1. Introduction
The SWEVY Digital Alcohol Refractometer SW-82A is a portable and easy-to-use instrument designed for quick and reliable measurement of alcohol concentration. It is ideal for various applications including home brewing, baijiu production, and disinfection fields. Featuring a wide measurement range, high precision, automatic temperature compensation, and a one-click reset function, this device ensures accurate and consistent results.
Figure 1: SWEVY Digital Alcohol Refractometer SW-82A
2. Safety Information
- Read all instructions before operating the device.
- Keep the device away from direct sunlight, high temperatures, and corrosive environments.
- Do not immerse the device in water or other liquids.
- Handle the optical prism with care to avoid scratches or damage.
- Use only specified battery types (2*AAA).
- Keep out of reach of children.
3. Package Contents
Please check the package to ensure all items are present:
- SWEVY Digital Alcohol Refractometer SW-82A
- Dropper
- Instruction Sheet (brief guide)
Note: Due to air shipping restrictions, batteries (2*AAA) are NOT included in the package.
Figure 2: Standard Package Contents
4. Parts Identification
Figure 3: SW-82A Refractometer Parts Diagram
- Measuring Slot: Area where the sample is placed for measurement.
- Prism: Optical component for refractive index measurement.
- LCD: Liquid Crystal Display showing temperature, concentration, and other information.
- ZERO Button: Used for zero-setting the device with pure water.
- START Button (Power Button): Used to turn on/off the device and initiate measurements.
5. Specifications
| Parameter Name | Value |
|---|---|
| Product Model | SW-82A |
| Measurement Range | 0-80%Vol |
| Resolution | 1% |
| Measurement Accuracy | ±2% |
| Temperature Compensation | 10-40°C |
| Ambient Temperature | 10-40°C |
| Battery | 2*AAA (not included) |
| Size | 117*55*29mm |
| Weight | 113g |
| Use | Concentration |
Figure 4: Product Parameters
6. Setup
6.1. Battery Installation
The instrument is powered by two AAA batteries. To install or replace batteries:
- Locate the battery compartment cover on the back of the device.
- Rotate the cover to the 'OPEN' position and remove it.
- Insert two AAA batteries, ensuring correct polarity (+/-).
- Replace the cover and rotate it to the 'CLOSE' position to secure.
Figure 5: Battery Installation
6.2. Initial Zero-Setting
Before first use or if accuracy is in doubt, perform a zero-setting with clean water or pure water.
- Ensure the measuring slot is clean and dry.
- Using the dropper, place approximately 0.3 ml of clean water or pure water into the measuring slot. Ensure the water covers the prism completely.
- Press the 'START' button to turn on the device.
- Observe the displayed value. If it is not 0.0%, press and hold the 'ZERO' button for 2 seconds until the display shows 'Zero setting' and then '0.0%'. This calibrates the device.
- Carefully clean and dry the measuring slot after zero-setting.
Figure 6: One-Click Reset Function (Zero-Setting)
7. Operating Instructions
Follow these steps for accurate alcohol concentration measurement:
- Preparation: Ensure the measuring slot is clean and dry. Press the 'START' button to turn on the device.
- Sample Application: Using the dropper, place approximately 0.3 ml of the sample solution (e.g., alcohol, baijiu) into the measuring slot. Ensure the sample covers the prism completely.
- Temperature Compensation: Allow the instrument to sit for about 20 seconds after applying the sample. This allows the device to perform automatic temperature compensation for accurate readings, especially if the sample is too hot or too cold.
- Measurement: Press the 'START' button. The device will display the concentration, temperature, and refractive index.
- Cleaning: Thoroughly clean the sample slot immediately after each measurement to prevent residue buildup and ensure accuracy for subsequent tests.
Figure 7: Measurement Operation Steps
Video 1: Alcohol Concentration Meter Demonstration
8. Cleaning and Maintenance
Proper cleaning and maintenance are crucial for the longevity and accuracy of your refractometer.
8.1. Cleaning the Measuring Slot
- If there is dirt or residue in the measuring slot, or if the instrument has not been used for a long time, it should be cleaned thoroughly before use.
- If the measuring slot contains oiliness or is difficult to clean, use ethanol or soapy water.
- After cleaning with ethanol or soapy water, drip clean water into the slot and wash it with paper towels at least three times. Always discard the paper towels after each wipe.
- Avoid scratching the optical prism during cleaning.
8.2. General Maintenance
- Store the device in a cool, dry place when not in use.
- Remove batteries if the device will not be used for an extended period to prevent leakage.
- Avoid dropping or subjecting the device to strong impacts.
9. Troubleshooting
If you encounter any issues, refer to the table below for common problems and solutions:
| Error Message / Symptom | Reason | Solution |
|---|---|---|
| Excessive light | External light is too strong to measure. | Move to a less brightly lit area or shield the measuring slot from direct light. |
| High Temp / Low Temp | The temperature in the measuring slot is out of range (10-40°C). | Ensure ambient temperature and sample are within the operating range. Allow device/sample to acclimate. |
| Re zero | Zero-clearing step needs to be performed again. | Perform the zero-setting procedure with clean water (see Section 6.2). |
| Less solution / Less water | Too little solution or clean water in measuring slot. | Ensure at least 0.3 ml of sample/water is applied and covers the prism. |
| Out of range | Excessive concentration. | The sample's concentration exceeds the device's measurement range (0-80%Vol). |
| Low voltage | Low battery voltage. | Replace the AAA batteries. |
| Fault | Possible damage to components. | Contact customer support for assistance. |
10. User Tips
- For consistent and accurate results, always perform a zero-setting with pure water before taking measurements, especially if the device hasn't been used recently.
- Thoroughly clean the measuring slot immediately after each use to prevent residue buildup, which can affect subsequent readings.
- When measuring solutions with suspended substances, filter the sample using a filter spoon or gauze to remove solids before placing it on the prism.
- Allow sufficient time (approx. 20 seconds) for the sample to acclimate to the device's temperature for optimal automatic temperature compensation.
11. Warranty and Support
This SWEVY Digital Alcohol Refractometer SW-82A is designed for reliability and accuracy. For any manufacturing defects or operational issues not covered in this manual, please contact your retailer or the manufacturer's customer support for assistance. Keep your purchase receipt as proof of purchase for warranty claims.
12. Additional Resources
For a more detailed guide and further information, you can download the complete user manual in PDF format: