1. General Information
The VDIAGTOOL VD31 is a multifunctional code reader designed to assist in vehicle diagnostics. It supports On-Board Diagnostics (OBD) II, which continuously or periodically monitors emission control systems and critical engine components. When an issue is detected, the system activates a Malfunction Indicator Light (MIL) on the dashboard, commonly known as the "Check Engine" light.
Key information provided by the device includes:
- MIL Status: Indicates whether the warning light is activated ("on") or deactivated ("off").
- Diagnostic Trouble Codes (DTCs): Specific error codes stored in the system.
- Readiness Monitor Status: Shows the completion status of emission-related self-tests.
1.1 Diagnostic Trouble Codes (DTCs)
DTCs are alphanumeric codes stored by the vehicle's OBD II system when a malfunction is detected. These codes help pinpoint the source of a problem. An OBD II DTC follows a 5-character format:
- First character (letter): Indicates the affected system:
- P = Powertrain (Engine/Transmission)
- B = Body (e.g., Airbags, Climate Control)
- C = Chassis (e.g., ABS, Stability Control)
- U = Network/Communication (e.g., CAN Bus)
- Remaining four digits: Specify the exact issue.
Figure 1: DTC Lookup interface for instant code explanations.
1.2 Location of the Data Link Connector (DLC)
The Data Link Connector (DLC) is a standardized 16-pin port used to connect diagnostic scan tools to your vehicle's onboard computer.
Typical DLC Locations:
- Most vehicles: Within 12 inches of the dashboard center, typically under or near the driver's side.
- Some Asian/European models: Behind the ashtray (may require removal for access).
- If not visible, check for a location label or consult your vehicle's service manual.
Figure 2: Common locations for the Data Link Connector (DLC).
2. Setup
2.1 Included Accessories
Your VDIAGTOOL VD31 package includes:
- Type-C Cable: For computer connection and firmware updates.
- User Manual: This complete operation instruction guide.
2.2 Power Connection Methods
The VD31 code reader can be powered in several ways:
Vehicle Power Connection (Recommended)
- Locate the vehicle's DLC (typically under the dashboard).
- With the ignition ON, connect the code reader to the DLC.
- The device will auto-power on.
Important: Never use Type-C power during vehicle communication.
Ensure clean connector contact for reliable operation.
Computer Connection (For Updates/Data Transfer)
- Connect the Type-C cable to the device and computer.
- The device will auto-power on.
Built-in 9V Battery (For Key Battery Check Only)
- Insert a fresh 9V battery into the compartment.
- The device will auto-power on when the battery is installed.
2.3 Application Overview
Upon startup, the VD31 displays a main menu with the following preloaded applications:
- OBDII/EOBD: Accesses all nine OBD system tests.
- Battery: Displays the voltage of the vehicle battery.
- Key Battery: Tests and displays the vehicle key fob battery level.
- DTC Lookup: Provides access to the diagnostic trouble code database.
- Review: Allows access to tested data files.
- Print: Accesses the printing function.
- Setting: Modifies device settings such as Language, Unit of Measure, etc.
3. Operating Instructions
3.1 Control Buttons
The VD31 device features several control buttons for navigation and function selection:
Figure 3: VDIAGTOOL VD31 device with its control buttons and screen.
- ESC button: Returns to the previous screen. Press once to exit other tests.
- Up button: Navigates menus upwards, moves to the previous page in multi-screen info, and edits DTC characters.
- Power button: Short press to power on; long press (3 seconds) to power off.
- Left button: Navigates to the previous page in multi-screen info.
- OK button: Confirms selection.
- Right button: Navigates to the next page in multi-screen info.
- I/M button: Checks emissions readiness and drive cycle status.
- Down button: Navigates menus downwards, moves to the next page in multi-screen info, and edits DTC characters.
- Key Battery button: Direct access to key battery voltage measurement.
3.2 OBDII/EOBD Functions
When you select the OBDII/EOBD application from the home screen, your vehicle's diagnostic information will display. Press OK to access the diagnostic menu with the following tests:
- Read DTC
- Clear DTC
- Live Data
- Freeze Frame
- MIL Status
- Vehicle Info
- O2 Sensor
- Mode 6 (On-Board Monitoring)
- Mode 8 (EVAP System Test)
- I/M Readiness
3.2.1 Read DTC
This function allows you to check stored fault codes in the vehicle's control modules. Available code types include Stored DTCs, Pending DTCs, Permanent DTCs, and Record DTCs.
- Stored DTCs: Active fault codes that illuminate the Check Engine Light (MIL). Can be cleared.
- Pending DTCs: Temporary fault codes that do not immediately turn on the MIL. They become confirmed if the problem recurs.
- Permanent DTCs: Fault codes that remain stored even after the MIL turns off, indicating a severe issue. They clear only after the issue is repaired and the system completes 3 consecutive drive cycles without detecting the fault.
- Record DTC: Allows recording of DTCs if trouble codes are present.
To read codes:
- Select "Read DTC" from the OBDII/EOBD menu using the arrow keys, then press OK.
- Choose the code type (Stored, Pending, or Permanent DTCs) and confirm with OK.
- The tool will display all detected codes along with their descriptions.
3.2.2 Clear DTC
This function clears stored diagnostic trouble codes (DTCs) from the vehicle's ECU with the ignition ON (engine OFF).
To erase codes:
- Select "Clear DTC" from the OBDII menu.
- Follow the on-screen prompts to confirm and complete the erasure.
- Immediately rescan the system to check for remaining codes.
After Erasure: If codes persist, it may indicate permanent DTCs. Repair or replace affected components before attempting to clear again.
Figure 4: Clearing the Check Engine Light with VD31.
3.2.3 Live Data
This function allows real-time monitoring of vehicle sensor data and system parameters (PIDs) from the ECU. Options include:
- View All Items: Displays all available vehicle parameters (engine RPM, coolant temperature, fuel trim, O2 sensor voltages, throttle position, etc.).
- Select Items: Enables focused monitoring of specific parameters.
- View Graphic Items: Displays PID data as a graph.
- Record All: Records PIDs to diagnose intermittent drivability problems.
- Record Select: Records selected PID data.
CAUTION: Always park the vehicle before using the code reader for live data recording. If recording during driving, ensure two occupants are present (one to drive, one to operate the device).
Figure 5: 4-in-1 Live Data Graphing.
3.2.4 Freeze Frame
The Freeze Frame function provides a snapshot of critical vehicle parameters recorded at the moment a fault code was triggered. This helps diagnose intermittent issues by showing exact operating conditions when the problem occurred.
To access freeze frame data:
- Select "Freeze Frame" from the OBDII menu.
- Scroll through recorded parameters using the UP/DOWN button.
- View detailed condition readings for each parameter.
Note: If no data is available, the display will show "No freeze frame data stored."
3.2.5 MIL Status
This function displays detailed information about the Check Engine Light status, run time with the light on, and distance traveled with the light on.
3.2.6 Vehicle Information
Retrieves the vehicle's VIN number, calibration IDs (software versions), and calibration verification numbers (CVNs).
3.2.7 O2 Sensor Test
Opens a menu of tests for checking the integrity of the oxygen sensors. Selecting an option displays pertinent O2S parameters.
3.2.8 On-Board Monitoring (Mode 6)
Useful after servicing or clearing the ECU's memory. It receives test results for emission-related powertrain components and systems that are not continuously monitored for Non-CAN vehicles, and for CAN vehicles, it receives test data for both continuously and non-continuously monitored components.
To request On-board Monitor Test (Mode 6) results:
- Use the UP/DOWN key to highlight "On-board Monitor Test (Mode 6)" from the OBDII/EOBD menu and press the OK key.
- A screen will show the monitor list. Use UP/DOWN to highlight a test group and press OK to view details.
3.2.9 EVAP System Test (Mode 8)
Allows the code reader to control the operation of vehicle components and systems. The EVAP (Evaporative Emission Control System) prevents fuel vapor from escaping into the atmosphere.
Main functions of EVAP system:
- Preventing Fuel Vapor Leakage
- Storing Vapor
- Recycling Vapor
- Monitoring for Leaks
- Improving Fuel Efficiency
Note: Some manufacturers do not allow tools to control vehicle systems. Refer to your vehicle service manual.
3.2.10 I/M Readiness
Indicates the status of a vehicle's on-board diagnostic (OBD) system's readiness to perform emissions testing. Crucial for passing state emissions inspections.
Monitor Status:
- OK: Test completed successfully.
- INC (Incomplete): Test not yet finished (needs more driving).
- N/A (Not Applicable): Monitor not required/supported for your vehicle.
Two types of I/M Readiness tests:
- Since DTCs Cleared: Status of monitors since the last DTCs were cleared.
- This Drive Cycle: Status of monitors since the beginning of the current driving cycle.
To retrieve I/M Readiness Status data by one-click hotkey:
- Press the I/M Readiness hot key on the keypad.
- The screen will display the status. Colored LEDs and a built-in beeper provide visual and audible reminders.
Figure 6: I/M Readiness (Smog Check) screen.
3.3 Battery Voltage Test
This function provides real-time monitoring of your vehicle's battery voltage, helping you determine its health and condition.
Figure 7: Real-time battery voltage display.
3.4 Key Fob Battery Check
The VD31 can test the battery level of your car key fob. The device displays the installed 9V battery level in the top-right corner (for the device itself).
Figure 8: Instant Car Key Battery Tester in action.
3.4.1 Test the New Key
For first-time use, select "Test The New Key" to add the test key.
New Key Identification Methods:
- Brand Selection: For more accurate testing, select your vehicle brand directly. This uses pre-configured frequency data. To use:
- Navigate to "Brand Selection" in the menu.
- Choose your vehicle manufacturer from the list.
- Follow on-screen prompts (e.g., press the key button) to test the battery.
- Automatic Scan:
- Position the key in the device's top-left sensing area (align with signal icon).
- Press the key function button every 3 seconds until a success message appears.
- Frequency Selection:
- Adjust frequency value using UP/DOWN buttons (change digit) and LEFT/RIGHT buttons (move cursor).
- Press OK to confirm when "Scan successful" appears.
3.4.2 Test The Store Key
Successfully tested keys are automatically saved in the stored key menu for future testing, eliminating the need for re-identification.
Note: It is recommended to press the OK button to freeze the reading when the key battery level is read. If the key is accidentally moved, the test result may become 0%. You can place the key close to the sensing area again and press the function key (lock or unlock) to re-display the reading. After pressing OK, press ESC to exit and re-measure if needed.
3.5 DTC Lookup
This function provides instant access to the built-in diagnostic trouble code database, containing both SAE standard and manufacturer-specific code definitions.
To search for DTC definitions:
- Select "DTC Lookup" from the main menu.
- Enter the code using:
- LEFT/RIGHT to navigate character positions.
- UP/DOWN to change digit values.
- OK to confirm.
- View the code definition.
Note: For manufacturer-specific codes (P1xxx/C1xxx/B1xxx/U1xxx), select the vehicle make. If no definition is found, consult the vehicle service manual.
4. Maintenance
4.1 Updating the Code Reader
To ensure your VD31 device has the latest features and vehicle compatibility, regular software updates are recommended.
Update Procedure:
- Download and install the VD31 Update Client from www.vdiagtool.com/support/downloads.
- Launch the VD31 Update Client on your computer.
- With the device powered off, hold the Down button while connecting it to your computer via the USB-C cable until "UPDATE MODE" appears on the device screen.
- In the Update Client software, click "Upgrade" and wait for completion.
4.2 Printing Data
This function transfers saved diagnostic data to your computer as a .txt file for printing.
Printing Procedure:
- Open the VD30 Pro software (or VD31 Update Client) and connect the device to your computer.
- Click "Print" in the software.
- On the device, select the required test results to print and confirm.
- The data will transfer as a .txt file to your computer.
- Click "Open File" in the software to locate and print the report.
Figure 9: Data Printing setup.
4.3 Self Tests
This feature verifies the proper operation of the device's hardware components.
- Keys Test: Checks the functionality of the keypad.
- Select "Key Test" from the Self-Test menu.
- Press any button; the display will show the button name.
- Double-press ESC to exit.
- TFT Test: Checks the functionality of the screen.
- Select "TFT Test".
- Visually inspect for dead pixels and color uniformity.
- Press ESC to complete.
- LED Test: Checks the functionality of the status LEDs.
- Select "LED Test".
- All status LEDs will illuminate sequentially.
- Press ESC to terminate.
5. Troubleshooting
This section provides guidance for common issues and important safety considerations.
5.1 Safety Information and Warnings
To ensure your safety and prevent damage to the device or vehicle, please carefully read and follow all instructions in this manual before use.
DANGER: Indicates an immediately life-threatening hazard.
- Always ventilate the service area when the engine is running, or use a building exhaust removal system if available. Carbon monoxide is odorless and deadly.
WARNING: Indicates a potentially dangerous situation that could result in death or serious injury.
- Always conduct testing in a safe, controlled environment.
- Wear ANSI-approved safety goggles during all operations.
- Keep all objects away from moving or hot engine components.
- Ensure proper ventilation to avoid toxic exhaust fumes.
- Secure the vehicle in PARK (automatic) or NEUTRAL (manual) with the parking brake engaged.
- Place wheel chocks and never leave the vehicle unattended during tests.
- Exercise extreme caution around ignition systems where hazardous voltages are present.
- Maintain an ABC-rated fire extinguisher within immediate reach.
- Never connect/disconnect test equipment with ignition on or engine running.
- Keep all test equipment clean, dry, and free from contaminants.
- Never operate test equipment while driving – focus solely on testing.
- Strictly follow the vehicle service manual's diagnostic procedures.
- Verify full battery charge and secure DLC connections before testing.
- Never place test equipment near the distributor due to EMI risks.
5.2 Common Issues and Solutions
- Persistent DTCs after clearing: If codes reappear immediately after clearing, this indicates an underlying mechanical or electrical issue that needs repair. Address the root cause before attempting to clear codes again.
- Key Fob Battery Test reading 0%: If the key is accidentally moved during testing, the reading may drop to 0%. Reposition the key close to the sensing area and press a function button (lock/unlock) to re-display the reading.
- DTC definition not found: For manufacturer-specific codes, ensure you have selected the correct vehicle make. If still not found, consult your vehicle's service manual.
- I/M Readiness Yellow LED: Indicates a possible problem (pending DTCs or emission monitors not working properly). Check the I/M Readiness screen for details.
- I/M Readiness Red LED: Indicates significant problems with one or more vehicle systems, and the vehicle is not ready for an Emissions Test. Fix the problem before further driving or testing.
6. Specifications
6.1 Technical Specifications
| Feature | Specification |
|---|---|
| Display | 2.8" TFT color |
| Operating Temperature | 0°C to 60°C (32°F to 140°F) |
| Storage Temperature | -20°C to 70°C (-4°F to 158°F) |
| Connection | Wired via main cable |
| Power Source | OBDII port connection, Type-C cable, or built-in 9V battery |
| Compatibility | OBDII & EOBD (12V) vehicles |
| Dimensions | 6.5 × 3.54 × 1.18 inches |
| Weight | 8.47 oz |
| Communication Interface | OBD-II |
| Free Update Period | Lifetime |
| Software Update | Yes |
| Language Support | English, French, German, Italian, Polish, Russian, Spanish |
| Software Version | Latest |
| Hardware Version | 2026 |
| Certification | CE |
| Origin | Mainland China |
Figure 10: Wide vehicle compatibility and multi-language support.
7. User Tips
- Preserve 9V Battery: When not performing key fob battery tests, remove the 9V battery from the device to extend its lifespan.
- Accurate Key Fob Testing: For the most precise key fob battery readings, try to input the exact frequency of your key fob, often found on the key itself or through a quick online search.
- Pre-Smog Check: Utilize the one-click I/M Readiness function before a state inspection to ensure all emission monitors are ready, helping you pass the test on the first try.
- Regular Updates: Periodically check the VDIAGTOOL website for software updates to ensure your device has the latest vehicle compatibility and diagnostic features.
- Keep it Clean: Always keep your VD31 device clean and dry to prevent damage and ensure reliable performance.
8. Warranty & Support
8.1 Limited Three Years Warranty
The VDIAGTOOL VD31 product is warranted against defects in materials and workmanship for three years (36 months) from the date of delivery to the buyer. This warranty is expressly limited to buyers who purchase the product for resale or use in the ordinary course of business.
This warranty does not cover any part that has been abused, altered, used for a purpose other than for which it was intended, or used in a manner inconsistent with instructions regarding use. The exclusive remedy for any tool found to be defective is repair or replacement. VDIAGTOOL shall not be liable for any consequential or incidental damages.
8.2 Contact Us
For warranty and support inquiries:
- Email: support@vdiagtool.com
- Website: www.vdiagtool.com
For wholesale business or to become a distributor:
- Email: sales@vdiagtool.com
To invent with us, test products, and help make better products:
- Email: inventers@vdiagtool.com
To create social media content, post online, and help our community:
- Email: marketing@vdiagtool.com
Follow Us on Social Media:
- Facebook Page: Search for "vdiagtool"
- Facebook User Group: Search for "VDIAGTOOL OFFICIAL User Group"
- Instagram: Search for "vdiagtool_official"
- TikTok: Search for "vdiagtool_us"
- YouTube: Search for "Vdiagtool Official"