ABIR WD10 Window Cleaning Robot Instruction Manual

Introduction

Thank you for choosing the ABIR WD10 Window Cleaning Robot. This manual provides essential information for the safe and efficient operation, maintenance, and troubleshooting of your device. Please read it carefully before use and keep it for future reference.

A detailed user manual in PDF format is available for download here.

Safety Specifications

When using the product, please be always vigilant and follow these instructions!

Please read this instruction manual carefully before using the product! Please save the instruction manual!

• The product cannot be used by children under the age of 8 or by persons with physical or mental disabilities. If necessary, please do it under the supervision and guidance of a guardian. Do not allow children to come near products that are in working condition or play with them as toys.
• Do not use this product in extreme environments (temperatures below 0°C and temperatures above 40°C).
• Please keep the product in a powered state at all times while the product is working. The built-in safety backup battery of the product is only used to maintain the product in the event of a sudden power failure, keep adsorbed on the glass for a limited time and not fall, and must not be used as normal power supply, so as not to bring risks.
• During the use of this product, please ensure that someone is there to watch over and help the product if necessary. While the robot is working, remove valuables from under the robot and make sure that any animals do not stand under the working robot.
• Use only in home environment and indoor environment, do not use in commercial and industrial places.
• Do not use this product on glass that has broken holes, bumps and all kind of stickers to avoid risks or drop out.
• Use this product as directed in the instruction manual, using only accessories recommended or sold by the manufacturer; only applicable to original rechargeable batteries and adapters supplied by the manufacturer.
• Make sure that the supply voltage matches the voltage indicated on the adapter.
• Make sure to use this product on glass with a glass thickness more than 5mm.
• Do not use on large areas of wet or oily glass to avoid the risk of slipping and falling of the product.
• Keep products away from heat sources or flammable materials.
• It is forbidden to use this product when the product is not completely adsorbed or there is obvious damage.
• Do not place this product in water or other liquids to reduce the risk of electric shock; do not store this product where it may be dropped or pulled into the tub or sink.
• Do not touch the plug or product with wet hands.
• Battery charging should not be carried out in an overheated or cold environment, which may affect the service life of the battery.
• The product cannot be used when the adapter is not powered to the adapter.
• It is forbidden to put the robot on household appliances, wet or in the place with a fire source for charging, so as not to cause unnecessary losses.
• Please use the power cord carefully to avoid damage, and do not use the power cord to drag, lift the product or use the cord as a handle. It is forbidden to close the glass window to clamp the power cord or place items on the power cord during use, and the power cord should be kept away from the heat source.
• Do not use this product with a damaged power cord or power outlet. Do not use the product when it does not work properly due to dropping, damage or water ingress, to avoid injury, the product should be repaired by the manufacturer or its after-sales service department.
• If the power cord is damaged, it must be replaced by a professional from the manufacturer, its maintenance department or similar department in order to avoid danger.
• The plug must be unplugged from the electrical outlet before maintaining or cleaning the product, but do not pull the power plug from the outlet by pulling the power cord.
• The battery must be replaced by a professional from the manufacturer, its maintenance department or similar department.
• Before the product is scrapped, the battery must be removed and scrapped in accordance with local laws and regulations and environmental protection regulations.
• If you need to scrap this product, please disconnect the power to the product before removing the battery from the product.
• Dispose of used batteries in accordance with local laws and regulations and environmental regulations.
• Incineration of the product is prohibited even if it has been severely damaged, as the battery of the product may cause an explosion.
• Please use the product as directed in this manual. The Company shall not be liable for any loss or injury caused by improper use.
• It is strictly forbidden to use this product by children, mentally handicapped persons or people who lack common sense and experience in using home appliances without the guidance of a dedicated person.
• While the robot is working, supervise the child's behavior to ensure that the product is not being played.
• Children are strictly prohibited from playing with the product.
• It is strictly forbidden for children to clean, operate and maintain the product without supervision.

Product Composition

Package Contents

• Host
• Clean Cloth *4pcs
• Roller Brush *2pcs (install on robot)
• Adapter+Power Cord
• Extension Cord+Safety Rope
• Remote Control
• Adding Water Bottle
• Corner Brush *8pcs (4pcs on robot, 4pcs in the box)
• User Manual

Product Parts Diagram

• Top Side: Water spray port, Water tank injecting port, Power key & LED light, Speech window, The handle.
• Bottom Side: Water spray port, Cleaning cloth, Main motor, Rolling brush, Anti-drop sensor, Drive wheel unit.
• Connectivity: Safety rope, DC power jack.

Setup Instructions

Precautions Before Use

• It is strictly forbidden to use this product on framed glass with a frame thickness (height difference from the glass surface to the frame surface) < 5mm.
• Please use this product on framed glass with an area ≥ 50*70cm.
• Connect the adapter. If the red and blue lights flash alternately, the robot is in the charging state. Make sure that it is charged until the blue light is solid (about 1 hour). The product cannot perform cleaning work when the red light flashes.
• If there is too much dust on the glass surface, please wipe out a clean area for the product to adsorb.
• When there are immovable obstacles (such as guardrails, furniture, etc.) in front of the window, this product can only be used when the distance between the window and the obstacle is more than 8.5 cm.
• The product does not work on horizontal glass surfaces.
• If you use this product on a window that is not completely vertical, there is a possibility that the product may not operate properly. Please make sure that someone is there to watch over and help the product if necessary.
• This product cannot be used upside down.

Step-by-Step Setup

1. Install the cleaning cloth: Fully wet the cleaning cloth in water and wring it out as much as possible by hand. Align the cloth and stick it inside the adsorption plate at the bottom of the product.
2. Connect the adapter: Connect the adapter plug to a power outlet.
3. Assemble safety rope: When wiping glass, secure the product with the safety rope to improve safety.
4. Install the safety buckle: When wiping glass, the safety rope needs to be secured elsewhere in the room. When using the product to wipe the outside of the glass, close the window so that the gap between the window is slightly larger than the diameter of the safety rope.
5. Add water or glass water: Open the water tank injecting port and add water or glass cleaner. Do not add liquid soap or dishwashing liquid.
6. Connect to power and turn on: Connect the DC end of the adapter to the robot. The robot's blue light will be continuously on.
7. Start the robot: Short press the power button. The blue light will flash, and the fan will start to work. Do not place the fan near small objects like hair to avoid blocking.
8. Adsorption: Place the product more than 10cm away from the glass frame, and wait for the blue light to turn on and for successful adsorption.

Operating Instructions

Remote Control Functions

Cleaning Modes

• Auto Cleaning Mode: Adaptive Z/N cleaning route – selects the most efficient path based on window size, cleans faster.
• N Cleaning Mode: Robot starts with a 'Z' path, regular wipe for 1 time.
• Z Cleaning Mode: Wipe with 'N' cleaning Path, regular wipe for 1 time.
• Fixed-point Mode: Robot will wipe back and forth repeatedly with water spray in one area.
• Edge Cleaning Mode: Cleans along the edge of glass, actively targets and deep-cleans window edges.

App Control

The ABIR WD10 can be controlled via a remote control or the Tuya Smart / Smart Life APP. To use the app:

1. Download the App: Open the Bluetooth function on your mobile phone. Search for "Tuya Smart APP" or "Smart Life APP" in your App Store or Google Play. Alternatively, scan the QR codes below to download and install.

2. Register and Connect: Register an account and set a password. The first time you connect, the machine needs to be connected to the adapter for power. Then, press the "Start/Pause" button on the remote control 3 times. The blue light on the machine will flash red to complete the operation. If the device is not found, quickly press the "Start/Pause" button 3 times in a row to restore factory settings, then click "Add Device" again.

Product Demonstration Video

Maintenance

Cleaning the Cleaning Cloth

• Remove the cleaning cloth, soak in water at about 20°C for 2 minutes, then gently hand wash and dry before use.
• Do not use the cleaning cloth directly after washing to avoid slipping during use.
• Good maintenance is conducive to prolonging the service life of the cleaning cloth. When the cloth is too old to stick to the adsorption plate at the bottom, replace it in time to achieve the best cleaning effect.

Cleaning the Wheels

• Connect the adapter. The machine's blue light will remain on constantly.
• Press the "Bottom drive track cleaning" key on the remote control. The wheels will rotate.
• Wipe the wheel skin with a cloth and cleaning solution.
• Press the "Bottom drive track cleaning" key again on the remote control. The wheels will stop rotating.
• The wheels are easy to stick to dust and water during the use of the robot and cause slippage, please clean the wheels in time.

Roller Brush Disassembly and Mounting

• Disassembly: Push the roller button downwards, then lift the roller upwards to remove the roller brush.
• Mounting: Use a roller brush to lift the end with the roller brush motor installed, then put it in and rotate it to the bottom. After assembly, press the roller brush down and rotate it until a "click" sound is heard, indicating that the roller brush is complete. Ensure that the shaft on the roller brush is installed into the bearing on the machine.

Troubleshooting

Indicator Light and Sound Description

Common Issues and Solutions

Technical Specifications

Warranty and Support

Our warranty is 3 years. If any problem happens to the robot, you can contact us and send video to show the situation, then we will send free spare parts for your replacement. If out of warranty, we will still support you.

User Tips

• The dual roller system is very effective at wiping away marks.
• Corners are cleaned well, but may not be perfect.
• One deep-clean cycle takes about 18 minutes. For outside glass, two cycles are recommended for better results.
• Minimal light streaks can be easily wiped off manually after the robot finishes.
• While the robot saves effort, it might not always be faster than manual cleaning for all window types.
• The robot adheres very well to glass, providing strong suction.
• The robot can be a bit noisy due to strong suction and rubber track friction, but this is normal and does not indicate a fault.

Frequently Asked Questions

Q: What is the smallest window that the robot can clean?

A: The ABIR WD10 is designed for framed glass surfaces with a minimum area of 50x70cm (approximately 19.7x27.6 inches). It is not suitable for framed glass with a frame thickness (height difference from the glass surface to the frame surface) less than 5mm.