AIFEN A9-2026

Contents

AIFEN A9-2026 Soldering Station User Manual

Model: A9-2026

Safety Attention

When the power is on, the soldering iron tip temperature will be between 100°C-450°C (212°F-842°F). Misuse can lead to burns or fire. Please strictly observe the following instructions:

  • Do not touch the iron tip or any nearby metal parts.
  • Do not use the soldering iron near flammable materials.
  • Inform others in the workspace that the iron tip is hot and can cause accidents.
  • Turn off the power during breaks or after completing work.
  • When replacing parts or adjusting the soldering iron tip, turn off the power and wait for the tip to cool to room temperature.
  • This product uses rated voltage and frequency. Refer to the label on the back of the machine for details.
  • It is strictly prohibited to use this product if it is damaged, especially if the power cable is compromised.
  • This product uses a three-wire grounding plug and must be inserted into a three-hole grounded socket. Do not modify the plug or use ungrounded adapters. If an extension cord is needed, use a grounded three-wire power cord.
  • Do not use the soldering iron for any purpose other than welding.
  • Do not tap the soldering iron tip on the workbench to remove flux residue, as this can severely damage the tip.
  • When replacing components, use original factory parts.
  • Do not modify the soldering iron without authorization.
  • Do not wet the soldering iron, and do not use it with wet hands.
  • Welding produces smoke; ensure adequate ventilation in the work area.
  • Do not harm yourself when using the machine.
  • Children are unaware of the dangers of electrical products. This product should be used and stored in a place inaccessible to children or under adult supervision.

Product Specifications

Specification Value
Input Voltage AC100-240V 50/60Hz
210 Maximum Power 120W (MAX)
245 Maximum Power 180W (MAX)
Temperature Control Range 100°C - 450°C (212°F - 842°F)
Machine Size 157 x 127 x 132 mm
Inner Box Size 235 x 210 x 185 mm
Machine Weight 1.1 kg
Weight of online purchased machine 0.82 kg

Note: The A9ED model only includes a standard controller. The wired controller needs to be purchased separately.

AIFEN A9-2026 Soldering Station specifications table
Detailed specifications for the AIFEN A9-2026 Soldering Station.

Product Components

AIFEN A9-2026 Soldering Station with labeled components
Diagram of the AIFEN A9-2026 Soldering Station with labeled parts.
  • Hub: Main unit of the soldering station.
  • Handle: The soldering iron handle.
  • Handle Button: Buttons on the handle for control.
  • Adjustable Bracket: For holding the soldering iron.
  • Preset Temp Display: Shows the set temperature.
  • Clean Copper Wire Ball: For cleaning soldering tips.
  • Clean Copper Brush: For cleaning soldering tips.
  • Menu Button: For navigating the station's menu.
  • Plug and Unplug Box: Area for quick tip changes.
  • Power Display: Indicates power status.
  • Actual TEMP Display: Shows the current temperature.
  • Memory Display: Shows stored temperature settings.
  • Memory Button: For saving and recalling temperature settings.
  • Temp Setting Button: For adjusting temperature.
  • Heating Core Storage Hole: For storing heating cores.

Setup Instructions

Attention: Always turn off the power when connecting or disconnecting the handle to prevent damage to the control circuit board.

  1. Connect the handle to the handle socket on the main unit.
  2. Install the required heating element into the handle.
  3. Position the soldering station appropriately and place the handle on its holder.
  4. Connect the power supply securely.
  5. Turn on the power switch. The display window will show "sleep", indicating the soldering station is in standby mode.

Operating Instructions

Official product overview video demonstrating key features and operation of the AIFEN A9-2026 Soldering Station.

Temperature Setting and Storage

  • Heating Up: Press the "^" key once to increase the temperature by 1°C. The display will show the set temperature. Hold the "^" key for at least one second for rapid temperature increase until the desired temperature is reached, then release.
  • Cooling Down: Press the "v" key once to decrease the temperature by 1°C. The display will show the set temperature. Hold the "v" key for at least one second for rapid temperature decrease until the desired temperature is reached, then release.
  • Storage: After setting the desired temperature, long press the "CH1", "CH2", "CH3", or "CH4" button to store the setting.
  • Recall: To retrieve stored temperature data, short press "CH1", "CH2", "CH3", or "CH4" (less than 1 second).

Display Mode

  • Short press the OK button to enter the System Settings menu. Navigate to "Display Mode" and select "Curve/Standard Mode". Short press OK to select, then long press OK to exit.

Language Settings

AIFEN A9-2026 Soldering Station with multi-language display settings
The soldering station's display showing available language settings (English, Chinese, Spanish, Russian).
  • Short press the OK button to enter the System Settings menu. Navigate to "Language Settings" and select your desired language. Short press OK to select, then long press OK to exit.

Sound Settings

  • Short press the OK button to enter the System Settings menu. Navigate to "Sound Settings" and select "On/Off". Short press OK to select, then long press OK to exit.

Temperature Unit

  • Short press the OK button to enter the System Settings menu. Navigate to "Temperature Unit" and select "°C/°F". Short press OK to select, then long press OK to exit.

Temperature Calibration

  • Short press the OK button to enter the System Settings menu. Navigate to "Temperature Calibration" and adjust the temperature by ±99°C. Short press OK to select, then long press OK to exit.

Sleep Temperature

  • Short press the OK button to enter the System Settings menu. Navigate to "Sleep Temperature" and select a value between 50°C-200°C. Short press OK to select, then long press OK to exit.

Brightness

  • Short press the OK button to enter the System Settings menu. Navigate to "Brightness" and select a value between 10-100 (default is 50). Short press OK to select, then long press OK to exit.

Key Doubling Speed

  • Short press the OK button to enter the System Settings menu. Navigate to "Key Doubling Speed" and select 1x/5x/10x. Short press OK to select, then long press OK to exit.

Handle Function

  • Short press the OK button to enter the System Settings menu. Navigate to "Handle Function" and select "Temperature/Memory/Off". Short press OK to select, then long press OK to exit.
  • Adjust Temperature: In this mode, use the joystick buttons on the handle to increase or decrease the temperature.
  • Adjusting Memory: In this mode, use the joystick buttons on the handle to navigate and select the corresponding four memory channels on the host.

Forced Sleep

  • Short press the OK button to enter the System Settings menu. Navigate to "Forced Sleep" and select "Allowed/Prohibited". Short press OK to select, then long press OK to exit.
  • Allow Forced Hibernation: In this mode, press and hold the temperature up and down buttons on the controller simultaneously to enter/exit the forced sleep interface.

Key Lock

  • Short press the OK button to enter the System Settings menu. Navigate to "Key Lock" and select "On/Off". Short press OK to select, then long press OK to exit.

Trigger Temperature

  • After turning off the host, press and hold the CH3 button and then turn on the host to enter the setting interface. Use the temperature buttons to set the parameters. After setting, press the OK button to exit.
  • Warning: The trigger temperature is the compensation temperature, ranging from 0-50°C. A higher trigger temperature makes the heating core more susceptible to damage. It is recommended to use a common temperature range of 330-360°C. Non-professionals should not adjust the trigger temperature value.
AIFEN A9-2026 Soldering Station showing quick plug and unplug of soldering tips
Demonstration of quick plug and unplug functionality for soldering tips.

Maintenance and Upkeep

Temperature of Soldering Iron Tip

Excessive temperature can weaken the function of the soldering iron tip. Therefore, the lowest possible temperature should be chosen for effective soldering. This soldering iron tip offers excellent temperature recovery, allowing for complete soldering at lower temperatures to protect temperature-sensitive components.

Cleaning

Copper wire cleaning balls or copper brushes should be used regularly to clean the soldering iron tip. After welding, residual flux-derived oxides and carbides can damage the soldering iron tip, causing welding errors or reducing its thermal conductivity.

After Use

After use, the soldering iron tip should be wiped clean and coated with a new layer of tin to prevent oxidation.

Repair

Caution: Do not use a file to remove any vapors from the soldering iron tip.

  1. Set the temperature to 250°C (482°F).
  2. After the temperature stabilizes, use a copper wire ball or copper brush to clean the soldering iron tip.
  3. After thoroughly removing any oxide, apply a new tin layer.
  4. If the soldering iron tip is deformed or heavily rusted, a new heating element must be replaced.

Replacement of Heating Element

This soldering station uses a heating element integrated with the soldering head. To replace it, turn off the power and allow the unit to cool to room temperature. Then, remove the old heating element and insert the new one.

Troubleshooting

Error Codes and Indicators

  • "No Tools" Error: If the heating element of the soldering station burns out, breaks, or is not properly placed in the handle, the station will display "No tools" and emit an intermittent buzzing sound.
  • "Short Circuit" Error: If the heating element short circuits, the station will display "short circuit" and emit an uninterrupted buzzing sound. In this case, remove the short-circuited heating element and turn off the main power. After 1 minute, the machine can be restored by turning it back on.

User Tips

  • Fast Heating: Users report that the station heats up in just 2-3 seconds, making it very efficient for quick tasks.
  • Stable Temperature Control: The temperature control on the handle is highly effective and stable, ensuring consistent performance.
  • Quick Tip Changes: The quick change mechanism for soldering tips is a significant convenience feature.
  • Versatile Compatibility: The station is compatible with 210, 245, and 115 handles, offering flexibility for various soldering needs.
  • Secure Packaging: Products typically arrive well-protected in their original box with high-quality protective foam, ensuring items are in perfect condition upon arrival.

Warranty and Support

For any warranty claims, technical support, or service inquiries, please contact the original seller or authorized distributor. Keep your purchase receipt as proof of purchase.

Additional Resources

A comprehensive user manual in PDF format is available for download. This document contains detailed diagrams and further information regarding the operation and maintenance of your AIFEN A9-2026 Soldering Station.

You can access the PDF manual here: AIFEN A9-2026 User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.