RainPoint ITC1200

Contents

RainPoint 12-Zone Digital Irrigation Controller User Manual

Model No. ITC1200

Brand: RainPoint

1. Contents in the Box

  • 1 X ITC1200 12-Zone Digital Irrigation Controller
  • 1 X Quick Guide
  • 4 X Screws and Expansion Bolts
  • 1 X User Manual
  • 1 X Warranty Card

2. Product Overview

The RainPoint ITC1200 is a 12-zone digital irrigation controller designed for automatic sprinkler systems. It features a clear LCD display and intuitive operation buttons for easy programming and management of your watering schedules.

Front view of the RainPoint ITC1200 12-Zone Digital Irrigation Controller with its cover open, showing the LCD screen, dial, and control buttons.
Front view of the RainPoint ITC1200 12-Zone Digital Irrigation Controller.

2.1 Button Introduction

ButtonFunction
+Increase a numeric setting
-Decrease a numeric setting
< (Left Arrow)Go back to the previous setting/watering station or move to other programs/settings
> (Right Arrow)Skip to the next setting /watering station or move to other programs/settings
SELECTConfirm settings
CANCELRestore default/clear settings
P (Program)Switch program
MANUAL WATERINGWater manually
MANUAL DELAYManual delay
RAIN SENSORControls rain sensor functionality (ON/OFF for zones)
SEASONAL ADJUSTMENTSets watering percentage for seasonal adjustment

2.2 Dial Position Introduction

Dial PositionFunction
AUTO RUNTurn on automatic irrigation mode and execute the set plan
OFFTurns off all schedules
SET TIMESet the time and date
START TIMESet time to begin watering
RUN TIMESet watering duration for each station
HOW OFTENSet the irrigation frequency

2.3 Product Features

  • Connects to a normally closed rain sensor and set a specified stop irrigation zone.
  • Clear LCD display and operation buttons for easy operation of the product.
  • Each valve (zone) can be set up for a variety of watering plans.
  • Allows setting a delay for rainy days.
  • Provides clear indications and buttons for ease of use.
  • Supports full seasonal adjustment.

3. Specifications

AttributeValue
Model NumberITC1200 (PR1200)
MaterialPlastic
Timer TypeAc Pro
TypeGarden Water Timers, Irrigation Controller
Working Temperature Range3℃~50℃ (37°F~122°F)
Storage Temperature Range-10℃~50℃ (4°F~122°F)
Power Supply230V/120V AC
Valve Output VoltageAC: 24V, holding current<200mA
Backup BatteryCR2032 (for program retention during AC power loss)

4. Installation

4.1 Battery Installation (Optional)

The controller requires a CR2032 battery to maintain your program in case of an AC power loss. A battery alone will not turn on/off the valves in your system.

  1. Turn the key to open the cover of the controller.
  2. Open the middle layer cover.
  3. Use a cross screwdriver to open the battery compartment cover.
  4. Take out the battery compartment and insert the CR2032 battery.
  5. Put it back in the battery compartment and tighten the screw.

Note:

  • Ensure the battery cover is firmly closed.
  • Remove the battery for extended storage.
  • Do not throw batteries into fire, they may explode or leak.
RainPoint controller installed on a wall, showing a backup battery compartment and text indicating schedules are saved during power outages.
Backup battery ensures schedules are saved during power outages.

4.2 Controller Mounting

Find a suitable location near a power socket. Use the provided molding paper as a template to mark drill points on the wall. Drill holes, insert expansion bolts, and secure the controller.

Video: Step-by-step guide for mounting and wiring the controller.
  1. Find a suitable place with a nearby power socket.
  2. Place the molding paper with tape on the wall.
  3. Use an electric drill to drill holes at the corresponding positions marked on the paper.
  4. Drive the expansion bolts into the upper holes and screw in the screws, leaving them slightly out.
  5. Drive the expansion bolts into the lower holes.
  6. Hang the product on the upper screws.
  7. Pass the screws through the lower holes of the product and fix them.
Close-up of the RainPoint ITC1200 controller mounted on a wall, showing the LCD and control panel.
The controller mounted on a wall.

4.3 Wire Connections

WARNING: Always disconnect the power supply before wiring to avoid electric shock.

4.3.1 Valve Wiring

Strip the appropriate length of insulation from each wire. Connect the wires from the valve to the zones (1-12), one to the 'C' wire, and the other to the respective zone terminals. Connect the wires from the transformer to the AC terminals, or power the irrigation controller by the included AC adapter.

Internal wiring terminals of the RainPoint ITC1200 controller, showing connections for SENSOR, C, M, and zones 1-12, along with 120V AC power input.
Internal wiring terminals for valves and power.

Note:

  • Each zone can only be connected with one wire.
  • If there is a main valve, connect its wires to the C and M zone on the left side of all zones.
  • If unsure about the solenoid valve model, consult the original manufacturer.

4.3.2 Rain-Sensor Wiring (Optional)

The SENSOR port ships with a shorting jumper. Remove this jumper only when connecting an NC rain sensor.

  1. Remove an appropriate length of insulation from the sensor lead.
  2. Connect the two wires of the rain sensor to the two terminals of the SENSOR (non-polarized).
Diagram showing a RainPoint rain sensor installed on a gutter, connected to the controller, with sprinklers in the background.
Rain sensor installation example.

Note:

  • Rain sensor affects designated zones only.
  • The rain sensor is a normally closed type. When the shorting wire is disconnected, or when the normally closed rain sensor detects rain, the zone affected by the rain sensor displays "ACT" (active). The zone activated by the rain sensor cycles between the next irrigation time and the next 3 seconds.

5. Operating Instructions

After connecting the AC power cord, turn the dial to the desired setting mode.

Simplified programming steps for the RainPoint controller, showing options for Program (P1, P2, P3), Start Time (x4), How Long (1min to 4hrs), and How Often (Week, Interval, Odd/Even Days).
Simplified programming overview.

5.1 Set Date and Current Time

  1. Turn the dial to SET TIME.
  2. Press '+' or '-' to select the date format (MM/DD/YYYY or DD/MM/YYYY). Press 'SELECT' to confirm.
  3. Press '+' or '-' to set the date. Press 'SELECT' to confirm.
  4. Press '+' or '-' to select between 12-hour / 24-hour formats. Press 'SELECT' to confirm.
  5. Press '+' or '-' to adjust the hour / minutes. Press 'SELECT' to confirm.

Note:

  • During setup, the left button returns to the previous level for readjustment. The right button advances.
  • If the battery is installed, the program will be saved during AC power failure, but watering will not occur.

5.2 Set Start Time

  1. Turn the dial to START TIME.
  2. PROGRAM 1 is displayed by default. Press 'P' to switch between PROGRAM 2 or PROGRAM 3.
  3. Press '+' or '-' to set the start-time hour. Press 'SELECT' to confirm and proceed to minutes, then press '+' or '-' to set the minute.
  4. After one start time is set, press 'SELECT' to move to the next start time. Each program can have a maximum of four start times.
  5. To delete or reset a programmed start time, press 'CANCEL'. The time will return to '--:--'.

After completing the settings, turn the dial to save and proceed with the next steps.

5.3 Set Watering Duration

  1. Turn the dial to RUN TIME.
  2. PROGRAM 1 is displayed by default. Press 'P' to switch between PROGRAM 2 or PROGRAM 3.
  3. Press '+' or '-' to set the run time (range 0 – 240 min).
  4. Press 'SELECT' to move to the next zone. The Zone range is 1-12 and ALL. When ALL is set, all zones will execute the plan with a unified duration.

Note:

  • To reset the set Run Time, short press 'CANCEL' to restore to 0 min.
  • If the run time of a program is 0 min but Start time is set, the program will not be opened.

5.4 Setting Watering Frequency

Turn the dial to HOW OFTEN to set the irrigation frequency. PROGRAM 1 is displayed by default. There are three modes: Week Mode, Interval Mode, and Date Mode. Press the 'SELECT' button to confirm and enter the setting of this mode.

5.4.1 Week Days Watering

  1. Turn the dial to HOW OFTEN.
  2. Press 'SELECT' to choose from Week.
  3. Press 'SELECT' or 'SELECT' to scroll through the days. Press 'SELECT' to mark a day (water droplet icon appears). Press 'SELECT' again to cancel the selection (water droplet icon disappears).

5.4.2 Interval Days Watering

  1. Turn the dial to HOW OFTEN.
  2. Press 'SELECT' to navigate to Interval, then press 'SELECT' to confirm.
  3. Press '+' or '-' to set the interval days (Range 1 – 30 days).

5.4.3 Odd or Even Days Watering

  1. Turn the dial to HOW OFTEN.
  2. Press 'SELECT' to navigate to Date, then press 'SELECT' to confirm.
  3. Press 'SELECT' or 'SELECT' to select between ODD or EVEN. Press 'SELECT' to confirm.

Note:

  • To reset the irrigation frequency, short press 'CANCEL' to restore to mode selection.
  • During setting, you can press 'P' to switch programs. Each program starts from mode selection when set for the first time.
  • If the week mode of a program does not select any day, the program will not open.

5.5 Automatic Operation

Turn the dial to AUTO RUN. All set plans will be executed according to the settings. The screen displays the program, zone, irrigation date, valve opening time, and irrigation duration of the most recent opening.

When a valve is open:

On the LCD display, the irrigation date and duration will enter a countdown, and the countdown number and water droplets on the right side of the zone will flash.

Operable actions:

  • Switch: Short press the right button to immediately close the current valve, switch to the next valve. If no subsequent valve, the plan closes.
  • Close: When a plan is active, short press the 'CANCEL' button to immediately cancel the plan and close all roads.

5.6 Manual Watering (Supplemental Watering)

In the AUTO RUN state, short-press the MANUAL WATERING key to enter manual irrigation mode. A triangle icon appears in the lower left corner. The zone number and duration start flashing, with default settings of zone ALL and 0 min. Use the left and right keys to switch zones, and the '+' or '-' keys to set the duration. After setting, press 'SELECT' to activate manual irrigation, or it will default to on after 5 seconds. Once activated, return to the main page, select the valve to open immediately, and the screen will display the countdown for irrigation.

Notes:

  • The manual valve opening setting is set to either open one or fully open two times.
  • To turn it off: Turn the dial to OFF or any other position, or short press the 'CANCEL' key to stop manual irrigation.

5.7 Manual Delay (Skip The Watering)

In the AUTO RUN state, short press the MANUAL DELAY key to enter manual delay mode. A triangle icon appears at the bottom of the screen, indicating the number of days for the delay. The default is 1 day, with a range of 0-30 days. Set the value using the '+' or '-' keys. After setting, press 'SELECT' to activate the manual delay mode, or it will be automatically enabled after 5 seconds. After the delay is enabled, it will automatically return to the main page and start the countdown. The water droplet above the week will follow the rain delay change. If the planned week is delayed, the water droplet above the week will disappear.

Note:

  • To disable the rain delay: Short press 'CANCEL' to cancel the delay.

5.8 Seasonal Adjustment

In the AUTO RUN state, short-press the SEASONAL ADJUSTMENT key to enter seasonal irrigation settings. Use the left or right buttons to change the month. Use the '+' or '-' buttons to set the watering percentage according to needs (Available Range: 0%-200%). After completing the monthly configurations, press the SEASONAL ADJUSTMENT button again to save and exit, or it will automatically save and return after 5 seconds of inactivity.

Table showing seasonal adjustment percentages for each month, ranging from 10% to 200%.
Seasonal Adjustment Reference Table.

Notes:

  • Adjustments take effect in real-time but are not reflected in scheduled settings. The system automatically adjusts the runtime of the active watering schedule.
  • Initial default setting for all months is 100%.
  • Adjustments are made in 10% increments, with a range from 10% to 200%.

5.9 Rain Sensor Settings

In the AUTO RUN state, short-press the RAIN SENSOR key to enter rain sensor settings. The rain sensor icon will display ON, indicating the rain sensor affects this zone. Press the left or right keys to switch zones, and press 'SELECT' to set ON/OFF for this zone. After setting, press the RAIN SENSOR key again to confirm and return, or it will automatically save and return after 5 seconds.

When setting, short press RAIN SENSOR to enter the setting. When zone 11 flashes and press 'SELECT', the ON next to rain sensor on the bottom becomes OFF, indicating the rain sensor no longer controls or affects the zone 1 plan. If you press 'SELECT' again, it will become ON again.

Diagram illustrating how rain delay is applied to selected zones, showing some zones continuing to run while others are shut off due to rain.
Rain Delay application to zones.

6. Troubleshooting

ProblemPossible FactorsSolution
The valve cannot be openedThe wire at the connection is loose.Press the terminal and tighten the wire.
The plan was not implemented on timeActivate the rain delay function.Check if rain delay is set. Whether the power supply is disconnected.

7. Precautions

  • Tighten the screws when installing it on the wall.
  • Always disconnect the power supply before wiring to avoid electric shock.

8. Warranty & Support

8.1 Warranty Policy

RainPoint provides a 1-year limited warranty on this product against manufacturing defects in materials and workmanship.

  • Warranty service can only be performed by our authorized service center. The original dated bill of sale must be presented upon request as proof of purchase.
  • To receive warranty service, contact RainPoint's nominated service center for problem determination and service procedure.

8.2 Customer Support

If you need assistance with setup or prefer a visual guide, you can subscribe to the RainPoint channel on YouTube. Scan the QR code below to access the channel.

QR code to RainPoint's YouTube channel for setup tutorials.
Scan for YouTube tutorials.

For further support or if the user manual doesn't cover your specific query, please contact RainPoint support via email:

support@rainpointonline.com

Please provide the LOT NO. (XXXXXX on the device) when contacting support.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.