HGLRC H743 8S MINI V1

Contents

HGLRC H743 8S MINI V1 Flight Controller & 60A 4IN1 6S 8bit ESC User Manual

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your HGLRC H743 8S MINI V1 Flight Controller (FC) and HGLRC 60A 4-in-1 6S 8-bit Mini V1 Electronic Speed Controller (ESC). These components are designed for high-performance FPV racing drones, offering stable control and powerful output in a compact form factor.

2. Specifications

2.1 HGLRC H743 8S MINI V1 Flight Controller

FeatureSpecification
Model NameHGLRC H743 8S MINI V1
FC FirmwareHGLRC_H743_LITE
MCUSTM32H743
GyroscopeICM42688P
OSDAT7456E
BarometerSPA06-003
Blackbox16MB
UART Ports8
Input Voltage7.4V-33.6V (2-8S LiPo)
Dimensions42mm x 25mm
Mounting Holes20mm x 20mm, M3
Weight6.8g

2.2 HGLRC 60A 4-in-1 6S 8-bit Mini V1 ESC

FeatureSpecification
Product NameHGLRC 60A 4IN1 6S 8-bit MINI V1 ESC
Input Voltage7.4V-25.2V (2S-6S LiPo)
Operating Current60A per channel rated
ESC FirmwareM-H-30
Dimensions57mm x 33mm
Mounting Holes20mm x 20mm, M3
Weight13.9g
Digital ProtocolsSupports DShot600/300

3. Package Contents

3.1 HGLRC H743 8S MINI V1 Flight Controller Package

  • 1x HGLRC H743 8S MINI V1 FC
  • 1x 30AWG 25mm Double-ended SH1.0-8P Cable
  • 1x 30AWG 100mm Double-ended SH1.0-4P Receiver Cable
  • 1x 30AWG 50mm Single SH1.0-3P / Single SH1.25-3P Camera Cable
  • 1x 30AWG 70mm Single GH1.25-6P / Single SH1.0-7P DJI Cable
  • 1x 30AWG 70mm Single SH1.0-7P / Single 1.0-6P VTX Cable
  • 1x 30AWG 120mm Double-ended SH1.0-6P GPS Cable
  • 4x 3*8 Vibration Damping Standoffs
  • 4x 3*6.6 Vibration Damping Standoffs
  • 1x HGLRC Sticker
  • 1x QR Code Card

3.2 HGLRC 60A 4-in-1 6S 8-bit Mini V1 ESC Package

  • 1x HGLRC 60A 4-in-1 16S 8-bit Mini V1 ESC
  • 1x 30AWG 25mm Dual-End SH1.0-8P Cable
  • 1x 12AWG 100mm Power Cable (Black/Red)
  • 1x XT60H-M Black Male Connector
  • 1x 35V 1000UF Solid Capacitor
  • 4x 3*8 Shock-Absorbing Pillars
  • 4x 3*6.6 Shock Absorber Column
  • 1x "Huagulong" 2025 Model Small Sticker
  • 1x QR Code Card

4. Setup

4.1 Mounting

Both the FC and ESC feature 20mm x 20mm mounting holes with M3 diameter. Use the provided vibration damping standoffs to securely mount the FC and ESC to your drone frame. Ensure proper orientation as indicated by the arrow on the FC board.

4.2 Wiring Diagram

The HGLRC H743 8S MINI V1 FC and 60A 4-in-1 6S 8-bit Mini V1 ESC are designed for modular plug-and-play connection. Refer to the detailed wiring diagram below for connecting the FC to the ESC, motors, battery, and other peripherals.

HGLRC H743 8S MINI V1 FC and 60A 4-in-1 ESC Wiring Diagram
Figure 1: Main Wiring Diagram. This diagram illustrates the connection between the HGLRC H743 8S MINI V1 Flight Controller (top), the HGLRC 60A 4-in-1 ESC (middle), four motors, and the main battery (bottom). The FC connects to the ESC via the provided 8-pin cable. Motor outputs M1-M4 from the ESC connect to the respective motors. The main battery connects to the ESC's positive (+) and negative (-) terminals.
HGLRC H743 8S MINI V1 FC and 60A 4-in-1 ESC Detailed Overview and Wiring
Figure 2: Detailed Product Overview and Wiring. This comprehensive image provides a detailed breakdown of both the Flight Controller and ESC. It includes:
  • Flight Controller Features: High-performance STM32H743 MCU, ICM42688P gyroscope, 16MB Blackbox, 8S high-voltage input, fully modular design, ultra-narrow size, and dual BEC.
  • FC Pinout Diagram: Labels for all FC pads including 5V, GND, UARTs (TX1-TX8, RX1-RX8), SCL, SDA, 10V, VOUT, SYNC, GYRO, LED, BB-, BB+, BAT, CUR, SSS.
  • ESC Pinout Diagram: Labels for motor outputs M1-M4 and battery input.
  • Combined Wiring Diagram: Illustrates the connection flow from FC to ESC, motors, and battery.
  • Specifications: Detailed specifications for the FC.
  • Dimensions: Physical dimensions of the FC.
  • Product List: Contents included with the FC.

4.3 Peripheral Connections

Connect your receiver, VTX, camera, GPS, and other peripherals to the appropriate UART ports and power pads on the flight controller as per the wiring diagrams and your specific peripheral requirements. Ensure correct voltage supply for each component (e.g., 5V, 10V).

5. Operating

Once physically installed and wired, the flight controller requires configuration using Betaflight Configurator or similar software. Connect the FC to your computer via USB. Ensure the correct firmware (HGLRC_H743_LITE) is flashed. Configure your receiver, ESC protocols (DShot600/300), OSD, and other settings according to your preferences and drone setup.

The ESC supports DShot600/300 digital protocols, providing precise motor control. Ensure your flight controller is configured to use the appropriate DShot protocol for optimal performance.

6. Maintenance

  • Regularly inspect all solder joints and cable connections for any signs of wear or damage.
  • Keep the FC and ESC clean from dust, dirt, and moisture. Use compressed air or a soft brush for cleaning.
  • Avoid exposing the components to extreme temperatures or direct sunlight for prolonged periods.
  • Ensure proper airflow around the ESC during operation to prevent overheating.

7. Troubleshooting

  • No Power to FC/ESC: Check main battery connection, XT60 connector, and ensure no short circuits. Verify power cables are correctly soldered.
  • Motors Not Spinning: Check ESC to FC connection, motor wiring, and ESC calibration in Betaflight. Ensure correct DShot protocol is selected.
  • Peripherals Not Working (e.g., Camera, Receiver): Verify power and signal connections to the FC. Ensure the correct UART is enabled and configured in Betaflight. Check voltage output from FC power pads (5V, 10V) to ensure they are supplying power.
  • Unstable Flight: Check gyroscope orientation in Betaflight, motor direction, and propeller direction. Ensure all mounting screws are tight and vibration damping is effective.
  • FC Not Connecting to PC: Try a different USB cable and port. Ensure Betaflight Configurator is up to date. Install necessary STM32 drivers if prompted.

8. User Tips

  • When connecting peripherals like DJI O4 Pro cameras or TBS Crossfire receivers, always double-check the power output from the FC (e.g., 5V, 10V) and ensure the peripheral's voltage requirements match. Incorrect voltage or insufficient current can prevent them from powering on.
  • Utilize the 16MB Blackbox logging feature to record flight data. This data is invaluable for diagnosing flight performance issues and tuning your drone.
  • Always perform a dry run (without propellers) after any wiring changes or firmware updates to ensure all motors spin correctly and in the right direction.

9. Warranty and Support

For warranty information and technical support, please refer to the official HGLRC website or contact your retailer. Keep your proof of purchase for any warranty claims.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.