1. Product Overview
Thank you for choosing the HXCONTROLLER MPPT Solar Charge Controller. This device is designed for solar off-grid power generation systems, automatically managing battery charging and discharging. It incorporates advanced Maximum Power Point Tracking (MPPT) technology to maximize the power harvested from solar panels, ensuring efficient charging and extended battery life.
The controller features a comprehensive self-test function and electronic protection mechanisms to prevent damage from installation errors or system failures. Its user-friendly design makes operation straightforward, but careful reading of this manual is essential to fully utilize its capabilities and optimize your photovoltaic system.
Key Features:
- High Efficiency: Innovative MPPT technology significantly improves solar energy utilization, with a conversion efficiency of up to 97%.
- Fast Tracking: Rapidly scans the entire I-V curve to efficiently track the maximum power point.
- Battery Compatibility: Supports multiple battery types including Lead-acid (sealed, colloidal, open), Lithium-ion (LiFePO4, Li-ion), and user-defined settings. Compatible with 12V/24V/36V/48V/60V/72V/84V/96V systems.
- Comprehensive Protection: Includes automatic protection against overcharge, overdischarge, overload, and short circuit.
- RS485 Communication: Features an RS485 communication interface for multi-machine communication, allowing convenient monitoring of operating parameters.
Why a Solar Charge Controller is Essential:
- Prevents Overcharging: Stops charging once the battery is full, preventing overheating, swelling, or damage.
- Stops Reverse Current: Blocks electricity from flowing back to the solar panel at night, preventing power waste.
- Protects Devices: Stabilizes voltage and current to protect connected lights, appliances, and electronic equipment from unstable power.
- Extends Battery Life: Proper charging and discharging management significantly increases the service life of all rechargeable battery types.
- Improves Charging Efficiency: MPPT controllers optimize power harvesting, especially in varying light conditions, making the system more efficient.
2. Setup and Installation
2.1 Safety Precautions
This manual is intended for installers and operators. Before installation and operation, please read these instructions carefully and keep them in a safe place for future reference.
2.2 Installation Safety Distance
Observe the following safety clearances to ensure adequate heat dissipation and prevent interference with other equipment or objects:
| Direction | Safe Distance |
|---|---|
| Left and Right | 20 cm |
| Up | 30 cm |
| Down | 30 cm |
2.3 Line Connection Method
Follow the correct wiring sequence to connect the solar controller:
- First, connect the positive (+) and negative (-) poles of the battery.
- Next, connect the positive (+) and negative (-) poles of the DC load.
- Finally, connect the positive (+) and negative (-) poles of the solar panel.
Terminal Descriptions:
- 1. Temperature sensor interface: For connecting the external temperature sensor.
- 2. Solar panels: Connect to the positive and negative poles of your solar array.
- 3. Battery: Connect to the positive and negative poles of your battery bank.
- 4. DC load: Connect to your DC loads.
- 5. RS485 interface: For communication with external devices. The RJ12 interface enables communication via RS485 to retrieve MPPT data. Connect wires according to the labelled A-B markings.
- 6. Terminal box cover plate: Protective cover for wiring terminals.
- 7. LCD display: High-definition display for monitoring system status and parameters.
- 8. Cooling hole: Ensures proper ventilation and heat dissipation.
3. Operating Instructions
3.1 Key Operation
| No. | Name | Function |
|---|---|---|
| 1 | Solar panel indicator | Indicates solar panel activity. |
| 2 | Charging indicator | Indicates battery charging status. |
| 3 | DC load indicator | Indicates DC load status. |
| 4 | Warning indicator | Flashes for alarms or errors. |
| 5 | SET / Back button | Enters menu, navigates back. |
| 6 | UP button | Scrolls up, increases value. |
| 7 | DOWN button | Scrolls down, decreases value. |
| 8 | CONFIRM (3s) button | Confirms selection (press for 3 seconds). |
3.2 LCD Main Interface Description
The LCD display provides real-time information about your solar system. The default main interface shows:
- PV Voltage: Solar panel input voltage.
- Controller Generation Wattage: Current power being generated by the controller.
- Charging Current: Current flowing into the battery.
- Battery Voltage: Current battery voltage.
- Total Power Generation: Accumulated energy generated (in kWh).
- System Status: Indicates charging status (e.g., Float Charge).
3.3 Parameter Setting Steps
From the default main interface, press the SET button to enter the main menu. Use the DOWN or UP buttons to navigate through the submenu options.
- Language Setting: Select between Chinese and English.
- DC Output Setting: Toggle the DC load output ON or OFF.
- Battery Type Setting: Choose from pre-set battery types (Lead Acid, Gel, LiFePO4, Li-ion) or define a custom battery type. After selecting, you can set the required voltage parameters.
- Charging Current Setting: Adjust the charging current. The available range depends on the specific product model (refer to the Technical Data Sheet).
- Restore Factory Settings: Select this option to clear all recorded data and restore the controller to its default factory settings.
4. Maintenance
- Regular Inspection: Periodically check all wiring connections for tightness and corrosion. Ensure the controller's cooling holes are free from dust and debris to maintain optimal heat dissipation.
- Environmental Conditions: Ensure the controller operates within its specified working environment temperature range (-20°C to +40°C) and humidity (0-90% RH, non-condensing).
- Temperature Compensation: The controller automatically compensates charging voltage and current based on battery temperature, which helps prolong battery life. Ensure the temperature sensor is correctly installed and functioning.
- Firmware Updates: Check the manufacturer's website periodically for any available firmware updates that may improve performance or add features.
- Cleaning: Keep the LCD screen and buttons clean using a soft, dry cloth. Avoid using abrasive cleaners or solvents.
5. Troubleshooting
The HXCONTROLLER MPPT Solar Charge Controller is equipped with multiple protection functions to ensure safe and reliable operation. If an issue occurs, check the following:
Protection Functions:
- Photovoltaic Array Short-Circuit Protection: Prevents damage from short circuits in the solar panel array.
- Over-Voltage Protection: Protects the system from excessive voltage from the solar panels.
- Over-Current Protection: Safeguards against excessive current flow.
- Reverse Connection Protection: Prevents damage if solar panels or battery are connected with reverse polarity.
- Battery Overcharge Protection: Stops charging when the battery reaches its full capacity.
- Under-Voltage Protection: Disconnects the load to prevent battery over-discharge.
- High-Temperature Protection: Reduces power output or shuts down if the internal temperature exceeds 80°C. The automatic fan cooling system helps manage internal temperatures.
- Open-Circuit Protection: Protects against open circuits in the system.
- Self-Recovery: Many protection features allow the controller to automatically recover once the fault condition is resolved.
If the warning indicator is active, refer to the LCD display for error codes or messages. If the problem persists after checking connections and ensuring no fault conditions are present, consult the Technical Data Sheet or contact support.
6. Specifications
The following table details the technical specifications for the HXCONTROLLER MPPT Solar Charge Controller:
| Feature | 30A/40A Model | 50A/60A Model | 100A/120A Model | |
|---|---|---|---|---|
| Rated Charging Current | 30A/40A | 50A/60A | 100A/120A | |
| Maximum PV Input Power | 12V System | 360W | 600W | 1200W |
| 24V System | 720W | 1200W | 2400W | |
| 36V System | 1080W | 1800W | 3600W | |
| 48V System | 1440W | 2400W | 4800W | |
| 60V System | 1800W | 3000W | 6000W | |
| 72V System | 2160W | 3600W | 7200W | |
| 84V System | 2520W | 4200W | 8400W | |
| 96V System | 2880W | 4800W | 9600W | |
| Charging Mode | MPPT automatic maximum power tracking | |||
| Charging Method | MPPT tracks maximum power, fast charge, balanced charge, and float charge. | |||
| Battery Type | Lead Acid Battery | (12V/24V/36V/48V/96V Auto + Adjustable 12V/24V/36V/48V/60V/72V/84V/96V) | ||
| Gel Battery | 12V/24V/36V/48V/60V/72V/84V/96V adjustable | |||
| Lithium Iron Phosphate (LiFePO4) | Unit voltage 3.2V * number of strings (2-45 strings adjustable) | |||
| Ternary Lithium Battery (Li-ion) | Unit voltage 3.7V * number of strings (2-45 strings adjustable) | |||
| User Defined | Equalizing charge, floating charge, DC discharge limit voltage adjustable: 8V - 170V | |||
| Lithium Battery Activation Function | With photovoltaic input, there is charging voltage (activates lithium battery), can be used without battery DC output. | |||
| Photovoltaic Minimum Voltage Start Charging | PV voltage is greater than +3V of battery voltage (low current charging on rainy days). | |||
| PV Maximum Open Circuit Input Voltage (VOC) | 0-230V | |||
| Photovoltaic Charging Current Adjustable | 0-30A / 0-40A | 0-50A / 0-60A | 0-80A / 0-100A | |
| DC Current Output (Street Lamp Function) | DC continuous output 25A | DC continuous output 60A | DC continuous output 100A | |
| Temperature Compensation | Automatically compensates charging voltage and current according to battery temperature to prolong battery life. | |||
| LCD Display | Touch button LCD display: (generating capacity / photovoltaic voltage / battery voltage / charging current / power / operation status) in Chinese and English. | |||
| Settings | Battery type, charging current, return to factory. | |||
| 485 Communication | 8-pin RS485 communication interface (operation status and setting can be queried). | |||
| Working Environment Temperature | -20°C ~ +40°C | |||
| Static Power Consumption | 2W | |||
| Overall Efficiency | 96.5% ~ 99% | |||
| Temperature Protection | 85°C | |||
| Temperature Rise Protection | Reduce power output above 80°C. | |||
| Humidity | 0 ~ 90% RH (no condensation) | |||
| Mechanical Protection Level | IP21 | |||
| Altitude | 0 ~ 3000m | |||
| Product Size (L*W*H) | 202mm*215mm*100mm | 218mm*265mm*100mm | 318mm*262mm*108mm | |
| Net / Gross Weight | 1.95KG | 3KG | 4.7KG | |
7. User Tips
- DIY System Planning: For those building their own solar systems, careful planning of PV array size, battery bank capacity, and load requirements is crucial for optimal performance and longevity. Ensure all components are compatible with the controller's specifications.
- Initial Setup: Before fully integrating into your system, it's advisable to perform a basic test of the controller with a small PV panel and battery to familiarize yourself with its operation and display.
- RS485 Communication: If using the RS485 interface for data monitoring, ensure correct A-B wiring. If specific MODBUS commands are needed, contact the seller for detailed protocols.
8. Warranty and Support
The HXCONTROLLER MPPT Solar Charge Controller undergoes thorough quality checks before shipment to ensure you receive a product in good condition.
For immediate assistance with installation, troubleshooting, or any technical queries, please contact our 24/7 technical support team via email.
A detailed user manual in PDF format is available for download and reference: User manual (PDF).