ZIBOO 15B PRO / 17B PRO

Contents

ZIBOO 15B PRO / 17B PRO True RMS Digital Multimeter User Manual

Models: 15B PRO, 17B PRO

1. Introduction and Safety Information

This manual provides essential information for the safe and effective operation, maintenance, and troubleshooting of your ZIBOO 15B PRO or 17B PRO True RMS Digital Multimeter. Please read this manual thoroughly before use and keep it for future reference.

1.1 Safety Information

This product strictly adheres to the safety standards of European Electrotechnical Commission EN61010-1 and China GB T 13978. Adherence to these guidelines is crucial for safe operation.

  • Always read the safety information before using the instrument and operate in strict accordance with the provisions.
  • Measure according to the specified range and do not rotate the gear during measurement to avoid damage.
  • To avoid possible electrical shock, do not touch live conductors exceeding 30V AC and 60V DC during measurement.
  • When measuring AC and DC over 599V, a high voltage lightning symbol will display, and the buzzer will beep. Exercise extreme caution.
  • Do not use the multimeter in flammable and explosive environments.
  • If the meter displays a low battery symbol, replace the battery immediately to avoid measurement errors.
  • Before measuring, check test leads and wires for damage or leakage. Do not use if damaged.
  • Comply with national regulations and measurement safety standards. Wear insulating gloves or flame-retardant products when measuring hazardous voltage.

1.2 International Electrical Symbols

SymbolExplanation
Be careful! Indicates a dangerous operationBe careful! Indicates a dangerous operation
High current! Indicates a high voltage hazard warningHigh current! Indicates a high voltage hazard warning
CE MarkEuropean Union unified directive, European CE certification
Grounding symbolGrounding
Double insulation or enhanced insulation protectionDouble insulation or enhanced insulation protection
WEEE recycling instructions complianceCompliance with WEEE recycling instructions

2. Product Overview

The ZIBOO 15B PRO and 17B PRO are new technology digital multimeters featuring a two-color protective cover, hand-held non-slip ergonomic design, and a large-screen LCD display. They offer multi-functionality, high precision, high performance, anti-drop durability, safety, and stability. These multimeters can accurately measure AC/DC voltage, AC/DC current, frequency, continuity, diode, resistance, capacitance, and include high voltage alarm, NCV (Non-Contact Voltage) and Live wire detection. They also feature misoperation circuit protection, making them suitable for professional electricians, electronic technology maintenance and repair, and DIY electronics enthusiasts.

The 17B PRO model extends DC Voltage measurement up to 1500V.

Video: Demonstration of ZIBOO 17B PRO Multimeter features including NCV, short-circuit test, AC current test, capacitance test, resistance test, AC voltage test, backlight function, and DC voltage test.

3. Key Features and Functions

Both ZIBOO 15B PRO and 17B PRO models offer a comprehensive set of features:

  • Safety Rating: CAT III 600V (and CAT II 1000V for 15B PRO, CAT III 600V for 17B PRO) ensuring safety in residential, commercial, and industrial settings.
  • Voltage Measurement: AC/DC Voltage up to 1000V (15B PRO) / 1500V (17B PRO).
  • Current Measurement: AC/DC Current up to 10A. Optional AC 600A current clamp support.
  • Resistance: Measures up to 60MΩ.
  • Continuity: Buzzer with green LED flash for quick continuity checks.
  • Capacitance: Measures a wide range of capacitance values.
  • Diode Test: Quickly identifies faulty diodes.
  • Frequency: Measures frequency up to 400kHz.
  • Temperature Measurement (17B PRO only): Up to 1000°C with included Type K thermocouple.
  • True RMS: Accurate readings for non-sinusoidal waveforms.
  • VFD AC 600V (Variable Frequency Drive): For accurate measurements on VFD circuits.
  • NCV (Non-Contact Voltage) / LIVE: Red LED flash and buzzing sound for non-contact voltage detection and live wire identification.
  • Data Hold: Freezes the display for easier recording.
  • Backlight: Bright white backlight for visibility in all lighting conditions.
  • 6000 Counts Display: High resolution for precise readings.
  • Auto Ranging: Automatically selects the correct measurement range.
  • Intelligent Anti-Burning: Built-in double fuse with overload protection to prevent operational errors from damaging the meter.

3.1 Description of Appearance

ZIBOO 15B PRO Multimeter product size dimensions: 18.3cm/7.2 inches height, 9.1cm/3.58 inches width, 4.5cm/1.77 inches depth.

Image: Front and back view of the ZIBOO 15B PRO Multimeter with dimensions.

ZIBOO 15B PRO Multimeter with test leads, showing the main display, rotary dial, function buttons, and input jacks.

Image: ZIBOO 15B PRO Multimeter with test leads.

ZIBOO 17B PRO Multimeter with test leads, showing the main display, rotary dial, function buttons, and input jacks.

Image: ZIBOO 17B PRO Multimeter with test leads.

The multimeter features a large LCD display, a central rotary dial for function selection, and several push buttons for additional features. Input jacks are located at the bottom for test leads.

3.2 LCD Display and Symbols

The LCD displays measurement readings, units, and various symbols indicating the current mode or status.

NumberSymbolExplanation
1OFFTurn off the power
2Auto power-off symbolAuto power-off
3Low battery indication symbolLow battery indication
4mVDC millivolt
5TRUE RMSTrue RMS measurement
6V~AC voltage
7HzFrequency
8uA, mA, ADC microampere, milliampere, ampere
9uA~, mA~, A~AC microampere, milliampere, ampere
10Ω, KΩ, MΩResistance Ohm, Kiloohm, Megaohm
11Continuity beeper and Diode symbolContinuity beeper, Diode
12nF, uF, mFCapacitance nanofarad, microfarad, millifarad
13RELClear the relative value
14Battery 1.5V 9V symbolBattery 1.5V 9V
15NCV EFNon-contact sensing signal
16LIVEAC Live wire detection
17°C/°FTemperature (17B PRO only)
18Current Clamp symbolCurrent Clamp
19VFDAC variable frequency measurement

4. Technical Specifications

4.1 General Technical Indicators

  • Maximum Display: 6000 counts
  • Sampling Rate: 3 times/second
  • Overload Display: "OL"
  • Auto Power Off: Approximately 15 minutes
  • Precision: 23°C ± 5°C (18-28°C; Humidity <75%); 1 year
  • Operating Temperature: 0°C to 40°C
  • Storage Temperature: -10°C to 60°C
  • Storage Humidity: ≤80%
  • Altitude: 0-2000m
  • Pollution Grade: 2
  • Safety Codes: CE EN61010-1-2-030
  • Electromagnetic Environment: EN61326-1-2
  • Power: AA 1.5V x 3 batteries
  • Dimensions: 183 x 91 x 45mm
  • Weight: 402g (including battery)

4.2 Measurement Ranges and Accuracy

FunctionRange (15B PRO)Range (17B PRO)ResolutionAccuracy
DC Voltage (DCV)60.00mV, 600.0mV, 6.000V, 60.00V, 600.0V, 1000V60.00mV, 600.0mV, 6.000V, 60.00V, 600.0V, 1500V0.01mV to 1V±(0.5%+3) to ±(0.8%+5)
AC Voltage (ACV)6.000V, 60.00V, 600.0V, 1000V6.000V, 60.00V, 600.0V, 1000V0.001V to 1V±(0.8%+5) to ±(1.2%+5) (400Hz, 1KHz)
Frequency (Hz)10.00Hz, 100.0Hz, 1.000KHz, 60KHz10.00Hz, 100.0Hz, 1.000KHz, 60KHz0.01Hz to 0.01KHz±(0.5%+5)
Resistance (Ω)600.0Ω, 6.000KΩ, 60.00KΩ, 600.0KΩ, 6.000MΩ, 60.00MΩ600.0Ω, 6.000KΩ, 60.00KΩ, 600.0KΩ, 6.000MΩ, 60.00MΩ0.1Ω to 0.01MΩ±(1%+5) to ±(2.5%+5)
Capacitance6.000nF, 60.00nF, 600.0nF, 6.000uF, 600.0uF, 6000uF6.000nF, 60.00nF, 600.0nF, 6.000uF, 600.0uF, 60000uF0.001nF to 0.1mF±(1.5%+5) to ±(8%+5)
DC Current (DCA)600.0uA, 6.000mA, 60.00mA, 600.0mA, 6.000A, 10.00A600.0uA, 6.000mA, 60.00mA, 600.0mA, 6.000A, 10.00A0.1uA to 0.01A±(0.8%+5) to ±(2%+5)
AC Current (ACA)600.0uA, 6.000mA, 60.00mA, 600.0mA, 6.000A, 10.00A600.0uA, 6.000mA, 60.00mA, 600.0mA, 6.000A, 10.00A0.1uA to 0.01A±(1%+5) to ±(2%+5) (1KHz)
Temperature (°C/°F) (17B PRO only)N/A-50°C to 1000°C, -58°F to 1832°F1°C / 1°F±(1.5%+4) to ±(2%+5)
Continuity / DiodeContinuity, DiodeContinuity, DiodeN/A0.500V-0.800V (Diode)
NCV / LIVE50V-1000V50V-1000VN/A0-5cm (Non-contact induction)
Current Clamp60.0A, 600.0A (AC/DC)60.0A, 600.0A (AC/DC)0.1A±(3%+5)

5. Initial Setup

5.1 Battery Installation

The ZIBOO multimeter requires 3x AA 1.5V batteries (LR06-AA). Batteries are not included and must be installed before first use.

  1. Ensure the multimeter is turned OFF and disconnect all test leads from the circuit and the meter.
  2. Locate the battery cover on the back of the multimeter.
  3. Unscrew the retaining screw(s) on the battery cover.
  4. Remove the battery cover.
  5. Insert three AA 1.5V batteries, observing the correct polarity (+/-) as indicated inside the battery compartment.
  6. Replace the battery cover and securely fasten the screw(s).

Note: After replacing the battery, ensure that the battery cover is tightly screwed before the meter can be used normally.

Internal view of the ZIBOO multimeter showing the battery compartment and fuses.

Image: Internal view showing battery compartment and fuses.

6. Operating Instructions

To operate the multimeter, select the desired function using the rotary dial and connect the test leads appropriately. The meter features auto-ranging for most functions, simplifying operation.

6.1 Connecting Test Leads

  • For most voltage, resistance, continuity, diode, and capacitance measurements, connect the red test lead to the "VΩmA" jack and the black test lead to the "COM" jack.
  • For high current (up to 10A) measurements, connect the red test lead to the "10A" jack and the black test lead to the "COM" jack.
  • For current clamp measurements, connect the current clamp output to the appropriate jacks as per the clamp's instructions (typically "VΩmA" or "Hz" for signal output).

6.2 Measurement Functions

Turn the rotary dial to the desired measurement function. Use the MODE button to cycle through sub-functions if available (e.g., AC/DC for voltage/current, diode/continuity).

  • DC Voltage (DCV): Select the "V" position on the dial. The meter will automatically detect DC voltage. Connect leads in parallel with the DC source.
  • AC Voltage (ACV): Select the "V~" position on the dial. The meter will automatically detect AC voltage. Connect leads in parallel with the AC source.
  • Resistance (Ω): Select the "Ω" position. Connect leads across the component.
  • Continuity: Select the "Ω" position and press MODE until the continuity symbol appears. A buzzer sounds for low resistance.
  • Diode Test: Select the "Ω" position and press MODE until the diode symbol appears. Connect leads across the diode.
  • Capacitance: Select the "nF" position. Connect leads across the capacitor.
  • DC Current (DCA): Select the "uA/mA" or "A" position. Connect leads in series with the DC circuit.
  • AC Current (ACA): Select the "uA/mA~" or "A~" position. Connect leads in series with the AC circuit.
  • Frequency (Hz): Select the "Hz" position. Connect leads across the signal source.
  • Temperature (°C/°F) (17B PRO only): Select the "°C/°F" position. Connect the thermocouple to the appropriate jacks.
  • NCV (Non-Contact Voltage): Select the "NCV" position. Bring the top of the meter near a live conductor.
  • LIVE Wire Detection: Select the "LIVE" position. Use the red probe to touch the suspected live wire.
  • VFD (Variable Frequency Drive): Press and hold the MODE button for 3 seconds to activate VFD mode when in AC voltage measurement.

6.3 Button Functions

  • HOLD: Short press to freeze the current reading on the display. Press again to release.
  • RANGE: Press to switch between auto-ranging and manual ranging. In manual mode, press repeatedly to cycle through ranges.
  • MAX/MIN: Press to record maximum and minimum values during a measurement.
  • MODE: Press to switch between different sub-functions within a rotary dial position (e.g., AC/DC, Diode/Continuity).
  • VFD: Long press MODE to activate VFD mode.
  • Backlight (*): Press the backlight button to turn on the display backlight. The backlight automatically turns off after approximately 30 seconds.
ZIBOO 15B PRO Multimeter measuring DC voltage on a battery.

Image: Measuring DC voltage.

ZIBOO 15B PRO Multimeter measuring AC current with an optional clamp meter.

Image: Measuring AC current with an optional clamp meter.

ZIBOO 15B PRO Multimeter measuring resistance of a component.

Image: Measuring resistance.

ZIBOO 15B PRO Multimeter measuring capacitance of a capacitor.

Image: Measuring capacitance.

ZIBOO 15B PRO Multimeter demonstrating NCV (Non-Contact Voltage) detection near an electrical outlet.

Image: Demonstrating NCV function.

7. Maintenance

7.1 Replacing Fuses

To avoid electric shock, disconnect the test leads from the circuit and the meter before replacing fuses.

  • Fuse Specification (15B PRO / 17B PRO):
    • F1: 500mA/1000V, 6.3x31.5mm
    • F2: 10A/1000V, 6.3x31.5mm

The fuses are located inside the meter, accessible after removing the battery cover and potentially additional screws. It is recommended that fuse replacement be performed by a qualified technician.

7.2 Replacing Batteries

To avoid electric shock, disconnect the test leads from the circuit and the meter before replacing batteries.

  • Battery Specification: LR06-AA 1.5V x 3

Follow the steps in Section 5.1 "Battery Installation" to replace the batteries.

7.3 Repair and Service

Any repairs requiring the opening of the meter's cover should only be performed by an approved and professionally experienced technician. Improper maintenance can lead to damage to the instrument or risk of electric shock. If a fault cannot be resolved, please contact ZIBOO official after-sales service.

Contact Information:
E-Mail: sales-support@ziboo.online

8. Troubleshooting

If you encounter issues with your ZIBOO multimeter, refer to the following common problems and solutions:

  • Meter does not turn on:
    - Check if the batteries are installed correctly with the right polarity.
    - Replace the batteries if they are depleted.
  • Inaccurate readings:
    - Ensure the correct function is selected on the rotary dial.
    - Check if the test leads are fully inserted and not damaged.
    - Replace batteries if the low battery indicator is on.
    - Ensure the measurement range is appropriate (though auto-ranging handles most cases).
  • No continuity beep:
    - Ensure the meter is in continuity mode (check display symbol).
    - Check test leads for breaks or poor connection.
  • No display or "OL" (Overload) displayed:
    - "OL" indicates the measurement exceeds the selected range or the maximum capability of the meter. Switch to a higher range if in manual mode, or ensure the input is within the meter's limits.
    - If no display, check battery and power.
  • Fuse blown during current measurement:
    - This usually happens if the meter was connected in parallel for current measurement or if the current exceeded the fuse rating. Always connect in series for current measurement and ensure the expected current is within the meter's limits. Replace the appropriate fuse (see Section 7.1).

9. User Tips

  • Accuracy: Users report excellent calibration and accuracy, often comparable to higher-end brands like Fluke. The ZIBOO multimeters are noted for being very precise and reliable.
  • Build Quality: The meters are well-built with good internal protection, including ceramic fuses, MOVs, and quality resistors, providing enhanced safety. The rotary switch is described as chunky and sturdy.
  • Display: Features a large, bright, and easy-to-read display with a white backlight. Note that the backlight typically stays on for about 30 seconds before automatically turning off to conserve battery.
  • Test Leads: While the included test leads are decent, some users suggest upgrading to silicone test leads for better flexibility and durability.
  • Battery Compatibility: The meter can operate with three rechargeable NiMh AA batteries.
  • Capacitance Measurement: Noted for fast capacitance measurement.
  • Portability: The meter is described as robust and suitable for on-the-go electrical system testing.

10. Warranty and Support

For warranty claims, technical support, or any product-related inquiries, please contact ZIBOO customer service directly.

Contact Information:
E-Mail: sales-support@ziboo.online

For additional guides and documents, you may refer to the official PDF user manual available at: ZIBOO Digital Multimeter User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.