1. Introduction
The Estardyn ESP32-C3 Board is a compact and powerful development board featuring an ESP32-C3 microcontroller, a 2.4-inch TFT LCD touch screen, and integrated WiFi and Bluetooth 5.0 connectivity. Designed for a wide range of IoT applications, this board supports programming with IDEs like Arduino and MicroPython, making it suitable for smart home devices, wearables, and other embedded projects.
2. Setup Guide
2.1. Package Contents
- Estardyn ESP32-C3 Board with 2.4" TFT LCD Touch Screen
- (Optional: USB-C cable, depending on package)
2.2. Powering the Board
The board can be powered via the USB-C interface (5V) or through the 3.3V pin. Ensure a stable power supply to prevent unexpected behavior.
2.3. Connecting to a Computer
Connect the board to your computer using a USB-C cable. The board should be recognized as a serial device. You may need to install appropriate USB-to-serial drivers if not automatically detected by your operating system.
2.4. Pinout Diagram and Functions
Refer to the diagram and table below for the pin assignments and their respective functions. This information is crucial for connecting external components and understanding the board's capabilities.

| Serial Number | PCB Symbol / Function | Meaning |
|---|---|---|
| 1 | 5V | 5V power supply |
| 2 | GND | Ground |
| 3 | 3.3V | 3.3V power supply |
| 4 | TX0 | UART0 Transmit, GPIO 21 |
| 5 | RX0 | UART0 Receive, GPIO 20 |
| 6 | GND | Ground |
| LCD Display Interface (White dots represent pin 1) | ||
| 7-1 | GND | Ground: Power Ground |
| 7-2 | CS | LCD Chip Select/Command Selection, GPIO 10 |
| 7-3 | SCK | LCD SPI clock, Chip Select signal, connected to Ground |
| 7-4 | SDA | LCD SPI Data (MOSI), GPIO 7 |
| 7-5 | RES | Reset, LCD reset, GPIO 8 |
| 7-6 | VCC | Logic power supply, 3.3V power supply |
| 7-7 | GND | Ground: Power Ground |
| 7-8 | LEDK | Backlight negative terminal, controlled by GPIO 0, with high level as the ON signal |
| 7-9 | LEDA | Backlight positive terminal, controlled by GPIO 0, with high level as the ON signal |
| Touch Interface (White dots represent pin 1) | ||
| 8-1 | TP_VDD | Touch power supply, 3.3V power supply |
| 8-2 | TP_SCL | Touch I2C clock, GPIO 4 |
| 8-3 | TP_SDA | Touch I2C data, GPIO 3 |
| 8-4 | TP_RST | Touch reset, GPIO 2 |
| 8-5 | GND | Ground: Power Ground |
| 9 | LED | Indicator light: GPIO_1 low voltage state means the light is on |
| 10 | Power indicator light | Always on when powered |
| 11 | BOOT | Press the BOOT download mode button, hold down and then start the ESP32 to enter ESP32 reset mode |
| 12 | Reset | WiFi + Bluetooth PCB board built-in antenna |
| 13 | USB | USB interface |
| 14 | ESP32-C3 | ESP32-C3F4 main controller |
2.5. Development Environment Setup
The Estardyn ESP32-C3 board is compatible with various development environments, including the Arduino IDE and MicroPython. For detailed instructions on setting up your preferred environment, please refer to the official Espressif documentation or community resources for ESP32-C3 boards.
- Arduino IDE: Install the ESP32 board package through the Boards Manager.
- MicroPython: Flash the MicroPython firmware to the ESP32-C3 and use a serial terminal or IDE like Thonny.
3. Operating Instructions
3.1. Uploading Code
Once your development environment is set up and the board is connected, you can compile and upload your code. Ensure the correct board and port are selected in your IDE. For entering download mode, press and hold the BOOT button (11) while pressing and releasing the Reset button (12), then release BOOT.
3.2. Using the TFT LCD Touch Screen
The 2.4-inch TFT LCD (ST7789 driver) and touch screen (I2C interface) can be controlled via the dedicated pins (7-1 to 7-9 for LCD, 8-1 to 8-5 for Touch). Libraries such as Adafruit_GFX and TFT_eSPI for Arduino, or respective MicroPython modules, can be used to draw graphics, display text, and read touch input.
3.3. WiFi and Bluetooth Connectivity
The ESP32-C3 features integrated 2.4GHz WiFi (802.11b/g/n) and Bluetooth 5.0 (BLE). Use the standard ESP-IDF or Arduino WiFi/Bluetooth libraries to connect to networks, create access points, or communicate with other Bluetooth devices.
4. Maintenance
4.1. Cleaning
To clean the board, ensure it is powered off and disconnected from all power sources. Use a soft, dry, anti-static cloth to gently wipe the PCB and screen. Avoid using liquids or abrasive materials.
4.2. Firmware Updates
Periodically check for updated firmware or board definitions for your chosen development environment. Keeping your firmware up-to-date can provide new features, performance improvements, and bug fixes. Follow the specific update procedures provided by Espressif or your IDE's community.
5. Troubleshooting
- Board not recognized by computer: Ensure USB-C cable is functional and data-capable. Install necessary USB-to-serial drivers (e.g., CP210x or CH340 drivers).
- Code upload fails: Verify correct board and port selection in IDE. Ensure the board is in download mode (press BOOT, then Reset, then release BOOT). Check for correct wiring if using external programmer.
- Display not working: Check power supply to the LCD (VCC, 3.3V). Verify all LCD interface pins (7-1 to 7-9) are correctly connected and initialized in your code. Ensure backlight (LEDK/LEDA) is properly controlled.
- Touch screen unresponsive: Check power supply to the touch controller (TP_VDD, 3.3V). Verify I2C connections (TP_SCL, TP_SDA) and reset pin (TP_RST) are correct. Ensure I2C address is correctly configured in software.
- WiFi/Bluetooth connectivity issues: Check antenna connection (built-in PCB antenna). Verify correct library usage and network credentials. Ensure sufficient power supply for wireless operations.
6. Specifications
| Feature | Detail |
|---|---|
| Brand Name | Estardyn |
| Model Number | ESP32-C3 2.4 TFT |
| Type | TFT Development Board |
| Display Mode | 240*320 |
| Resolution | 320*240 |
| Processor | ESP32-C3 (32-bit RISC-V single-core, up to 160MHz) |
| Wireless Connectivity | WiFi (802.11b/g/n), Bluetooth 5.0 (BLE) |
| Memory | 4MB Flash, 320KB SRAM |
| Origin | Mainland China |
| Package Length | 14 cm |
| Package Width | 10 cm |
| Package Height | 2 cm |
| Package Weight | 0.051 kg |
7. User Tips
- Start with Examples: Begin with simple example sketches or MicroPython scripts to familiarize yourself with the board's basic functionalities, especially the display and touch features.
- Power Considerations: When adding many peripherals or using WiFi/Bluetooth extensively, ensure your power supply can provide sufficient current to avoid unexpected resets or instability.
- Community Support: The ESP32 community is vast and active. Utilize online forums, documentation, and tutorials for advanced projects or specific troubleshooting.
- Pin Mapping: Always double-check the pin mapping in your code against the physical pinout diagram to prevent damage to the board or connected components.
8. Warranty and Support
This product comes with a standard manufacturer's warranty against defects in materials and workmanship. For technical support, detailed documentation, or warranty claims, please refer to the official Estardyn website or contact their customer service. Keep your purchase receipt for warranty validation.