Nasedal R500

Contents

Nasedal R500 LVLP Gravity Feed Spray Gun Instruction Manual

Model: R500 | Brand: Nasedal

1. Introduction

The Nasedal R500 LVLP (Low Volume Low Pressure) Gravity Feed Spray Gun is designed for efficient and high-quality paint application across various projects, including automotive, home, furniture painting, and DIY tasks. Its LVLP technology ensures high coating efficiency with less overspray, meeting international environmental requirements. This manual provides essential information for the safe and effective use and maintenance of your spray gun.

Nasedal R500 LVLP Gravity Feed Spray Gun kit components

Figure 1: Nasedal R500 Spray Gun Kit Components

2. Product Specifications

Feature Specification
Model Number R500
Type LVLP Gravity Feed Spray Gun
Nozzle Diameter 1.3mm
Cup Capacity 600cc (600ml) Plastic Cup
Material Metal (Gun body), Stainless Steel (Nozzle & Needle), Pure Copper (Air Cap)
Air Inlet 1/4"
Recommended Air Pressure 2.0-3.5 bar (28.8-51 psi)
Max Air Pressure 6.8 bar (100 psi)
Air Consumption 84.1-109 L/min (3.5-3.9 cfm)
Pattern Width 180-280mm (7.0"-10.9")
Dimensions (Gun) Approx. 16cm (6.3in) width, 18cm (7.09in) height
Dimensions (Cup) Approx. 10cm (3.94in) width, 15.7cm (6.18in) height
Application Automotive, Car, Home, Furniture Painting, DIY Projects
Diagram of R500 spray gun with labeled parts and specifications table

Figure 2: R500 Spray Gun Labeled Parts and Key Specifications

Dimensions of the Nasedal R500 spray gun and its paint cup

Figure 3: Spray Gun and Cup Dimensions

3. Setup Instructions

  1. Unpack and Inspect: Carefully remove all components from the packaging. Inspect the spray gun, paint cup, and accessories for any damage. Ensure all parts listed in the kit are present (spray gun, 600cc plastic cup, 1.3mm nozzle, air inlet connector, wrench, cleaning brush).
  2. Assemble the Paint Cup: Screw the 600cc plastic paint cup onto the top of the spray gun body. Ensure it is securely tightened to prevent leaks.
  3. Connect Air Supply: Attach the 1/4" air inlet connector to the bottom of the spray gun handle. Connect your air compressor hose to this inlet. It is recommended to use an air pressure regulator and filter (as shown in Figure 4) to ensure clean, regulated air supply.
  4. Prepare Paint: Mix your paint according to the manufacturer's instructions for spray application. Strain the paint to remove any particles that could clog the nozzle.
  5. Fill Paint Cup: Pour the prepared paint into the 600cc plastic cup. Do not overfill.
  6. Initial Adjustments: Before spraying, familiarize yourself with the adjustment knobs: Spray Width Control Knob, Paint Flow Control Knob, and Air Flow Adjust Valve. Start with conservative settings and adjust as needed.
Spray gun with air pressure regulator and filter

Figure 4: Optional Air Pressure Regulator and Filter Setup

Video 1: Nasedal R500 Spray Gun Product Overview and Demonstration

4. Operating Instructions

  1. Adjust Air Pressure: Set your air compressor to the recommended air pressure of 2.0-3.5 bar (28.8-51 psi).
  2. Adjust Spray Pattern:
    • Spray Width Control Knob: Rotate this knob to adjust the width of the spray pattern. Turn clockwise for a narrower pattern, counter-clockwise for a wider pattern (up to 180-280mm).
    • Paint Flow Control Knob: Adjusts the amount of paint released. Turn clockwise to decrease paint flow, counter-clockwise to increase.
    • Air Flow Adjust Valve: Controls the overall air volume.
  3. Test Spray: Always test the spray pattern on a scrap piece of material before applying to your actual project. Adjust the knobs until you achieve the desired pattern and paint coverage.
  4. Spraying Technique:
    • Hold the gun perpendicular to the surface, maintaining a consistent distance (typically 180-250mm).
    • Move the gun at a steady pace, overlapping each pass by about 50%.
    • Release the trigger at the end of each pass to avoid paint buildup.
Diagram showing the three adjustable valve knobs for spray width, paint flow, and air volume

Figure 5: Adjustable Valve Knobs

Images showing various usage scenarios for the spray gun, including wall surfaces, leather sofas, and furniture

Figure 6: Usage Scenarios

5. Maintenance

Proper cleaning and maintenance are crucial for the longevity and optimal performance of your spray gun.

  1. Immediate Cleaning: After each use, immediately empty any remaining paint from the cup. Pour appropriate cleaning solvent (e.g., paint thinner for oil-based paints, water for water-based paints) into the cup. Spray the solvent through the gun until it runs clear.
  2. Disassembly and Detailed Cleaning:
    • Unscrew the air cap and nozzle. Carefully remove the needle.
    • Use the provided cleaning brush and solvent to thoroughly clean the air cap, nozzle, needle, and the inside of the gun body. Pay close attention to small holes and passages.
    • Do not use metal objects to clean the nozzle or air cap, as this can damage them.
    • Clean the paint cup thoroughly.
  3. Lubrication: Apply a small amount of spray gun lubricant to the needle packing and air valve packing after cleaning to ensure smooth operation.
  4. Reassembly: Reassemble the gun, ensuring all parts are correctly seated and tightened.
  5. Storage: Store the clean and dry spray gun in a safe place, away from dust and extreme temperatures.
Cleaning tools including a wrench and a brush for the spray gun

Figure 7: Cleaning Tools

6. Troubleshooting

Problem Possible Cause Solution
Uneven Spray Pattern Clogged air cap or nozzle, incorrect air pressure, paint too thick. Clean air cap and nozzle. Adjust air pressure. Thin paint as per manufacturer's instructions.
No Paint Flow Clogged nozzle, paint cup empty, paint flow knob closed, needle stuck. Clean nozzle. Refill paint cup. Open paint flow knob. Check and lubricate needle.
Excessive Overspray Too high air pressure, gun too far from surface, paint too thin. Reduce air pressure. Move gun closer to surface. Thicken paint or adjust settings.
Paint Dripping from Nozzle Loose nozzle, damaged needle packing, paint flow too high. Tighten nozzle. Replace needle packing. Reduce paint flow.

7. User Tips

  • For Beginners: This spray gun is noted for providing an excellent finish and is a good option for those looking to start painting projects the right way, even without extensive prior experience.
  • Practice Makes Perfect: Before tackling your main project, spend some time practicing on scrap materials to get a feel for the gun's adjustments and your preferred spraying technique.
  • Proper Ventilation: Always work in a well-ventilated area or use appropriate respiratory protection when spraying paints and solvents.
  • Strain Your Paint: Even if your paint seems clean, straining it before pouring into the cup can prevent many common clogging issues.

8. Warranty and Support

For any issues or questions regarding your Nasedal R500 spray gun, please contact the seller or manufacturer's customer support. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.