HITBOX HBM145

Contents

HITBOX HBM145 4-in-1 MIG Welder User Manual

Model: HBM145

Brand: HITBOX

1. Introduction

Thank you for choosing the HITBOX HBM145 4-in-1 MIG Welder. This machine is designed for versatile welding applications, including Gasless MIG, MMA (Stick), and Lift TIG. It features advanced IGBT inverter technology for stable and consistent welding performance. This manual provides essential information for safe operation, installation, maintenance, and troubleshooting. Please read it thoroughly before using the product.

For further details and support, you may refer to the official user manual PDF available from the manufacturer.

2. Safety Instructions

WARNING: Welding is dangerous and can cause harm to you and others. Always protect yourself when welding.

  • Professional Training: Only operate the machine after receiving professional training and possessing a valid "Metal Welding (OFC) Operation" certificate.
  • Power Disconnection: Always cut off power before any maintenance or repair.
  • Electrical Safety: Never touch a charged area with bare skin or wet gloves/clothing. Ensure proper insulation from the ground and workpiece.
  • Fume Inhalation: Keep your head away from smoke and gases. Use exhaust or ventilation equipment to ensure a well-ventilated working environment.
  • Eye and Body Protection: Wear a comfortable welding mask and protective clothing to protect your eyes and body. Use a suitable mask or screen to protect others from harm.
  • Fire and Explosion Hazard: Welding sparks can cause fires. Ensure no combustible materials are nearby. Have fire extinguishers readily available and know how to use them. Container welding is strictly prohibited.
  • Hot Workpieces: High temperature workpieces can cause severe burns. Do not touch hot workpieces with bare hands. Allow the torch to cool during continuous use.
  • Pacemakers: Magnetic fields can affect pacemakers. Individuals with pacemakers should stay away from the solder joint and consult medical attention.
  • Moving Parts: Keep hands, hair, and tools away from moving parts such as fans. Ensure all doors, panels, and lids are closed during operation.
  • Machine Failure: In case of machine failure, consult the relevant sections of this manual or contact the service center for professional help.
Safety icons for welding
Visual representation of safety warnings including electrical shock, fumes, eye protection, and fire hazards.

3. Product Features and Overview

The HITBOX HBM145 is a multi-process inverter welder designed for efficiency and portability. It incorporates IGBT technology for stable arc performance and reduced spatter.

Key Features:

  • 4-in-1 Welding Modes: Supports Gasless MIG, MMA (Stick), Lift TIG, and Spool Gun (Spool gun and TIG torch require separate purchase).
  • Portable Design: Compact and lightweight (approx. 9.63 lbs / 4.5 kg machine weight) for easy transport and use in various locations. Dimensions: 13.7 x 9.6 x 6.4 inches.
  • Smart Device Integration: Enhances usability and efficiency.
  • High Power Output: 120A for MMA, MIG, and Lift TIG.
  • Large LED Display: Provides clear visibility of welding thickness, process, and other parameters.
  • Synergic Control: Beginner-friendly, automatically matches wire feed speed and voltage in MIG mode.
  • Advanced Protection: Overvoltage, Overcurrent, Overheating, and Overload Protection.
  • Durable Construction: Features a waterproof power switch to prevent water and dust ingress, extending welder lifespan and suitable for outdoor use.
  • Premium Welding Performance: Includes Hot Start, Arc Force, and Anti-stick functions for MMA.
HITBOX HBM145 MIG Welder front view
Front view of the HITBOX HBM145 MIG Welder, highlighting its compact design.
HITBOX HBM145 MIG Welder with accessories
The HITBOX HBM145 MIG Welder shown with included accessories: 14AK MIG Gun, Electrode holder, Earth Clamp, Flux Core Wire, Manual, Hammer, Nozzle, Welding Rods, and Conductive Nozzles.
HITBOX HBM145 MIG Welder showing multiple welding modes
Illustration of the 4-in-1 capabilities: Gasless MIG, MMA, Lift TIG, and Spool Gun welding.
HITBOX HBM145 MIG Welder control panel display
Close-up of the digital control panel, showing settings for flux core wire (0.8mm, 1.0mm), current (145A), and welding thickness (2.5mm), along with indicators for Hot Start, Arc Force, Antisticking, and VRD.
HITBOX HBM145 MIG Welder internal components and protection features
Internal view of the welder highlighting Overvoltage, Overcurrent, Overheating, and Overload Protection features.
HITBOX HBM145 MIG Welder with spool gun
The HITBOX HBM145 MIG Welder connected to a spool gun (extra purchase required) for gasless welding.
Official product video demonstrating the features and operation of the HITBOX HBM145 MIG Welder.

4. Specifications

ParameterValue
ModelHBM145
Input Voltage (V)AC 110/220V ± 15%, 50/60Hz
Rated Input Current (A)AC 110V 40A / AC 220V 20A
Rated Input Capacity (KVA)4.5
Recommended Fuse Capacity (A)30
MMA Weld Current Range (A)10~120
MIG Welding Current Range (A)20~120
MIG Voltage Range (V)11~20
No-load Voltage (V)55
Wire Feeding Speed Range (m/min)1.5~14
Applicable Wire Diameter (mm)0.8/1.0
Rated Duty Cycle35% / 25°C
Efficiency0.8
Factor0.75
Protection ClassIP21S
Insulation ClassF
Dimensions (L x W x H)35 x 16 x 25 cm (Machine)
Weight4.5 kg (Machine)
CertificationsCE, FCC, RoHS

Panel Description:

Front Panel:

  1. Current Display
  2. 0.8/1.0 Indication (Wire Diameter)
  3. Spool Gun Mode Indicator
  4. MMA Mode Indicator
  5. TIG Mode Indicator
  6. MIG Mode Indicator
  7. "-" Output Terminal
  8. Abnormal Indication
  9. Function Switching Button
  10. Mode Switching Button
  11. Current Control Knob
  12. "+" Output Terminal
  13. MIG Torch Switch
Front panel diagram of HBM145 welder
Diagram of the front panel with numbered components and their descriptions.

Back Panel:

  1. Power Cord Input
  2. Power Switch
Back panel diagram of HBM145 welder
Diagram of the back panel showing the power cord input and power switch.

5. Installation and Setup

Note:

  • Always turn off the power switch before any electrical or electronic connection.
  • This machine has an IP21S protection rating; avoid using it in the rain.

5.1 Connection of Input Cables

  1. Connect the main power cable to a rated input power supply. Grounding connections are required for safety.
  2. Ensure the primary cable is tightly connected to the correct socket to prevent oxidation.
  3. Verify the voltage value changes within an acceptable range using a multimeter.

5.2 MMA (Stick) Installation

  1. This welding machine has two quick plugs. Plug the quick plug into the corresponding socket on the front panel and tighten it clockwise to ensure good contact. Poor contact can lead to burning of plugs/sockets during prolonged high-current operation.
  2. Plug the cable with the electrode holder into the “+” socket on the front panel and tighten clockwise.
  3. Plug the cable with the work clamp into the “-” socket on the front panel and tighten clockwise.
  4. DCEP (Direct Current Electrode Positive): Connect the electrode holder to the "+" output terminal and the work fixture to the "-" output terminal.
  5. DCEN (Direct Current Electrode Negative): Connect the electrode holder to the "-" output terminal and the work fixture to the "+" output.
  6. Choose the connection method based on workpiece and electrode requirements. Incorrect connection can cause unstable arc, excessive splashing, and electrode adhesion.
  7. If secondary cables (welding and ground) are long, use a larger cross-section cable to reduce voltage drop.
ARC welding setup diagram
Diagram illustrating the setup for ARC (MMA) welding.

5.3 MIG Installation

  1. Connect the main power cable to the rated input power supply, ensuring proper grounding.
  2. Plug the quick plug on the wire feeder into the "+" socket on the front panel and tighten clockwise.
  3. Plug the cable with the work clamp into the "_" socket on the front panel and tighten clockwise.
  4. Install the MIG torch and mount the spool on the rotating shaft. Ensure the groove dimensions at the feed position on the drive roller match the contact tip size and wire diameter.
  5. Insert the aviation plug of the wire feeder into the aviation socket on the front panel. Press the wire snap button to feed the wire out of the torch head.
  6. Connect the wire feeder to the flow regulator on the gas cylinder with a tubing (if using gas-shielded MIG).
MIG + Flux Core welding setup diagram
Diagram illustrating the setup for MIG + Flux Core welding.
MIG + Spool Gun welding setup diagram
Diagram illustrating the setup for MIG welding with a spool gun.

5.4 Lift TIG Installation

  1. Connect the main power cable to the rated input power supply, ensuring proper grounding.
  2. Connect the TIG torch (WP17V TIG Torch needs purchasing separately) to the appropriate terminal.
  3. Connect the work clamp to the workpiece.
Lift TIG welding setup diagram
Diagram illustrating the setup for Lift TIG welding.

6. Operating Instructions

6.1 General Operation

  1. After installation, turn on the air switch on the back panel. The power LED should light up, and the fan should start.
  2. Select the desired welding mode (MMA/MIG/TIG) using the mode switching button on the front panel.
  3. Adjust the welding current and other parameters using the control knob based on the workpiece thickness and welding requirements.

6.2 MIG Welding Programs

6.2.1 Current Setting (Short-Circuit Transition)

The welding current should be set after preparation. For thin electrodes, low voltage, and low current, short-circuit transition ensures stable welding, less spatter, and beautiful weld beads.

Electrode φ (mm)Applicable Current (A)Optimum Current (A)
0.850~12070~100
1.070~18080~120
1.280~350100~200

6.2.2 Wire Speed Selection

Welding quality and productivity depend on wire speed. Increased speed can weaken protective effects and speed up cooling, potentially affecting weld molding. Too slow a speed can burn through the workpiece. Optimal welding speed should not exceed 50cm/min.

6.2.3 Reach to Select (Electrode Extension)

Increased elongation improves productivity, but excessive elongation can lead to spattering, wire breakage, and unstable welding. Generally, the extension should be 10 times the electrode diameter.

6.2.4 Protective Gas Flow Selection (for Gas-Shielded MIG)

Protective effect is paramount. Inner fillet welding generally requires less airflow than outer fillet welding. Less or no shielding gas is needed for FCAW (Flux-Cored Arc Welding).

Welding MethodGas Flow (1/min)
W-type weld wire with thin wire5~15
Welded with coarse wire15~20
Welded with thick wire at high currents20~25

6.3 MMA Welding Current Guidelines

The welding current for MMA mode should be adjusted based on electrode diameter:

  • φ2.5: 70-100A
  • φ3.2: 110-160A
  • φ4.0: 170-220A
  • φ5.0: 230-280A

6.4 Welding Parameter Tables (Reference Only)

Welding current and voltage significantly impact stability, quality, and productivity. Optimal settings depend on electrode diameter, metal transfer method, and production requirements. The following tables provide reference parameters.

6.4.1 Type I Butt Weld Parameters

Plate Thickness t (mm)Gap g (mm)Electrode mmWelding Current (A)Welding Voltage (V)Welding Speed (cm/min)Gas Flow (l/min)Layer
1.201.070-8017-1845-55101
1.601.080-10018-1945-5510-151
2.00-0.51.0100-11019-2040-5510-151
2.50.5-1.01.0 or 1.2110-13019-2050-5510-151
3.21.0-1.21.0 or 1.2130-15019-2140-5010-151
4.51.2-1.51.2150-17021-2340-5010-151

6.4.2 Flat Angle Welding Parameters

Plate Thickness t (mm)Corn Size l (mm)Electrode Φ mmWelding Current (A)Welding Voltage (V)Welding Speed (cm/min)Gas Flow (l/min)
1.22.5-3.01.070-10018-1950-6010-15
1.62.5-3.01.0-1.290-12018-2050-6010-15
2.03.0-3.51.0-1.2100-13019-2050-6010-20
2.52.5-3.01.0-1.2120-14019-2150-6010-20
3.23.0-4.01.0-1.2130-17019-2145-5510-20
4.54.0-4.51.2190-23022-2445-5510-20

6.4.3 Fillet Weld Parameters in Vertical Position

Plate Thickness t (mm)Corn Size l (mm)Electrode Φ mmWelding Current (A)Welding Voltage (V)Welding Speed (cm/min)Gas Flow (l/min)
1.22.5-3.01.070-10018-1950-6010-15
1.62.5-3.01.0-1.290-12018-2050-6010-15
2.03.0-3.51.0-1.2100-13019-2050-6010-20
2.53.0-3.51.0-1.2120-14019-2150-6010-20
3.23.0-4.01.0-1.2130-17022-2245-5510-20
4.54.0-4.51.2200-25023-2645-5510-20

6.4.4 MAG Welding Parameters (Carbon Steel, Iron, Galvanized Sheet)

Gas: Ar+CO2 gas mixture (10 to 15 l/min).

Plate Thickness (mm)Junction TypeElectrode mmDifference (mm)Current (A)Voltage (V)Welding Speed (cm/min)
1.0Type I1.0050-5513-1540-55
1.2Type I1.0060-7014-1630-50
1.6Type I1.00100-11016-1740-60
2.3Type I1.0 or 1.20-1.0110-12017-1830-40
3.2Type I1.0 or 1.21.0-1.5120-14017-1925-30
4.0Type I1.21.5-2.0150-17018-2125-40

7. Maintenance

WARNING: Maintenance operations require electrical expertise and comprehensive safety knowledge. Only qualified operators should perform these tasks. Always cut power before maintenance.

  • Circuit Connections: Periodically check internal circuit connections, especially plugs. Tighten loose connections. If oxidation is present, remove it with sandpaper and reconnect.
  • Moving Parts: Keep hands, hair, and tools away from moving parts like fans to prevent injury or damage.
  • Cleaning: Regularly clean dust with dry, compressed air. If welding in a smoky or polluted environment, clean the machine daily. Ensure compressed air is at an appropriate temperature to avoid damaging small parts.
  • Moisture Protection: Avoid rain, water, and vapor infiltration. If exposed, dry the machine and check insulation between connections and housing before use.
  • Cable Inspection: Periodically check the insulation cover of all cables. Replace any worn or damaged parts.
  • Trachea Inspection: Regularly check the trachea for cracks and replace if necessary.
  • Storage: If unused for a long time, store the machine in a dry place in its original packaging.

8. Troubleshooting

WARNING: Before troubleshooting, ensure the machine's input cable has been disconnected from the power utility.

SymptomCheck Steps
The overheating LED is on.
  1. Check welding current and time; operate as per manual.
  2. Check fan operation. If not working, check 230V power supply to fan. If power supply is normal, check fan. If abnormal, check connection cable.
  3. If thermal switch is damaged, replace it.
No response when pressing gun trigger, protection LED is off.
  1. Check if power LED and digital meter are lit.
  2. Check torch trigger and connection.
  3. Check wire feeder connection.
Wire feeder sends wire into gas when pushing gun trigger, but no output current and protection LED is off.
  1. Check power cord contact with workpiece.
  2. Check quick plug connection.
  3. Check wire feeder connection.
  4. Inspect welding torch for damage.
  5. Internal control of machine PCB PK-94 may have failed.
Output current when pushing gun trigger, but wire feeder does not send wire.
  1. Inspect wire feeder for blockage or damage.
  2. Inspect welding torch contacts for blockages or damage.
  3. Wire feed plate PK-93 may be faulty.
Welding can be performed when torch trigger is pressed, but voltage cannot be adjusted. No-load voltage is too high.
  1. Check control cable of wire feeder.
  2. Control PCB inside machine may have failed.
Welding current is unstable.
  1. Check pressure arm on wire feeder.
  2. Check drive roller matches wire size.
  3. Check contact tip of welding torch for wear; replace/tighten if necessary.
  4. Check welding wire quality.
  5. Check if torch cable is twisted.
  6. Check if quick plug is loose.
Weld is not well protected.
  1. Do not immediately remove torch after stopping welding; allow protective gas to shield beads.
  2. Extend afterflow time of protective gas.
Large pit after welding.
  1. Select 4T mode for crater welding at low currents.
  2. Change operating mode.

9. User Tips

Based on common user experiences and questions:

  • For beginners, the synergic control feature in MIG mode simplifies setup by automatically matching wire feed speed and voltage. Start with recommended settings and fine-tune as needed.
  • Always ensure proper ventilation, especially when welding indoors, to avoid inhaling fumes.
  • Regularly check and clean the wire feeder and torch contact tips to ensure consistent wire feeding and stable arc.
  • When switching between welding modes (MMA, MIG, TIG), double-check all cable connections and polarity to prevent issues.
  • Consider purchasing the optional spool gun for enhanced gasless welding capabilities, particularly for longer distances or specific materials.

10. Warranty and Support

HITBOX welders are built from high-quality components and undergo rigorous lab tests. Your satisfaction is a top priority. If you have any questions or concerns, please feel free to contact HITBOX for support.

For detailed warranty information and service, please refer to the official user manual PDF provided with your product or contact the manufacturer directly.

The official user manual (PDF) can be referenced for comprehensive guides and documents.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.