AVATTO GW90-POE-Ti

Contents

AVATTO ZigBee PoE Dongle Plus GW90-POE-Ti User Manual

High-Performance Chipset Dual-antenna Ethernet, Wi-Fi, USB Connection for Home Assistant, Zigbee2MQTT

1. Introduction

The AVATTO ZigBee 3.0 PoE Dongle (Model: GW90-POE-Ti) is a versatile ZigBee gateway designed to connect ZigBee sub-devices with open-source platforms such as Home Assistant and Zigbee2MQTT. It features a high-performance ESP32+CC2652P chipset and supports multiple connectivity options including Power over Ethernet (PoE), Wi-Fi, and USB. The device allows for flexible deployment and management through a web console, enabling firmware updates and mode switching. Advanced functionalities like Webhook, MQTT, and VPN are also integrated.

AVATTO ZigBee PoE Dongle with Home Assistant and Zigbee2MQTT logos
AVATTO ZigBee PoE Dongle Plus GW90-POE-Ti
Diagram showing high-performance chips, 5dBi antenna gain, adjustable antenna, PoE power, and firmware burning via web interface
Key Features: High-performance chips (ESP32, CC2652P), 5dBi antenna gain, adjustable antennas, PoE power, and web-based firmware updates.

2. Package Contents

Please check the package for the following items:

  • AVATTO ZigBee PoE Dongle Plus (GW90-POE-Ti)
  • Two 5dBi Antennas
  • USB Type-C Cable
  • Mounting Bracket
  • Screws and Screw Anchors
  • Double-sided Tape
  • User Manual (Printed Quick Start Guide)
Contents of the AVATTO ZigBee PoE Dongle package
Included items in the product package.

3. Setup Guide

3.1 Antenna Installation

Attach the two included 5dBi antennas to the designated ports on the dongle. The antennas are rotatable 360 degrees and can be adjusted 90 degrees for optimal signal coverage.

3.2 Device Installation

The dongle can be installed in two ways:

  1. **Desktop Placement**: Use the provided double-sided tape to fix the device securely to a desktop or flat surface.
  2. **Wall Mounting**: Use the included screws and screw anchors to secure the mounting bracket to a wall, then slide the device onto the bracket.

3.3 Power Supply Options

The AVATTO ZigBee PoE Dongle supports two power supply methods:

  • PoE (Power over Ethernet): Connect an Ethernet cable from a PoE-enabled router or switch to the dongle's RJ45 port. This provides both power and network connectivity. If your router or switch does not support PoE, you will need to purchase a separate PoE power supply module.

    Note: The PoE port requires 48V-0.25A input.

  • Type-C USB: If PoE is not available or preferred, use the included Type-C USB cable to connect the dongle to a 5V-1A USB power adapter (not included) or a compatible USB port for power.

    Note: The Type-C port requires 5V-1A input.

3.4 Network Connection Methods

The dongle offers multiple ways to connect to your network:

  • Ethernet Connection (PoE powered): Connect a network cable to the RJ45 port for a stable and reliable wired network signal. This can also provide power if using PoE.
  • Wi-Fi Connection: The device can connect wirelessly to your home Wi-Fi network, allowing flexible placement anywhere within your home's Wi-Fi range.
  • USB Connection: Use the included Type-C USB cable to connect the device directly to a computer's USB port or a Home Assistant Box, functioning as a USB Dongle.
Illustrations of Ethernet, WiFi, and USB connection methods for the dongle
Multiple network connection methods: Ethernet (PoE powered), Wi-Fi, and USB.

4. Operating Instructions

4.1 Accessing the Web Console

Once the device is connected to your network (via Ethernet or Wi-Fi), you can access its web console for configuration and management:

  1. Ensure your computer or mobile device is on the same local area network (LAN) as the dongle.
  2. Open a web browser.
  3. In the address bar, enter avatto-gw90-ti.local and press Enter.
  4. For the first access, you will be prompted to set a password. Follow the on-screen instructions.
  5. Once logged in, you can configure the dongle for ZHA (Zigbee Home Automation) or Z2M (Zigbee2MQTT) and perform firmware updates.
Screenshot of the web console interface for computer and mobile phone control
Web console interface for device control and configuration.

4.2 Firmware Updates

Firmware updates for the ZigBee Coordinator/Router are performed directly through the web interface (http://AVATTO-GW90-TI.local). A stable Wi-Fi or Ethernet connection is required during the update process.

4.3 Supported Platforms

The AVATTO GW90-POE-Ti is designed to integrate seamlessly with popular open-source smart home platforms:

  • Home Assistant
  • Zigbee2MQTT
  • OpenHAB (via Home Assistant integration)
Diagram showing compatibility with Home Assistant Green, Yellow, Rasp Pi, AVATTO HA80, HA70
Compatibility with various Home Assistant devices and Raspberry Pi.
Application scenarios showing the dongle connecting to various Zigbee devices
The dongle can connect to a wide range of Zigbee devices, including switches, thermostats, and sensors.

5. Maintenance

To ensure optimal performance and longevity of your AVATTO ZigBee PoE Dongle, please observe the following:

  • **Ventilation**: Do not obstruct the ventilation of the device by covering it with items such as newspapers, tablecloths, or curtains. Proper airflow is essential to prevent overheating.
  • **Heat Sources**: Do not place naked flame sources, such as candles, on or near the appliance.
  • **Cleaning**: Use a soft, dry cloth to clean the device. Avoid using liquid cleaners or aerosols.
  • **Firmware**: Regularly check for and install firmware updates via the web console to benefit from new features and security enhancements.

6. Troubleshooting

  • Device not powering on: Ensure the power supply is correctly connected. If using PoE, verify that your router/switch is PoE-enabled or that a separate PoE power supply module is in use. If using Type-C, ensure the power adapter provides 5V-1A.
  • Cannot access web console: Verify that the device is connected to the network (Ethernet or Wi-Fi) and that your computer is on the same LAN. Double-check the URL avatto-gw90-ti.local for typos.
  • ZigBee devices not connecting: Ensure the dongle's firmware is up to date. Check the dongle's web console for ZigBee network status and ensure devices are in pairing mode.
  • Poor signal strength: Adjust the position and angle of the dual antennas for better signal coverage. Ensure the dongle is not placed near large metal objects or other sources of interference.

If you encounter any persistent issues, please refer to the detailed user manual available online or contact customer support.

7. Specifications

Feature Detail
Model Number GW90-POE-Ti
Chipset ESP32 (Wi-Fi) + CC2652P (ZigBee)
CPU 240MHz
Memory 16MB
Antenna Dual 5dBi, 360° rotation capability
Communication Distance Up to 200 meters (open space)
Network Interface RJ45 (Gigabit Ethernet)
Power Input (Type-C) 5V-1A
Power Input (PoE) 48V-0.25A
Working Temperature -10°C to 60°C
Dimensions (L x W x H) 157mm x 45mm x 131mm
Supported Platforms Home Assistant, Zigbee2MQTT
Certification CE
EU LVD Voltage Below 50Vac or 75Vdc
Diagram showing product dimensions and port layout
Product dimensions and port overview.

8. Warranty and Support

The AVATTO ZigBee PoE Dongle Plus GW90-POE-Ti comes with a 1-year warranty from the store of purchase.

8.1 Customer Support

If you encounter any issues or have questions regarding your device, please contact the store's customer service. A professional support team is available to assist you.

8.2 Online Resources

For the most up-to-date user manual, firmware files, and detailed setup instructions, please visit the official AVATTO website:

  • Official Website: https://www.avattosmart.com
  • To access the product manual and firmware files for the GW90-POE-Ti:
    1. Visit https://www.avattosmart.com
    2. Navigate to Home Assistant → Dongle and locate the GW90-POE-Ti model.
    3. Click "Learn More", then scroll to the bottom of the page.
    4. Select "Enter" under Technical Support to view setup instructions and download firmware/updates.

A PDF version of the user manual is also available for download at the official website, for example: GW90-POE-Ti User Manual (PDF).

9. Safety Information

Please read and adhere to the following safety warnings:

  • This product is not a toy and is not intended for use by children. For adult use only.
  • The appliance is suitable for moderate climates only.
  • Ensure proper ventilation. Do not impair ventilation by covering the appliance with items such as newspapers, tablecloths, curtains, etc.
  • Do not place naked flame sources, such as candles, on the appliance.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.