Estardyn 12864 SPI LCD Module

Contents

Estardyn 12864 SPI LCD Module User Manual

Model: 12864 SPI LCD Module

1. Introduction

This manual provides detailed instructions for the setup, operation, and maintenance of the Estardyn 12864 SPI LCD Module. This module is a 128x64 dot matrix graphic display screen, ideal for various embedded projects requiring a compact and clear visual output.

Estardyn 12864 SPI LCD Module showing different screen types
Figure 1: Estardyn 12864 SPI LCD Module with various screen color options.

2. Specifications

The following table outlines the key specifications of the Estardyn 12864 SPI LCD Module:

Attribute Value
Model Number 12864 SPI LCD Module
Display Mode 128*64
Resolution 128*64
Type Standard
Brand Name Estardyn
Origin Mainland China
High-concerned chemical None
is_customized Yes
Detailed dimensions and pinout diagram for Estardyn 12864 SPI LCD Module
Figure 2: Module Dimensions and Pinout Diagram. Key notes include Display Type: FSTN, Driver IC: ST7567A, Operating Temp: -20°C~70°C, Storage Temp: -30°C~80°C, Interface: SPI, Dot Pitch: 0.3*0.3mm, Dot Size: 0.28*0.28mm.

3. Setup Instructions

Follow these steps to properly connect and set up your 12864 SPI LCD Module:

  1. Identify Pins: Refer to Figure 2 for the pinout diagram. The module uses a Serial Peripheral Interface (SPI) for communication.
  2. Power Connection:
    • Connect VCC to your power supply (typically 3.3V or 5V, check your specific module's voltage requirements).
    • Connect GND to the ground of your power supply and microcontroller.
  3. SPI Communication Pins:
    • SCL (Serial Clock): Connect to your microcontroller's SPI clock pin.
    • SDA (Serial Data): Connect to your microcontroller's SPI data (MOSI) pin.
    • CS (Chip Select): Connect to a digital output pin on your microcontroller to enable/disable the LCD module.
  4. Control Pins:
    • DC (Data/Command): Connect to a digital output pin on your microcontroller to switch between data and command modes.
    • RST (Reset): Connect to a digital output pin on your microcontroller for hardware reset, or to the microcontroller's reset line.
  5. Backlight (BL) and Backlight Control (CS-F, OUT):
    • BL: Backlight power.
    • CS-F, OUT: These pins might be related to backlight control or other specific features. Consult your microcontroller's library or specific module documentation for their exact function if needed.
  6. Software Setup: Install the appropriate display library for your microcontroller (e.g., Arduino IDE libraries for ST7567A driver). Initialize the display with the correct pin assignments.
Close-up of the LCD module showing the back PCB with pin labels
Figure 3: Rear view of the 12864 SPI LCD Module, highlighting the pin connections.

4. Operating Instructions

Once the module is wired and the software library is set up, you can begin displaying content:

  • Initialization: In your code, call the display's initialization function. This typically sets up the display controller (ST7567A) with default parameters.
  • Clearing the Display: Use the `clearDisplay()` function (or equivalent) to clear any previous content on the screen.
  • Drawing Text and Graphics: Use the library's functions to draw pixels, lines, rectangles, circles, and display text. Common functions include `drawPixel(x, y, color)`, `setTextSize(size)`, `setTextColor(color)`, `setCursor(x, y)`, and `print("Hello World")`.
  • Updating the Display: After drawing, call `display()` (or equivalent) to push the buffer content to the physical screen. The display does not update automatically after each drawing command.
  • Backlight Control: If your module has controllable backlight pins, you can turn the backlight on/off or adjust its brightness (if supported) via your microcontroller's digital output pins.

5. Maintenance

To ensure the longevity and optimal performance of your LCD module:

  • Handle with Care: Avoid applying excessive pressure to the display surface.
  • Cleanliness: Use a soft, lint-free cloth to gently wipe the screen. Do not use abrasive cleaners or solvents.
  • Storage: Store the module in a dry, anti-static environment, away from direct sunlight and extreme temperatures. Refer to the storage temperature range in Figure 2 (-30°C to 80°C).
  • Power Supply: Ensure a stable power supply within the recommended voltage range to prevent damage.
Comparison of LCD modules with and without a protective iron frame
Figure 4: Some modules may come with a protective iron frame for added durability.

6. Troubleshooting

If you encounter issues with your LCD module, consider the following:

  • No Display/Blank Screen:
    • Check all wiring connections, especially VCC, GND, SCL, SDA, CS, DC, and RST. Ensure they are secure and correctly connected to your microcontroller.
    • Verify your power supply voltage is correct and stable.
    • Confirm that the display initialization code is running correctly and that the `display()` function is called after drawing.
    • Ensure the backlight (BL) pin is powered if you expect illumination.
  • Garbled or Incorrect Display:
    • Double-check your SPI communication settings (mode, clock speed) in your software.
    • Ensure the correct display library for the ST7567A driver is being used.
    • Verify that the `DC` (Data/Command) pin is being toggled correctly by your library.
    • Check for any loose connections or shorts on the data lines.
  • Partial Display:
    • Ensure your drawing coordinates and buffer sizes match the 128x64 resolution.
    • Confirm that the entire display buffer is being sent to the LCD.

7. User Tips

  • Use Reliable Libraries: For ease of use and robust functionality, always opt for well-documented and community-supported libraries for the ST7567A driver.
  • Test with Simple Code: When troubleshooting, start with a basic

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.