Introduction
This manual provides comprehensive instructions for the installation, operation, maintenance, and troubleshooting of your AnyTone AT-6666PRO 80W AM/FM/SSB 10m Band Radio. Please read this manual thoroughly before operating the device to ensure safe and optimal performance.

Safety Information
Always observe the following safety precautions to prevent fire, injury, or damage to the radio:
- Do not operate the radio in explosive atmospheres (e.g., flammable gases, dust particles, metallic powders).
- Do not transmit without an antenna connected.
- Ensure proper ventilation around the radio to prevent overheating.
- Use only the specified power supply (DC 13.8V).
- Keep the radio away from water and moisture.
- Do not attempt to open or modify the radio. Refer all servicing to qualified personnel.
Package Contents
Verify that all items are present in your package:
- AnyTone AT-6666PRO 10m Band Radio
- Microphone with coiled cable and 6-pin connector
- DC Power Cable
- Mounting Bracket and Hardware
- User Manual (this document)



Setup
1. Mounting the Radio
The AT-6666PRO can be mounted in a vehicle or as a base station. Use the provided mounting bracket and hardware to secure the radio in a stable location, ensuring adequate ventilation around the heat sink.
2. Antenna Connection
Connect a suitable 10m band antenna to the SO-239 connector on the rear panel of the radio. Ensure the antenna system has a low SWR (Standing Wave Ratio) to prevent damage to the transceiver.

3. Power Connection
Connect the supplied DC power cable to the radio's power input. Ensure the red wire connects to the positive (+) terminal and the black wire to the negative (-) terminal of a 13.8V DC power source. The power cable includes inline fuse holders for protection. Do not reverse polarity.
4. Microphone Connection
Plug the 6-pin microphone connector into the microphone jack on the front panel of the radio.
Operating Instructions
1. Power On/Off
Press the PWR knob to turn the radio on or off. The display will illuminate, showing the current frequency and operating mode.
2. Volume and Squelch Control
- VOL (Volume): Rotate the outer ring of the PWR knob to adjust the audio output level.
- SQL (Squelch): Rotate the inner part of the PWR knob to set the squelch level. Adjust until background noise is suppressed, but weak signals can still be heard.
3. Frequency and Channel Selection
- Channel Knob (CH): Rotate the large knob on the right to change operating channels.
- Frequency Adjustment: Use the VFO/Channel knob to fine-tune the frequency within the selected channel or band.
4. Mode Selection (AM/FM/SSB)
Press the MODE button to cycle through available modulation modes: AM (Amplitude Modulation), FM (Frequency Modulation), and SSB (Single Sideband - LSB/USB).
5. Transmitting
Before transmitting, ensure an antenna is properly connected and tuned. Press and hold the PTT (Push-To-Talk) button on the microphone to transmit. Release to receive.
6. Other Functions
- DIM: Adjusts display brightness.
- NB/ANL: Noise Blanker / Automatic Noise Limiter for reducing impulse noise.
- TSQ: Tone Squelch (CTCSS/DCS) for selective calling.
- SCAN: Initiates channel scanning.
- ECHO: Activates echo function.
- EMG: Emergency channel access.
Maintenance
- Cleaning: Use a soft, dry cloth to clean the radio's exterior. Do not use abrasive cleaners or solvents.
- Connections: Regularly check all cable connections (antenna, power, microphone) for secure fit and signs of wear.
- Ventilation: Ensure the heat sink fins on the rear of the radio are free from dust and obstructions to maintain proper cooling.
- Fuse Replacement: If the radio does not power on, check the inline fuses on the DC power cable. Replace with fuses of the same rating only.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Radio does not power on. | No power, blown fuse, incorrect wiring. | Check power cable connections, verify power source, replace fuses if necessary. |
| No reception or poor reception. | Antenna not connected, antenna fault, squelch too high. | Check antenna connection, inspect antenna, reduce squelch level. |
| Cannot transmit. | Microphone not connected, PTT button fault, antenna issue. | Ensure microphone is connected, check PTT button, verify antenna connection and SWR. |
| Distorted audio. | Volume too high, external interference, faulty speaker. | Adjust volume, check for interference sources, try external speaker. |
Specifications
| Feature | Detail |
|---|---|
| Model | AT-6666PRO |
| Frequency Band | 10m Band (27MHz SSB) |
| Frequency Range (as listed) | 615-30.105 MHz (Note: Typical 10m band operation is 28.000-29.700 MHz) |
| Modulation Modes | AM, FM, SSB (LSB/USB) |
| Power Output | 80W |
| Power Supply | DC 13.8V |
| Dimensions (W x H x D) | 158mm x 48mm x 250mm |
| Weight | 3.0 kg |
| Origin | Mainland China |

User Tips
- For optimal SSB performance, ensure your antenna is well-tuned and stable.
- Experiment with the NB/ANL settings to find the best noise reduction for your operating environment.
- Always start with the volume low and gradually increase it to a comfortable listening level.
Warranty and Support
For warranty claims, technical support, or service inquiries, please contact your authorized AnyTone dealer or the point of purchase. Keep your purchase receipt as proof of purchase.
Do not attempt to repair the unit yourself, as this may void your warranty.