4.6. Communication Connection

Use the supplied communication cable to connect the inverter and PC. Insert the bundled CD into a computer and follow the on-screen instructions to install the monitoring software.

Serial Connection (RS232): Use a RJ45 cable. PIN assignment: PIN1: TXD, PIN2:RXD, PIN4:12V, PIN8:GND.

BMS Communication: Use a RJ45 cable. It is recommended to purchase a special communication cable if connecting to a Lithium-ion battery.

BMS PIN Assignment:

PINAssignment
PIN 3RS485-B
PIN 5RS485-A
PIN 8GND

For detailed BMS communication installation for specific battery types (LIO-4805/LIO-4810-150A, PYLONTECH, WECO, SOLTARO), refer to Appendix II of the full PDF manual.

4.7. Dry Contact Signal

A dry contact (3A/250VAC) is available on the rear panel to start or stop the generator, configurable via the HMI LCD (Setting -> Generator Settings). Ensure Dry Contact Setting is enabled in LCD settings.

Dry Contact Signal Conditions:

Unit StatusConditionDry contact port: NC & CDry contact port: NO & C
Power OffUnit is off and no output is powered.CloseOpen
Power OnOutput is powered from Utility (Utility available)CloseOpen
Power OnGenerator Settings -> When Battery voltage /SOC < Generator ON voltage/SOCOpenClose
Power OnGenerator Settings -> When Battery voltage /SOC > Generator OFF voltage/SOCCloseOpen

5. Operation

5.1. LCD Display Icons

The inverter features a touchscreen LCD for monitoring and configuration. The main interface displays real-time system status.

10.6KW hybrid inverter & 16kWh battery seamlessly matched
Figure 8: The inverter's smart touch display, showing a clear color LCD touchscreen with an intuitive interface, modern UI design, and real-time display of key parameters like voltage, current, and power.

Main Interface Elements:

  • Top Bar: Displays time, Wi-Fi status, BMS status, and alarm sound.
  • System Settings Icon: Press to enter system settings (general, output, battery, advanced, grid, generator settings).
  • Main Screen: Shows information for inverter, solar, grid/generator, battery, and load. Energy flow is indicated by arrows.
  • "Press to ON" Button: Toggles system on/off and displays inverter serial number, version, and event records.
  • "Event" Button: View alarms and error records.
  • Back Key: Returns to the home screen.

5.2. LCD Settings

Access settings by pressing the system settings icon on the main display. This allows configuration of various parameters.

General Settings:

  • Time Setting: Set system time.
  • LCD Sleep Time: Configurable (always/30 seconds/1 minute/never).
  • Alarm Control: Enable or disable alarms.
  • Overload Bypass: Enable or disable bypass overload.

Output Settings:

  • Output Voltage: 220/230/240 V.
  • Output Frequency: 50/60 Hz.
  • AC Output Mode: Single or parallel mode.
  • Output Source Priority: "SUB" or "SBU".
  • Time Duration for Total AC Output On/Off: Control output 1/2 working time.
  • Time Duration for O/P-2 On/Off: Control output 2 start and end time.
  • Discharging Period for O/P-2: Control output 2 working time.
  • Low DC Cut Off Voltage on O/P-2: Turn off output when battery voltage is below set point.
  • Battery Re-discharging Voltage O/P-2: Turn off output when battery voltage is above set point.

Battery Settings:

  • Battery Type: "Use" for lead-acid, others for lithium battery protocols.
  • Charging Source Priority: Regular (Solar first, solar and Utility, Only solar) or Scheduled.
  • Max (Grid+Solar) Charging Current: 10A to max charging current (10A increments).
  • Max. Utility Charging Current: 2A to max charging current (10A increments).
  • Max. Discharging Current: Set maximum discharge current.
  • CV Voltage: 48.0V to 60.0V (follows BMS for lithium batteries).
  • Floating Voltage: 48.0V to 60.0V (follows BMS for lithium batteries).
  • Activate Lithium BAT When Power On: Enables lithium battery activation.
  • Battery Low Cut Off and Re-discharging Setting: Customize low cut off voltage/SOC and re-discharging voltage/SOC.
  • Max Discharging Current in Hybrid Mode: Sets max battery discharge current when feeding to grid.
  • Time Of Use Setting: Set battery charging and discharging time periods.

Advanced Settings:

  • Password Protected: Default password is 0000.
  • Reset to Default: Restores factory settings.
  • Erase All Data Log: Clears energy generation data.
  • Solar Priority: Sets priority of PV energy.
  • External CT: Enable for Zero Export To CT function.
  • Touch Screen Calibration: Calibrate touch screen sensitivity.
  • Lock All Changes: Locks key settings.
  • Change Admin Password: Change password for Advanced Setting page.

Grid Settings:

  • Wide AC Input: 90-280VAC (APL) or 170-280VAC (UPS).
  • Reverse LED Calibration: Adjusts Grid power.
  • Certification: Shows IEC62116 (not changeable).
  • Feed to Grid: Allows solar energy to feed to the grid.
  • Battery Feed to Grid: Allows battery energy to feed to the grid.
  • Feed to Grid Power Limitation: Set limits (6600W, 8600W, 10600W).

Generator Settings:

  • Generator On Voltage/SOC: Activates generator when battery voltage/SOC is low.
  • Generator Off Voltage/SOC: Stops generator when battery voltage/SOC is high.
  • Generator Charging Setting: Enables generator to charge battery.
  • Dry Contact Setting: Disable (consistent with Power Off state) or Enable (depends on generator ON voltage/SOC).

5.3. Operating Mode Description

The system operates in various modes depending on power availability and configuration. You can check the current operating mode via the LCD.

System Work ModeBehaviorsState Description
Standby modeNo output power, solar or utility charger availableBattery is charged by PV energy. No charging.
Line modeOutput power from utility. Charger is available.Utility charges battery and provides power to load. PV energy, battery power and utility provide power to load. PV energy and utility charge battery, and utility provides power to load. PV energy charges battery, utility and PV energy provide power to the load. PV energy charges battery, PV energy provides power to the load and feeds remaining energy to the grid.
Battery modeOutput power from battery or PVPV energy and battery energy supply power to the load. PV energy charges battery and provides power to the load. Battery provides power to the load.
Only PV modeOutput power from PVPV provides power to the load. No charging.
Fault modeNo output, no charging.Errors caused by internal circuit or external reasons (e.g., over temperature, output short circuit).

6. Specifications

Detailed technical specifications for the PowMr 10.6KW Hybrid Inverter and 16kWh 48V LiFePO4 Battery system.

MODEL6.6KW10.6KW
RATED OUTPUT POWER
Rated Output Power6600W10600W
PV INPUT (DC)
Max. PV Power12000W18000W
Max. PV Array Open Circuit Voltage500 VDC
MPPT Range @ Operating Voltage120 VDC~450 VDC
Max. PV Array Maximum Imp/per MPPT2*21A2*27A
Number of MPPT Tracker2
GRID-TIE OPERATION
GRID OUTPUT (AC)
Nominal Output Voltage220/230/240 VAC
Feed-in Grid Voltage Range195.5~253 VAC @India regulation
184 ~ 264.5 VAC @Germany regulation
184 ~ 264.5 VAC @South America regulation
195.5~253 VAC @ South Africa
182~260 VAC @ Pakistan
Feed-in Grid Frequency Range49~51Hz @India regulation
47.5~51.5Hz @Germany regulation
57~62Hz @South America
47~52Hz @ South Africa
45.1~54.9Hz @ Pakistan
Nominal Output Current28.7A46.1A
Maximum Conversion Efficiency (DC/AC)97%
OFF-GRID, HYBRID OPERATION
GRID INPUT
Acceptable Input Voltage Range90 - 300 VAC or 170 - 300 VAC
Frequency Range50 Hz/60 Hz (Auto sensing)
Transfer Time< 10ms (for UPS)
< 20ms (for home appliances)
< 50ms (for parallel system operation)
Rating of AC Transfer Relay40A60A
GENERATOR INPUT
Acceptable Input Voltage Range90 - 300 VAC
Frequency Range50 Hz/60 Hz (Auto sensing)
Rating of AC Transfer Relay40A60A
BATTERY MODE OUTPUT (AC)
Nominal Output Voltage220/230/240 VAC
Output WaveformPure Sine Wave
Efficiency (DC to AC)93%
BATTERY & CHARGER
Nominal DC Voltage48 VDC
Maximum Charging Current (from Grid)135A210A
Maximum Charging Current (from PV)135A210A
Maximum discharging Current135A210A
GENERAL
Dimension, D X W X H (mm)633 x 418 x 192
Net Weight (kgs)23.529
INTERFACE
Parallel-ableYes
External Safety Box (Optional)Yes
CommunicationUSB or RS232 / RS 485/WIFI
ENVIRONMENT
Humidity0 ~ 95% RH (No condensing)
Operating Temperature-25°C to 50°C

Battery Specifications (POW-LIO48300-IP65):

  • Nominal Energy: 16.18kWh (51.2V, 316Ah)
  • Cells: Grade A LiFePO4
  • Cycle Life: ≥6000 cycles (80% DOD)
  • IP Rating: IP65 (rainproof and dust-tight)
  • BMS: Built-in with 2A active balancing
  • Parallel Connection: Up to 16 batteries (max 258kWh)
  • Design: Floor-standing with heavy-duty casters
  • Max Charge Current: 200A
  • Continuous Discharge Current: 200A
  • Communication Interfaces: RS232, RS485, CAN, dry contact
  • Safety: Built-in DC Breaker, low-voltage switch design

7. Maintenance

Regular maintenance ensures the longevity and optimal performance of your PowMr Hybrid Inverter and Battery system.

  • Periodic Inspection: Regularly check all wiring connections for tightness and signs of wear or corrosion.
  • Cleaning: Keep the inverter and battery surfaces clean and free from dust and debris. Ensure ventilation openings are not blocked.
  • Environmental Check: Verify that the installation environment remains within the specified temperature and humidity ranges.
  • Software Updates: Periodically check for and apply any available firmware updates for the inverter via the i.Solar app to ensure optimal performance and security.
  • Battery Health: Monitor battery performance through the LCD display and i.Solar app. Pay attention to any warnings or fault codes related to battery health.

8. Troubleshooting

This section provides common problems, their possible causes, and solutions. For persistent issues, contact customer support.

8.1. General Troubleshooting

ProblemHMI/BuzzerExplanation / Possible causeWhat to do
Unit shuts down automatically during startup process.HMI and buzzer will be active for 3 seconds and then complete off.The battery voltage is too low (<1.91V/Cell)1. Re-charge battery.
2. Replace battery.
No response after power on.No indication.1. The battery voltage is far too low. (<1.4V/Cell)
2. Battery polarity is connected reversed.
1. Check if batteries and the wiring are connected well.
2. Re-charge battery.
3. Replace battery.
Mains exist but the unit works in battery mode.HMI shows grid voltage is 0VInput protector is trippedCheck if AC breaker is tripped and AC wiring is connected well.
When the unit is turned on, internal relay is switched on and off repeatedly.HMI shows battery voltage is 0VBattery is disconnected.Check if battery wires are connected well.
Overload errorThe inverter is overload 110% and time is up.Reduce the connected load by switching off some equipment.
Output short circuited.Output short circuited.Check if wiring is connected well and remove abnormal load.
Over TemperatureInternal temperature of inverter component is over 100°C.Check whether the air flow of the unit is blocked or whether the ambient temperature is too high.
Battery high voltageBuzzer beeps continuously and HMI show the Fault iconBattery is over-charged. The battery voltage is too high.Return to repair center. Check if spec and quantity of batteries are meet requirements.
FAN lockFan faultReplace the fan.
Output abnormalOutput abnormal (Inverter voltage below than 190Vac or is higher than 260Vac)1. Reduce the connected load.
2. Return to repair center
DC-DC overcurrentDC/DC over current or surge.Restart the unit, if the error happens again, please return to repair center.
Inverter overcurrentOver current or surge.Restart the unit, if the error happens again, please return to repair center.
BUS low voltageBus voltage is too low.Restart the unit, if the error happens again, please return to repair center.
Abnormal output voltageOutput voltage is unbalanced.Restart the unit, if the error happens again, please return to repair center.
Solar high voltageSolar input voltage is more than 550V.Reduce the number of solar panels
Battery LowThe battery voltage is less than 30VCharge the battery voltage to above 30V
Battery overcurrentThe battery is over-dischargedThe discharge current of the battery needs to be reduced

8.2. Parallel Operation Troubleshooting

Fault CodeFault Event DescriptionSolution
60Current feedback into the inverter is detected.1. Restart the inverter.
2. Check if L/N cables are not connected reversely in all inverters.
3. For parallel system in single phase, make sure the sharing cables are connected in all inverters.
4. For supporting three-phase system, make sure the sharing cables are connected in the inverters in the same phase, and disconnected in the inverters in different phases.
5. If the problem remains, please contact your installer.
71The firmware version of each inverter is not the same.1. Update all inverter firmware to the same version.
2. Check the version of each inverter via LCD setting and make sure the CPU versions are same. If not, please contact your installer to provide the firmware to update.
3. After updating, if the problem still remains, please contact your installer.
72The output current of each inverter is different.1. Check if sharing cables are connected well and restart the inverter.
2. If the problem remains, please contact your installer.
80CAN data loss1. Check if communication cables are connected well and restart the inverter.
2. If the problem remains, please contact your installer.
81Host data loss1. Check if communication cables are connected well and restart the inverter.
2. If the problem remains, please contact your installer.
82Synchronization data loss1. Check if communication cables are connected well and restart the inverter.
2. If the problem remains, please contact your installer.
83The battery voltage of each inverter is not the same.1. Make sure all inverters share same groups of batteries together.
2. Remove all loads and disconnect AC input and PV input. Then, check battery voltage of all inverters. If the values from all inverters are close, please check if all battery cables are the same length and same material type. Otherwise, please contact your installer to provide SOP to calibrate battery voltage of each inverter.
3. If the problem still remains, please contact your installer.
84AC input voltage and frequency are detected different.1. Check the utility wiring connection and restart the inverter.
2. Make sure utility starts up at same time. If there are breakers installed between utility and inverters, please be sure all breakers can be turned on AC input at same time.
3. If the problem remains, please contact your installer.
85AC output current unbalance1. Restart the inverter.
2. Remove some excessive loads and re-check load information from LCD of inverters. If the values are different, please check if AC input and output cables are in the same length and material type.
3. If the problem remains, please contact your installer.
86AC output mode setting is different.1. Switch off the inverter and check LCD setting of “AC OUTPUT MODE”.
2. For parallel system in one phase, make sure no 3P1, 3P2 or 3P3 is set.
3. For supporting three-phase system, make sure no “PAL” is set.
87Single Machine exists in parallel system1. Check whether a single machine exists in parallel system.

9. User Tips

Here are some helpful tips for optimizing your PowMr Hybrid Inverter and Battery system:

  • Monitor Regularly: Use the i.Solar app to keep an eye on your system's performance, battery charge, and energy flow. This helps in identifying potential issues early.
  • Optimize Time-of-Use: Configure the "Time Of Use Setting" in the LCD to charge batteries during off-peak electricity hours and discharge during peak hours to save on energy costs.
  • Proper Sizing for Parallel Systems: If expanding with multiple inverters or batteries, ensure all cables (battery, AC input/output, current sharing) are of the same length and material type to prevent voltage differences and ensure stable operation.
  • Secure Connections: Always double-check all electrical connections for tightness and correct polarity to prevent faults and ensure safety.
  • Environmental Awareness: While outdoor-rated, placing the units in a shaded, protected location can extend their lifespan and maintain optimal operating temperatures.

10. Warranty and Support

The PowMr 10.6KW Hybrid Inverter and 16kWh 48V LiFePO4 Battery system typically comes with a 1-year warranty. For any technical support, service, or warranty claims, please contact the manufacturer directly.

Contact Information:

  • Brand: PowMr
  • Email: support@powmr.com
  • Web: www.powmr.com
  • Address: Henggang Street, Longgang District, Shenzhen, Guangdong, China
  • Tel/Fax: +86755-28219903

11. Appendix

11.1. Parallel Function

This inverter supports parallel operation in two modes:

  • Single phase parallel operation with up to 9 units.
  • Three-phase equipment support with up to 9 units (max 7 units per phase).

When installing multiple units, ensure proper spacing for heat dissipation (approx. 20cm to the side, 50cm above and below, 100cm to the front). All battery cables must be of the same length and material. For detailed wiring diagrams and breaker specifications for parallel configurations, refer to Appendix I in the full PDF manual.

⚠ WARNING: When the number of parallel machines exceeds 6, add a magnetic ring to the output L cable. The magnetic ring is found in the inverter's accessory bag.

⚠ WARNING: Do not connect the current sharing cable between inverters in different phases, as this may damage the inverters.

11.2. BMS Communication Installation

For connecting to a lithium battery, a custom-made RJ45 communication cable is recommended. This cable facilitates information exchange between the lithium battery and the inverter, including re-configuring charging voltage/current and battery discharge cut-off voltage, and controlling inverter charging based on battery status.

For detailed pin assignments and specific battery communication configurations (e.g., LIO-4805/LIO-4810-150A, PYLONTECH, WECO, SOLTARO), refer to Appendix II in the full PDF manual.

11.3. Wi-Fi Operation Guide

The built-in Wi-Fi module enables wireless communication with the monitoring platform, allowing remote monitoring and control via the i.Solar APP (available for iOS 12.0+ and Android 10.0+).

Key Functions of i.Solar App:

  • Daily data monitoring of the inverter.
  • Querying real-time data.
  • Sending commands to the device.
  • Remote operation of the device.

Wi-Fi Model Setting:

  1. Turn on your mobile device and open Wi-Fi settings.
  2. Connect to the Wi-Fi network starting with "FC41D_" (default password: 12345678).
  3. Open the i.Solar App, log in, and navigate to "Network Config" to enter your home router's Wi-Fi name (STA SSID) and password (STA Password).
  4. Save the settings.

For detailed instructions on app usage, login, home page features, real-time data, parameter settings, and OTA firmware updates, refer to Appendix III in the full PDF manual.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.