1. Product Overview
The ZoeRax RJ45 CAT7 CAT6A Crimper Kit is a comprehensive toolset designed for efficient and reliable termination of network cables. It includes a multi-function crimping tool, pass-through RJ45 connectors, and strain relief boots, suitable for both stranded and solid cables.

2. Packing List
Verify that all components are present in your kit:
- Multi-function CAT7 CAT6A Crimping Tool
- Blades (replacement)
- Mini Wire Stripper
- 10PCS RJ45 CAT7 CAT6A Pass Through Connectors
- 10PCS Strain Relief Boots
- Protective Carrying Case

3. Tool Features
The multi-function crimping tool integrates several capabilities for efficient network cable preparation:
- RJ45/12 Crimping: For standard Ethernet connectors.
- UTP/STP Adjuster: For precise stripping of different cable types.
- Fixed Dovetail Clip Port: For secure handling during crimping.
- Wire Cutter: High carbon steel cutting head for clean cuts of wires up to 8mm diameter.
- Lock/Unlock Mechanism: Safety lock design to keep handles closed when not in use.
- Connector Crimp Terminal: For extending Ethernet cables.
- Cable Stripper: Precision stripping technology for Cat5e, Cat6, Cat7 network cables.




4. Operating Instructions: How to Make an RJ45 Cable
Follow these steps to properly terminate an RJ45 network cable:
- Trim Excess Cable: Use the integrated wire cutter on the crimping tool to trim the cable to the desired length.
- Strip the Jacket: Insert the cable into the stripping slot of the tool. Adjust the UTP/STP adjuster if necessary for your cable type (Cat5e, Cat6, Cat7). Squeeze the handles to strip off the outer jacket without damaging the inner wires.
- Separate and Arrange Wires: Untwist the individual wire pairs and straighten them. Arrange the wires according to either the T568A or T568B wiring standard. Ensure the wires are flat and in the correct sequence.
- Insert Wires into Connector: Carefully push the arranged wires into the pass-through RJ45 connector. Ensure each wire goes into its respective pin slot and extends slightly beyond the front of the connector.
- Crimp and Trim: Insert the connector with the wires into the RJ45 crimping die of the tool. Squeeze the handles firmly. The tool will crimp the pins onto the wires and simultaneously trim any excess wire extending from the front of the pass-through connector.
- Secure with Strain Relief Boot: Slide a strain relief boot over the crimped connector. This provides additional protection and prevents cable bending at the connection point.
- Verify Connection: Use an RJ45 cable tester (not included) to check for proper continuity and wiring sequence.

Wiring Standards (T568A and T568B)
The crimping tool includes a built-in diagram for T568A and T568B wiring standards to assist with correct wire arrangement.

T568A Standard:
- Pin 1: White/Green
- Pin 2: Green
- Pin 3: White/Orange
- Pin 4: Blue
- Pin 5: White/Blue
- Pin 6: Orange
- Pin 7: White/Brown
- Pin 8: Brown
T568B Standard:
- Pin 1: White/Orange
- Pin 2: Orange
- Pin 3: White/Green
- Pin 4: Blue
- Pin 5: White/Blue
- Pin 6: Green
- Pin 7: White/Brown
- Pin 8: Brown
Pass-Through Connectors and Strain Relief Boots
The included Cat7 pass-through connectors and strain relief boots are designed for 23-26AWG wires with an outer diameter of 1.3-1.45mm. The pass-through design simplifies wire arrangement and trimming, while the boots provide secure grip and tamper-proof protection.

5. Maintenance
- Cleaning: After use, wipe the tool with a clean, dry cloth to remove any debris or wire fragments.
- Lubrication: Periodically apply a light machine oil to the pivot points and moving parts to ensure smooth operation.
- Blade Replacement: The kit includes replacement blades. If the cutting or stripping performance degrades, replace the blades by carefully unscrewing the retaining screws.
- Storage: Store the crimper kit in its protective carrying case in a dry environment to prevent rust and damage. Ensure the safety lock is engaged when storing the tool.
6. Troubleshooting
- Poor Crimp/Loose Wires: Ensure wires are fully inserted into the connector and the tool is squeezed firmly until the handles meet. Verify the correct wire gauge for the connectors.
- Damaged Wires During Stripping: Adjust the UTP/STP setting on the tool to match your cable's outer jacket thickness. Ensure the cable is inserted straight into the stripper.
- Cable Tester Failure: Double-check the wiring sequence (T568A or T568B) against the diagram. Ensure all wires are fully crimped and making contact with the pins.
- Tool Sticking/Stiff Operation: Clean the tool and apply lubrication to moving parts as described in the Maintenance section.
7. Specifications
| Feature | Specification |
|---|---|
| Brand Name | ZoeRax |
| Model Number | WXQ-778N1-BL |
| Type | Cable Crimper |
| Certification | CE |
| Compatible Cable Types | CAT5e, CAT6, CAT6A, CAT7 (Stranded and Solid) |
| Compatible Wire Gauge | 23-26AWG |
| Cable Outer Diameter (Connectors) | 1.3-1.45mm OD |
| Max Wire Cutting Diameter | 8mm |
| Battery Included | No |
| Package | Yes (Kit with carrying case) |
8. User Tips
- Always double-check your wiring sequence against the T568A or T568B standard before crimping to avoid errors.
- For best results, ensure the cable jacket is stripped just enough to expose the twisted pairs, minimizing exposed wires outside the connector.
- Practice on a scrap piece of cable first if you are new to crimping to get a feel for the tool and process.
- Keep the tool clean and lubricated for consistent performance and longevity.
9. Warranty and Support
For warranty information or technical support, please refer to the manufacturer's official website or contact your point of purchase. Keep your purchase receipt as proof of purchase.