1. Introduction
Thank you for choosing the ZK-502M Mini Stereo Bluetooth Audio Amplifier Board. This module is designed for DIY audio enthusiasts, offering versatile audio input options including Bluetooth 5.0, AUX, USB flash disk, and computer USB. It provides a 2-channel stereo output suitable for both active and passive speakers. This manual will guide you through the installation, operation, and maintenance of your amplifier board.
2. Safety Information
Warning:
- Ensure the power supply is within the specified DC5-24V range. High voltage is recommended for high power output.
- The actual maximum voltage of a 24V battery is about 28V, which should be considered when connecting.
- This product includes overcurrent, overheating, and short circuit protection mechanisms. However, always handle with care to prevent damage.
- Do not connect the power supply to a 24V battery pack directly without verifying compatibility.
- Ensure sufficient audio input and power/current for optimal output power.
3. Package Contents
- Amplifier Board x 1
4. Specifications
| Parameter | Value |
|---|---|
| Product Name | Mini Stereo Bluetooth Audio Amplifier Module |
| Product Model | ZK-502M |
| Chip Solution | Domestic amplifier chip |
| Audio Input | Bluetooth+AUX+USB flash disk+Computer USB (plug and play) |
| Power Supply | DC5-24V (high voltage recommended for high power) |
| Compatible Speaker | 10-100W; 4-8Ω |
| Channels | Left and right stereo (stereo) |
| Bluetooth Version | 5.0 (>15 meters without occlusion) |
| Bluetooth Name | Wuzhi Audio |
| Protection Mechanism | Overheat, Overcurrent, Short circuit protection |
| Product Size | 60x60x29mm |
| Product Weight | About 66g (shell) |
Power Supply Voltage vs. Output Power (for ZK-502M):
- 12V: 8Ω/20W+20W, 4Ω/40W+40W
- 15V: 8Ω/35W+35W, 4Ω/60W+60W
- 19V: 8Ω/55W+55W, 4Ω/80W+80W
- 24V: 8Ω/70W+70W, 4Ω/100W+100W
Physical Dimensions:

Heat Sink:

Comparison with other models:

5. Installation and Setup
Follow these steps to install and set up your ZK-502M amplifier board:
5.1 Component Identification

The board consists of a PCB, upper and lower cover boards, a knob, key cap, heat sink, M2x7 screws, and M2x12 copper pillars for assembly.
5.2 Wiring Diagram

Connection Points:
- Power Input: Connect DC5-24V power supply to the 5.5x2.1 DC head.
- Audio Input:
- Bluetooth Input: Automatically detected when no other audio input is active.
- AUX Input: Connect external audio source via AUX IN port.
- USB Input: Connect a USB flash disk or computer USB to the USB IN port.
- Audio Output:
- Right Channel / Left Channel: Connect to passive speakers.
- Audio Output (Active Speaker): Connect to active speakers.
Note: Passive speakers and active speakers can only be chosen one at a time. The USB flash drive file system must be FAT32, with a maximum support of 32GB.
6. Operation
Once the amplifier board is correctly wired and powered on, you can operate it as follows:
- Power On/Off: Use the 'switch' button to turn the amplifier board on or off.
- Volume Control: Adjust the 'Volume' knob to increase or decrease the audio output level.
- Selecting Audio Input: The board supports multiple audio inputs. It will automatically prioritize inputs or allow selection based on connection:
- Bluetooth: Enable Bluetooth on your device and search for 'Wuzhi Audio' to pair.
- AUX: Connect an audio cable to the AUX IN port.
- USB: Insert a FAT32 formatted USB flash drive (max 32GB) into the USB IN port or connect to a computer via USB.
- Speaker Output: Ensure you have connected either passive speakers (to the Left/Right channel terminals) or active speakers (to the Audio Output port), but not both simultaneously.



7. Troubleshooting
If you encounter issues with your amplifier board, consider the following:
- No Sound Output:
- Check all wiring connections, especially power and speaker connections, as per the wiring diagram.
- Ensure the volume knob is turned up.
- Verify the audio input source is active and correctly selected (Bluetooth paired, AUX cable connected, USB drive properly inserted and formatted FAT32).
- Confirm that only one type of speaker (passive or active) is connected at a time.
- Distorted Sound:
- Check if the power supply voltage and current are sufficient for the connected speakers and desired output power. Refer to the 'Power Supply Voltage vs. Output Power' table in the Specifications section.
- Ensure the speaker impedance matches the recommended range (4-8Ω).
- Reduce the volume to see if distortion persists.
- Bluetooth Connection Issues:
- Ensure no obstructions are present between the amplifier board and your Bluetooth device (range >15 meters unobstructed).
- Try unpairing and re-pairing the device.
- Ensure no other Bluetooth devices are interfering.
- USB Playback Issues:
- Confirm the USB flash drive is formatted to FAT32 and its capacity does not exceed 32GB.
- Check if the audio files on the USB drive are in a supported format.
- Overheating:
- Ensure adequate ventilation around the amplifier board. The large heat sink is designed for cooling, but proper airflow is still important.
- Verify the power supply is within the recommended range to avoid excessive heat generation.
8. Maintenance
- Keep the amplifier board clean and free from dust. Use a soft, dry cloth for cleaning.
- Avoid exposing the board to moisture, extreme temperatures, or direct sunlight.
- Do not attempt to disassemble the board beyond what is necessary for installation, as this may void any potential warranty.
- Regularly check connections for any signs of wear or corrosion.
9. User Tips
- For optimal sound quality and power, always use a power supply that can deliver sufficient voltage and current for your chosen speakers.
- Experiment with different speaker impedances within the recommended range (4-8Ω) to find the best sound balance for your setup. Remember, a larger horn impedance with sufficient voltage/current may result in lower relative sound power.
- When using a USB flash drive, ensure it is formatted to FAT32 and does not exceed 32GB for reliable playback.
- Consider the placement of your amplifier board to minimize Bluetooth interference and maximize range.
10. Warranty and Support
For detailed information regarding warranty, returns, or further technical support, please refer to the official user manual PDF provided by the manufacturer. You can typically find this document on the product's support page or by contacting the seller directly.
A user manual in PDF format is available: View User Manual (PDF)