1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your DKD 061-TFT CAN One-LIN Speedometer Display Dashboard. Designed for scooters, bikes, and mopeds, this display offers essential vehicle information in a clear, digital format. Please read this manual thoroughly before installation and use to ensure proper function and safety.
2. Safety Information
- Always disconnect the vehicle's power source before attempting any installation or wiring.
- Ensure all connections are secure and properly insulated to prevent short circuits.
- Do not attempt to modify the device. Unauthorized modifications may void the warranty and pose safety risks.
- Keep the display clean and free from obstructions to ensure clear visibility.
- This device is rated IP67 for protection against dust and water ingress, but avoid prolonged submersion or high-pressure water jets.
3. Product Overview
The DKD 061-TFT Speedometer features a vibrant TFT display providing real-time data. Key indicators include speed, battery charge, voltage, trip distance, and total odometer reading.

The rear of the unit includes mounting points and the main connector port for electrical connections.

4. Setup
4.1. Mounting
The speedometer is designed for dashboard integration. Use the provided mounting points on the rear of the unit to secure it firmly to your vehicle's dashboard. Refer to the dimensional drawing for precise measurements.

4.2. Wiring Diagram
Carefully follow the wiring diagram below to connect the speedometer to your vehicle's electrical system. Ensure each wire is connected to its corresponding function to prevent damage to the device or vehicle.

| Wire Color | Function |
|---|---|
| Green | GND (Ground) |
| White | CANL (CAN Low) |
| Brown | PINK (Signal) |
| Black | CANH (CAN High) |
| +12V | Headlight Dipped Light |
| Orange | Turning Left Signal |
| PINK | Light Blue (Signal) |
| ONE-LIN | Turning Right Signal |
| Blue | Red Yellow (Signal) |
5. Operating Instructions
5.1. Power On/Off
The display will power on automatically when the vehicle's ignition is turned on and power is supplied to the +12V line. It will power off when the ignition is turned off.
5.2. Display Readings
- Battery Indicator: Shows the current battery charge level as a percentage and voltage (e.g., 86.2V).
- Speed: Displays current speed in kilometers per hour (km/h).
- TRIP: Shows the distance traveled for the current trip (resettable).
- ODO: Displays the total accumulated distance traveled by the vehicle (odometer).
- Turn Signals: Indicators for left and right turn signals will illuminate when active.
- Headlight Indicator: Illuminates when the dipped headlight is active.
5.2. Adjustments (if applicable)
Specific button functions for resetting trip distance or changing units (e.g., km/h to mph) are not detailed in the provided information. If your model includes physical buttons, refer to any on-screen prompts or experiment with short/long presses to access settings. Typically, a short press might cycle through display modes, while a long press might reset trip data.
6. Maintenance
6.1. Cleaning
Wipe the display screen with a soft, damp cloth. Do not use abrasive cleaners, solvents, or chemical sprays, as these can damage the screen surface. Ensure no liquid enters the unit.
6.2. Environmental Conditions
The device is designed for outdoor use with an IP67 protection rating. However, extreme temperatures or prolonged exposure to direct sunlight may affect its lifespan and performance. Store the vehicle in a sheltered area when not in use.
6.3. Storage
If the vehicle is to be stored for an extended period, ensure the speedometer is clean and dry. Disconnecting the battery may be advisable to prevent any parasitic drain.
7. Troubleshooting
- Display not turning on: Check all wiring connections, especially the +12V and GND lines. Ensure the vehicle's ignition is on and the battery has sufficient charge.
- Incorrect speed reading: Verify the speed sensor connection and ensure it is functioning correctly. Calibration may be required if the vehicle's wheel size has been changed (if the unit supports calibration).
- No CAN data: Check CANL and CANH connections. Ensure the CAN bus is active and transmitting data.
- Intermittent display: Check for loose connections or damaged wiring. Ensure the power supply is stable.
8. Specifications
| Feature | Detail |
|---|---|
| Model Number | 061 Speedmeter |
| Brand Name | TFT 4.3inch (Display Type) |
| Size (Length x Width) | 162.5mm x 93.7mm |
| DIY Supplies | Electrical |
| Protection Rating | IP67 |
| Smart Type | Electronic |
| Certification | NONE |
| Origin | Mainland China (Shanghai) |
| Package Weight | 2.0 kg |
| Package Dimensions (L x W x H) | 30cm x 30cm x 30cm |
9. User Tips
- For optimal visibility, ensure the display is mounted at an angle that minimizes glare from sunlight.
- Regularly check wiring connections for corrosion or looseness, especially after riding in wet conditions.
- If the display shows unusual readings, first check the vehicle's battery voltage and connections before assuming a device malfunction.
10. Warranty and Support
For any technical assistance, troubleshooting beyond this manual, or warranty inquiries, please contact the seller or manufacturer directly. Keep your purchase records for reference.