1. Introduction
Thank you for choosing the Hirisi B150 Carp Fishing Bite Alarm. This device is designed to enhance your fishing experience by providing clear audio and visual alerts when a fish bites. Featuring adjustable volume, tone, and sensitivity, it adapts to various fishing conditions. This manual provides essential information for safe and effective use of your bite alarm.
Figure 1: Hirisi B150 Carp Fishing Bite Alarm
2. Safety & Warnings
Important Safety Information
Read all instructions before use. Failure to follow these instructions may result in damage to the device, product, or personal injury.
- Warning: Keep the device and its cord out of reach of children under 3 years old.
- Keep away from children unless supervised by an adult.
- Do not use this product for purposes other than its intended use.
- Inspect the product before each use; do not use if damaged.
- Follow installation and operation guidelines to avoid injury.
- Do not expose to water or moisture.
- Handle with care to avoid cuts or injuries.
3. Package Contents
Please check the package for the following items:
- Hirisi B150 Carp Fishing Bite Alarm (main unit)
- Instruction Manual (this document, also available as a PDF: User Manual PDF)
Note: 1x 9V battery is required for operation and is NOT included.
4. Setup
4.1 Before First Use
Check the main unit and all accessories for damage. Remove all packaging and protective materials.
4.2 Battery Installation
The Hirisi B150 requires one 9V battery (not included). To install:
- Locate the battery compartment on the rear of the device.
- Open the battery compartment cover.
- Insert a 9V battery, ensuring correct polarity (+/-).
- Close the battery compartment cover securely.
4.3 Device Installation
The alarm features a universal mount thread for easy attachment.
- Fix the alarm onto your rod rest or bank stick using the universal mount thread at the base of the unit.
- Tighten the adjusting knob securely to prevent movement.
- Route your fishing line and place it against the sensing contact (roller wheel) to ensure sensitive detection.
Figure 2: Device Installation on a Rod Rest
5. Operating Instructions
The Hirisi B150 features intuitive controls for optimal performance. Refer to Figure 3 for control locations.
Figure 3: Hirisi B150 Control Layout
5.1 Power On/Off
Press and hold the central 'Long Press on/off' button for a few seconds to power the device on or off.
5.2 Volume Adjustment (V)
Rotate the 'V' knob (top right) clockwise to increase the volume and counter-clockwise to decrease it. Adjust to ensure clear alarm prompts.
5.3 Tone Adjustment (T)
Rotate the 'T' knob (middle right) to change the tone of the alarm. Select a tone that is easily distinguishable.
5.4 Sensitivity Adjustment (S)
Rotate the 'S' knob (bottom right) clockwise to increase sensitivity (detects even subtle line movements) and counter-clockwise to decrease it (reduces false alarms from wind or waves). Adjust according to fishing conditions and fish activity.
5.5 Fishing Operation
- After casting your line, tighten it and ensure it is properly in contact with the sensor (roller wheel) of the bite alarm.
- Wait for bites. The device will activate sound and light alarms (Run LED for line out, Drop LED for line in) once a fish pulls the line.
5.6 Fish Fighting
When the alarm goes off, lift the rod firmly to hook the fish. Control the reel drag properly to prevent line breakage and fish escape.
5.7 Video Demonstration
Video 1: Hirisi B150 Product Demonstration (Unboxing, Setup, Features, and In-Use)
6. Maintenance
6.1 After Use & Storage
- Turn off the power of the device.
- Wipe off any water, dirt, and debris from the device using a soft, dry cloth.
- Reset the sensitivity knob to a neutral position (e.g., mid-range).
- Store the product in a dry and cool place, away from direct sunlight and extreme temperatures.
- Remove the battery if storing for extended periods to prevent leakage.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Device does not power on | Low or dead battery; incorrect battery installation. | Replace with a fresh 9V battery; ensure correct polarity. |
| No alarm when line is pulled | Low sensitivity setting; line not in contact with sensor; device off. | Increase sensitivity; ensure line is on the roller; power on device. |
| False alarms | High sensitivity setting; strong wind/waves. | Decrease sensitivity; adjust line tension. |
| No sound from alarm | Volume set to minimum; speaker obstruction. | Increase volume; check for and clear any obstructions. |
8. Specifications
- Model: B150
- Type: Fish Bell/Alarm
- Material: ABS (Matte ABS Shell/Body)
- Power Source: 1x 9V Battery (not included)
- Features: High-sensitivity sensor, Adjustable Volume, Tone, Sensitivity, Bright LED Indicator, Dual Antenna, Weather Resistant (IPX6 Waterproof), Non-slip Buttons, Metal Adjustment Knobs, Universal Mount Thread, 2.5mm jack socket for swinger.
- Origin: Mainland China
9. User Tips
- Sensitivity Balance: Experiment with the sensitivity setting to find the perfect balance for your fishing spot. Too high might give false alarms, too low might miss subtle bites.
- Battery Life: Always carry a spare 9V battery, especially for longer fishing trips, to ensure continuous operation.
- Standalone Use: The Hirisi B150 is designed as a standalone bite alarm and does not pair with a central receiver unit.
10. Warranty & Support
For any questions, technical support, or warranty inquiries, please refer to your purchase documentation or contact the seller directly. Keep your proof of purchase for warranty claims.